Solenoid Testers
-
Product
Electrical Receptacle Testers
-
UEi Test & Measurement Instruments
Is a small device containing a power plug and three indicator lights, used for quickly detecting some types of incorrectly-wired electrical wall outlets.
-
Product
80-1000V AC Non-Contact Voltage Tester
5226
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 80V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
LINE-CORD AND MULTI-WIRE CABLE TESTERS
LCT-3
-
Model LCT-3 Line-cord tester is an automatic test set to check continuity, polarity and dielectric breakdown on three-wire line cords.
-
Product
Instrument Transformers Tester
TE30
-
Calmet Smart Calibration Devices
Electricity meters tester class 0.05 and 0.1. Three phase tester of current transformers and analyser of power network quality. It makes possible electricity meters testing on the site or in the laboratory.
-
Product
Load Cell Tester
LCT-Ultimate
-
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
-
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
-
Product
Analog Hipot & Insulation Tester
KT-5000Pi
-
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
Product
Sliding Peel Strength Tester
OST3000
-
Compared to the scratch test, the friction and wear test is considered to be a durability evaluation method that is closer to the actual situation
-
Product
Micro-Ohmmeter and Loop Resistance Tester
LRT 6000
-
LRT 6000: The right solution for impedance resistance measurement in compliance with all aircraft specifications on plane, helicopter, rocket, army vehicles for both production andmaintenance. It is a very easy-to-use and versatile instrument. Its ergonomics allow the user to use it either placed on the ground or across one's shoulder or chest. Awide back-lit LCDdisplay combinedwith an intuitive keyboard ensures simple and easy operation.
-
Product
Hot Wire Ignition Tester
-
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Wrist Strap & Footwear Tester
STME-COMBI
-
Statclean Technology (S) Pte Ltd
The Wrist Strap and the Footwear Tester checks for the operating conditions with the strap on the wrist or foot wear on the foot. It clearly indicates whether or not the resistance of the wrist strap/ footwear system including the wearer is at least 0.75 Meg ohms and not more than 10/ 100 Meg ohms respectively.
-
Product
Analogue (1kV below) Insulation Tester
4132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
-
Product
DMX Tester
DXT1
-
The new DMX Tester from NuDelta Digital is a feature-packed test tool you won't want to leave home without. It can send any level to any DMX address with simple commands similar to those found on the world's most popular lighting consoles. It can test for valid DMX signal and show you the level at any address. It can test continuity on all five pins of a standard DMX cable and indicate which pins are not connected or cross-wired. Runs for hours on a 9 volt battery (included).
-
Product
AMIDA 3001XP Tester
-
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
Product
Battery Tester
6470 BT
-
Standard Electric Works Co., Ltd
2000 counts. DC Voltage measurement. 4-wire resistance measurement. Data hold function. Low battery indication. 9V DC power supply. Measure battery types: Li-ion, Ni-Cd, Ni-MH. Simple operation. Lead resistance and contact resistance eliminated.
-
Product
Analogue ELCB Tester
810 EL
-
Standard Electric Works Co., Ltd
● Wiring check.● Can be used on 2 wires L-E (ELCB/RCCB/GFCI tester).● Can be used on 3 wires L-E-N (with wiring check).● Sense automatically 50 or 60 Hz.● No battery required.● Simple operation.● Current injected in phase with the voltage.● Fused.● Wide operating voltage (195Vac to 265Vac).● Other voltage optional (110V).● Robust.
-
Product
Coaxial Cable Tester
6106
-
Peaceful Thriving Enterprise Co Ltd
This device is designed to test the connection of F type coaxial cable. The testing includes continuity and cable mapping. The tester includes 4 mapping terminals with different color and a F type adapter, which are very helpful for cable identification.
-
Product
Insulation & Multifunction Tester (LCD Display)
4101 IN
-
Standard Electric Works Co., Ltd
● Measures Insulation Resistance, voltage (AC-DC) measurements.● Automatic hold facility.● Continuity test with a short circuit current of minimum 200mA.● Energy conservation is feature.● EnerSave™ limits the test duration to about 10 Seconds to save energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
Product
PAT Testers Kits
-
Our PAT testing kits are designed to increase efficiency when testing. We have an excellent selection of PAT testing kits available. They are designed to help the way you work by creating efficiencies and help you get more from your PAT tester in the field. Our PAT testing kits are available with and without software so you can streamline your reporting process and provide a full and complete service to your customers.
-
Product
Static Tester
-
Electrostate tester with LED indicator for the detection of static charge in the plus and minus range. An indispensable, inexpensive tool for the assessment and selection of materials in the living area, as well as the quality of the room climate.Buy Data Sheet
-
Product
De-Energized Tester
ALL-TEST PRO 7 PROFESSIONAL
-
The ALL-TEST PRO 7™ PROFESSIONAL uses our proven, patented technology to look beyond vibration, temperature, and ultrasound test methods – giving you instant answers on your motor’s health. It represents our 7th generation in product innovation that ensures the reliability of motors in the field and helps to maximize the productivity of maintenance teams everywhere.
-
Product
Scott Internal Bond Impact Tester
-
The Scott Internal Bond Impact Tester is used to determine tear resistance (Elmendorf). A sample is torn with the help of the pendulum device starting from a predetermined cut. The work required for a tear of a given length is measured.
-
Product
Vibration Testers
-
Application for vibration tester: used for measuring periodic motion, to check the imbalance and deflecting of moving machinery.Is pecifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.use the high-performance acceleration meter, realize the repetitiveness and accurate measurement. it has the function of testing axle bearing situation
-
Product
Industrial Battery Tester
-
The Industrial Battery Tester (IBT) has been designed for testing traction batteries or batteries for stationary applications. It can also be used for testing other types of batteries. The IBT performs charging and discharging in accordance with the programmed test schedule. Parameters are constant current, constant voltage, constant resistance and constant power.
-
Product
Anaerobic Jar Tester
LD-LAJ-A10
-
Anaerobic JarLD-LAJ-A10with 1.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
