Signal Conditioners
Circuitry that offsets, attenuates, amplifies, linearizes, and/or filters the signal to a A/D converter.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
ITA Module
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
VME 16-channel Differential to Single-Ended Signal Converter
V1250
-
The V1250 is a 16 channel differential to single ended signal converter in a 1-unit wide VME 6U form factor. It provides differential inputs (34-pin 2.54 mm header, Zdiff = 100 Ω) and single ended outputs (coaxial LEMO, Rout = 50 Ω).
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp
510143002
Receiver Module Insert
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp.
-
Product
64 Channel Dual IF Signal Processor
DP-VME-5247
-
DP-VME-5247 is a VME64x Dual IF Signal Processor . This dual channel up converter and down converter on-board real time data processing and analog output. This board is particularly suited for radar systems where the signals must be sampled at high rates and very high purity programmable signal generation. Application range encompasses IF signal processing, radar systems, communication systems, and IF data logging systems.
-
Product
Signalling
-
- Quick and easy mounting- Modern LED RGB technology, long life, reduced stock-keeping- Different modes configurable via IO-Link or setting menu- Also as standard version with digital inputs
-
Product
Signal / Micro Power/ Micro Coax, Module, ITA, QuadraPaddle, iCon Series, 100/15 Position
510161107
ITA Module
Primary mating module 510160107. (May mate with other Receiver modules, as well.)
-
Product
Signal Level Meter
HT828B
-
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
Product
I/Q Signal Generation for Digital Radio Standards
WinIQSIM2
-
R&S®WinIQSIM2™ was especially developed to easily generate digitally modulated signals on a PC. The graphical user interface allows intuitive operation by offering a convenient way to create standard-conforming waveforms for many configurable digital standards and to generate multicarrier signals and multisegment waveforms. With these capabilities, R&S®WinIQSIM2™ covers a wide range of applications.
-
Product
Signalling Testers
-
Anritsu's strong and flexible Signalling Testers are a key part of Anritsu's total wireless test and measurement solution, utilizing technology developed through our global leadership in this market.
-
Product
Portable Fluid Conditioners
PCL-III
-
Bemco PCL-III portable fluid conditioners are furnished as free standing caster mounted systems, ready to provide a reliable and precisely controlled flow of temperature conditioned fluid. To save floor space, these systems are also packaged with larger space simulators and thermal vacuum systems.
-
Product
Signal Analysis Software
-
Signal analysis software solutions support a wide spectrum of applications ranging from manual signal processing and individual signal analysis to fully automated signal recognition and processing in wideband scenarios. The products are available as standalone units or as integrable subsystem solutions for R&S COMINT system software or third-party system software.
-
Product
RTM Sensor Signal Conditioning Board
MS 3631I
-
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
Signal Generators
-
Whether the BPSG generators with their precisely generated RF signals for testing EMC shielding and EMI/RFI measurements, or the brand new SPECTRAN V6 VSG vector signal generators with a frequency range of 10 MHz - 6 GHz and a large number of modulation types, the Aaronia signal generators impress with their quality and price.
-
Product
GPS/GNSS Antenna Signal Splitter 2-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS221
-
INSTOCK Wireless Components, Inc
GPS221 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked port is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
Product
Linear Signal Splitters
-
Advanced Science and Novel Technology, Co., Inc.
DC to 25GHz broadband linear signal splitterOne differential CML-type input port and four phase-matched differential CML-type output portsDifferential input linearity range up to 1000mV p-pDifferential gain of approximately -1.5dBLow jitter and limited temperature variation over industrial temperature rangeSingle +3.3V or -3.3V power supplyPower consumption: 1.35WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 44-pin package
-
Product
Signal Amplifier
A10160
Amplifier
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
Product
Mixed Signal Oscilloscope - 500 MHz, 2 Analog Plus 16 Digital Channels
MSOX3052T
Oscilloscope
500 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Test Setup For Air Conditioner
-
SCR ELEKTRONIKS have developed TESTING SET UP FOR SINGLE PHASE / THREE PHASE MOTOR for carrying out Performance Test, Earth Contact Resistance Test, High Voltage Test, Megger Test and Leakage Current Test. It consists of Voltmeters, Ammeters and Wattmeters for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of Earth Contact Resistance Test, HV test, Megger Test, Leakage Current Test. All tests are provided with tripping cut off concept.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
Fault Insertion Unit
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Process Signal Converter/Isolator
4380
-
The Iso Verter II Isolator/Converter protects electronic circuits by completely isolating the input and output signals from each other and from ground. Both input and output ranges are fully field selectable with easy to adjust switches
-
Product
Reporting Tool for Dynamic Signal Analyzer
m+p eReporter
-
m+p eReporter is the powerful reporting tool of the m+p Analyzer dynamic signal analyzer. It provides test engineers with comprehensive capabilities for browsing and viewing data, copying & pasting data to ActiveX applications, importing test data from many third-party noise & vibration systems and automating repetitive tasks. This full functionality is available without any measurement hardware connected.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Twin Female Contacts and Round Posts (610138200 and 610138117)
510150137
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
Mixed Signal Oscilloscope 1 GHz, 2 Analog Plus 16 Digital Channels
MSOX3102G
Oscilloscope
The MSOX3102G 1 GHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
-
Product
TAP Signal Isolation Module
JT 2139
-
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
Product
9kHz to 20/40GHz Signal Generator
CSG Series
-
Corech Microwave’s CSG series of Compact Microwave Signal Generators（Signal Source）operate from 9kHz to 20GHz / 40GHz. It offers high dynamic output power -120 to +17dBm, ultra low phase noise: -105dBc/Hz@10KHz, low harmonics and spurious. These exceptional performances make CSG9K20GA / CSG9K40GA an ideal choice for many test and measurement applications, including Semiconductor, Quantum Technology, Radar and Communication etc.
-
Product
GPS Antenna Signal Splitter 4 Way, SMA Jack, 1000 - 2000 MHz, 50 Ohm
GPS410
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
