-
Product
Modbus Gateway With Ethernet for Woodward GCP-30 Genset Controls and LS 4 Controls
GCP-MG
-
GCP-MG is a next-generation Modbus/CAN gateway specifically designed to interface Woodward's GCP-30 series genset controls (GCP-31, GCP-32), and LS 4 circuit breaker controls with Modbus networks. The GCP-MG gateway has been developed in cooperation with Woodward to ensure the highest possible degree of interoperability with Woodward equipment.
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
-
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
7RTD IoT Modbus Ethernet Remote I/O
ADAM-6015
-
8ch RTDProtocols: Modbus TCP, RESTful API, ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusWiring burn-out detect functionIsolation protection: 2000VDCBuilt-in web server
-
Product
Industrial 2-Port Modbus Gateway
EKI-1222
-
Supports surge protection for D.C. power ports with line to line 2 KV, and line to earth 4 KV; for signal ports with 4 KV. Provides 2 x 10/100 Mbps Ethernet ports for LAN redundancy. Integration of Modbus TCP and Modbus RTU/ASCII networks.
-
Product
8Thermocouple Robust Modbus RS-485 Remote I/O
ADAM-4118
-
8ch thermocouple(can be set to voltage or current)Operation temperature:-40~85°C,Power input:10VDC~48VDCNoise protection: 4kV surge(power),4kV EFT,8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
RTU (Remote Terminal Unit)
R2+ RTU
-
*The R2+ Remote Terminal Unit (RTU) is a distributed architecture and large I / O capacity designed to meet the various demands of current Power SCADA / EMS applications.
-
Product
Modbus TCP Based Dual Ethernet Port I/O Modules
-
ET-7200 Modbus TCP Based Dual Ethernet Port I/O have 2 Ethernet ports for daisy-chain networking. They are configurable over a standard web browser. Support for Modbus TCP protocol allows easy integration with SCADA software.
-
Product
Web Based Ethernet Modbus TCP Modules
-
The ET-6000 series Modbus TCP based web-based Ethernet I/O modules have a built-in web server for configuration, I/O monitoring and control. You can configure them with a standard web browser. They can be used with our FREE EZ Data Logger Software.
-
Product
8AI/ 8DI/ 4DO/ 4-Slot IO Modbus /BACnet /101/104 /DNP3/PLC/Azure/AWS IoT RTU
ADAM-3600
-
Domain Focused Onboard IO -8AI / 8DI / 4DOHigh I/O Flexibility with 4-slot I/O ExpansionModbus & DNP3 ProtocolIEC 61131-3&C Programming LanguageOperation Temperature -40~70°CMultiple wireless options for Zigbee/ Wi-Fi/ 3G/ 4G/ GPRSHigh Performance CPU Cortex A8 600MHzLow Power DDR3L 256MB RAMEmbedded Real-time Linux Kernel
-
Product
Modbus Transmitter for LPPHOT01 Probe
LPPHOT01S
-
The transmitter LPPHOT01S converts the mV analog signal generated by the illumination probe LPPHOT01 into a digital signal suitable to be transmitted over a serial line RS485 with MODBUS-RTU protocol.
-
Product
WISE-71xx/WISE-72xx Modbus TCP Controllers
-
WISE (Web Inside, Smart Engine) are Modbus TCP based Data Acquisition Controllers that allow for remote monitoring and logic control through a web interface. They can trigger outputs based on inputs, send email alarms and can show the status through a web page. WISE Data Acquisition Modules can be configured through a web page to implement IF-THEN-ELSE control logic with just a few clicks; no programming is required.
-
Product
4DI/4DO Modbus Ethernet I/O
WISE-4050LAN
-
Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTP, MQTTSupports RESTful web API in JSON formatSupports local logging with RTC time stampSupports mobile device web configuration in HTML5Supports 10~30VDC power with reverse protection
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
