Fiber Fault Locators
-
Product
2.5mm Visual Fault Locator
3105
-
Anfkom International Co.,Limited
The 3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:Finding the breakpoint, poor connections, bending or cracking in fiber optic cables.Finding the faults of OTDR dead zoneEnd-to-end visual fiber identification
-
Product
High-efficiency Fiber Stretcher
PZ2
-
The PZ2 provides the most extensive stretch of our stretcher product family. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, white-light scanning interferometry and large angle modulation of interferometric phase. The PZ2 is ideal for use in OCT [Optical Coherence Tomography] and OCDR [Optical Coherence Domain Reflectometry] applications requiring scattering or boundary definition measurements.
-
Product
Cable Fault Location System
Syscompact 2000 M Pro
-
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
Product
Power Quality Measurement & Digital Fault Recording
-
In view of the growing number of factors with a disturbing influence on power systems and the ever increasing sensitivity of devices and installations on the consumer side, simple monitoring criteria such as undervoltage or overcurrent are no longer adequate. Reliable registration of all the relevant processes within the electrical power system calls for constant observation of a wide variety of derived parameters, such as individual harmonic content, system unbalance and interharmonics, and the swift identification of even slight deviations from the norm.
-
Product
RFoG Fiber Optic 1550nm Transmitter
T8500AC Series
-
The MX-T8500AC series externally modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital signals from 50-862 MHz for CATV applications.
-
Product
Fiber Assembly Eccentricity Measurement Instrument
KONCENTRIK V2
-
Multi-functional system for test and measurement of fiber optic ferrules & cable assemblies. Fast and automated measurements of eccentricity.
-
-
Product
Cable Locating Device
TM520
-
Coordinating with high-voltage signal generator, test sound and magnet simultaneously, locate high-resistance and arc-over fault of the power cable. While fixing the fault point, the instrument can test the cable path as well.Coordinating with audio-frequency signal generator, test audio frequency induction, locate low-resistance fault, and identify the cable and test the depth of it.
-
Product
Fault Recording Monitors
-
Comprehensive, flexible, scalable and compatible – full multi-function devices.
-
Product
Fiber Optic Modem
VCH-608
-
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
Product
Fiber Cleaver
CARY-C500
-
The CARY-F600H optical fiber cleaver easy to use, convenient, rotating blade, no positionlimited, high-precision cutting. Optical fiber cleaver light weight. Cleave angle: < 1 degree .Replaceable blade cleave blade with 16 cleave spots.
-
Product
Live Fiber Identifiers
-
Wuhan Sunma Technology Co., Ltd.
Live Fiber Identifier are essential installation and maintenance instrument in data networks, CATV and telecommunication networks. Fiber identifier can identify the optical fiber by detecting the optical signals transmitted through the cables. SunmaFiber supply different types of Fiber Identifiers and Talk Set to meet you requirement, and they are with rechargeable battery and power supply adapter, so you can use them easily.
-
Product
Fiber Cleaning Kit
TK1013
-
This is a general purpose fiber cleaning kit for most popular fiber optic connector styles with 2.5mm and 1.25mm ferrules. Replacement consumables are also available. The combination of wet and dry-cleaning items here are proven and well-accepted by most organizations.
-
Product
Locate and Map Underground Utilities
UtilityScan DF
-
Geophysical Survey Systems, Inc.
UtilityScan DF incorporates our innovative dual-frequency digital antenna (300 and 800 MHz) and an easy-to-use touchscreen interface to view shallow and deep targets simultaneously in a single scan.
-
Product
Location & Business Datasets
-
Transform any analysis with Alteryx Location + Business Insights datasets. Build transformational outcomes with ready-to-use data from trusted market-leading providers directly within Alteryx Designer.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
Fiber Optic Sensors And Fiber Optics
-
Over 350 customized fiber optic solutions. Smaller, more precise, faster. Robust - High-temperature, chemically resistant, mechanically robust glass or plastic fibers. Better performance - Position-independent detection of irregular objects or liquids. Plug & Play - Intuitive parametrization with the Baumer Sensor Suite via IO-Link.
-
Product
Cable Fault Meter
-
A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
Product
Fiber Optic Transmitter/Receiver & Repeater Board
-
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A
40-191B-012
Fault Insertion Unit
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
VALVE & BOX LOCATOR
7-T
-
Rugged "Cycolac" instrument housing and detection headTelescoping HandleVisual Meter & Battery TesterBuilt-in speaker, signal and battery test meterOne sensitivity control knobBalanced and lightweight Adjustable extensionSet of stereo headphones3 Replaceable "AA" Alkaline batteriesDependable
-
Product
Fiber Optic Strain Sensors
-
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
Rebar Locator
Profoscope +
-
The Profoscope+ is a fully integrated rebar locator with data storage. To increase the efficiency on the construction site this enhancement of the Profoscope not only offers real time visualization of rebars, but also automatic data collection. Writing down measuring results of testing series is a time consuming business that can be an unnecessary source of errors. The various data storage modes of the rebar locator Profoscope+ make note taking obsolete. This cordless rebar detector is ideally suited for one-handed operations, keeping the other hand free for marking rebars.
-
Product
Fiber Optic Pressure Sensors
-
Opsens Solutions optical pressure sensor delivers reliable results in harsh environment. Opsens Solutions OPP series fiber optic pressure transducers are designed to provide accurate pressure measurement in the most adverse conditions. Its small size and EMI/RFI/MRI immunity makes it the ideal sensor for industrial applications.
-
Product
Precision Locating System
Pathfinder PLS
-
The Pathfinder PLS is RYCOM's Precision Locating System for the damage prevention specialist...
-
Product
*Ultrafast Fiber Lasers
-
Fundamental building blocks of many photonic systems used in industrial and medical applications as well as for scientific research.
-
Product
AutoCheck Intelligent Fiber Endface Inspector
CA3007
-
CA3007 AutoCheck is a stand-alone intelligent fiber endface inspector with auto analysis function, it will help the customers to judge the endface performance automatically even you do not have any knowledge about the endfaces
-
Product
Pipe & Cable Locator
505
-
Split box locator, Inductive Operation, Conductive Operation, Locate Unknown Pipes, Peak Method, Null Method, Very Accurate Depth Location.
-
Product
Fiber End-Face Inspection Interferometer
CLEAVEMETER 3D
-
The CLEAVEMETER 3D™ is a non-contact interferometer designed for inspecting the end-faces of cleaved or polished optical fibers with cladding diameters of 125 µm to 1200 µm. It gives immediate and precise information on important end-face properties such as flatness, perpendicularity, hackles and dust. Based on the NYFORS CLEAVEMETER 3D™ design, in addition to producing sharp fringe patterns it also generates three-dimensional images of the cleaved fiber end.
