C Battery
See Also: Battery, Lead Acid Battery, AAA Battery, AA Battery, 1.5V Battery, 9V Battery, Button Battery, Coin Battery, D Battery, NIckel Cadmium Battery, Lithium ion Battery, SLA Battery, VRLA Battery, NICAD
-
Product
Battery Conductance Tester
FST-8000
-
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
32 Channel, 1 Form C 2A Relay Switch
DP-cPCI-4509
-
The DP-cPCI-4509 is a 32 channel relay switch module. This module is constructed using 2 Form ‘C’ (DPDT) relays. It provides for 250V DC isolation between channels. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose. The user can write the command for the selected channels on to the Primary latch of the FPGA section. Readback is available to confirm the selected commands.
-
Product
Battery Testers
-
designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more.
-
Product
Battery Analyzers
Beta D-50
-
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
Product
Scienlab Battery Test System - Cell Level
SL1007A
Test System
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
Product
Battery Powered Telemetry Systems
-
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Battery Pack PCM Test Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
This battery PCM/PCB test equipment is suitable for the basic parameter test and protection function test of lithium battery pack protection board of mobile phone & digital products; it is also used for downloading, comparing and PCB calibration of battery management.
-
Product
cRIO-9040, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
785624-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9040 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for … data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Battery Test Equipment
-
Battery test equipment refers to instruments and devices used to assess the performance, capacity, and condition of batteries.
-
Product
Battery Analysis Software
-
Battery characteristics vary over time and depend very much on maintenance and the environmental conditions of the specific application. Each installation tends to have its own 'fingerprint'. Capturing and managing this critical operational data has always presented a challenge to facilities managers. Recording and analysing data using traditional pencil and paper methods is both time consuming and prone to error.
-
Product
Battery Tester
BT-100A
-
Konstar Electric Industrial Co., Ltd
Battery tester can test the car battery whether is ok, if the battery is bad or need chanrge or bad, the tester will give you the right check reasult, then can do the right plan for the battery before work.
-
Product
Battery Analyzers
-
JUNXY battery internal resistance & conductance tester is a portable and hand-held battery test and measurement instrument for daily battery maintenance. It offers users a fast and reliable principle to on-line check groups of battery bank’s battery state of health (SOH), battery performance by quickly and precisely testing each cell voltage, internal resistance, conductance, connecting strip resistance and so on.
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
Battery Tester
BAT-250
-
The Amprobe BAT-250 Battery Tester is designed for one-handed, comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
Product
FieldFox C Handheld Microwave Analyzer, 6.5 GHz
N9914C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
Configure Battery Pack Simulator for Battery Management System (BMS) Hardware-in-the-Loop (HIL) Testing
Simulator
Customized configuration for battery pack simulator by Bloomy
-
Product
NI-9265, 4-Channel C Series Current Output Module
783733-01
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
Shore C Rubber Durometer
LX-C
-
Shenzhen Chuangxin Instruments Co., Ltd.
LX-C micropore durometer applys to low hardness materials like micropore material used in foam, sponge, shoes. This durometer refers to HG/T2498-93 and other relevant standards.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel
41-752A-002
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
Product
Lithium Battery Equalization Tester
LIFG-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
LIFG-CT series tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem of inconsistent voltage of lithium battery pack.
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
Standard 0.66 (18.70) - 4.50 (128.00) Battery Probe
CP-2LB-4
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 39Full Travel (mm): 1.00Recommended Travel (mil): 30Recommended Travel (mm): 0.75Overall Length (mil): 158Overall Length (mm): 4.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Laboratory Battery Tester With Integrated Chamber
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
CTEK MUS 4.3 TEST&CHARGE Battery Charger and Tester
56-959
-
The MUS 4.3 TEST&CHARGE combines an advanced micro-processor controlled battery charger with a battery and alternator test function to provide the ultimate in battery testing, charging and maintenance.
-
Product
cRIO-9045, 1.30 GHz Dual-Core CPU, 2 GB DRAM , 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
785623-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM , 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9045 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing.
-
Product
Thermocouple Contact, Receiver, Copper, Type T (°C)
610113168
Thermocouple Contact (Receiver)
Primary mating contact 610113169.
-
Product
Battery Powered, Stand Alone Water Level and Temperature Data Logger
Level1000
-
The Level1000 is a rugged, submersible, battery powered, stand alone, water level and temperature data logger. Its stainless steel enclosure makes it perfect for use in lakes and streams. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 16,383 measurements.
