Interrupters
-
Product
Voltage Testers
-
The non-contact voltage tester detects live conductors on cable connections, cable drums, sockets, switches, junction boxes etc. Due to capacitive measurement procedures, no current flow is required and interruptions can be indicated quickly and accurately.
-
Product
Dual Channel, Low-Noise DC Bias Card
PI-41701
-
The PI-41701 is a dual channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V and features programmable current limits with LED indicators and software interrupt to show/alert the user if the channel is in current limit. This card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output.
-
Product
Hot Swap & Hot Plug
-
Renesas offers several hot swap and hot plug controllers that enable inserting and/or removing components without interruption to a system.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
-
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
PCI Digital I/O
APC424
-
The 16 TTL input/output channels can be programmed as inputs or as outputs on an individual channel basis. The 24 differential input/output channels are programmed as inputs or outputs on an 4-channel port basis. All input channels can be enabled for change of state, low, or high level transition interrupts.
-
Product
Wire Sorter
-
Shanghai Beha Electronics Co., Ltd.
*Standard signal transmitter identifies up to 12 lines*Clear indication of short circuits, open circuits, or interruptions*Integrated continuity tester
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
-
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
-
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
-
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
Product
USB-8506 , LIN Interface Device
784664-01
-
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Acquisition Of 8 Displacement Transducers
APCI-3701-8
-
PCI interface to the 32-bit data bus Acquisition of 16 or 8 inductive displacement transducers (Half Bridge, LVDT) 8 or 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
Product
Real-Time Clock & Interrupt Module
RCIM IV
-
The Real-Time Clock & Interrupt Module (RCIM IV) is a multifunction card designed for time-critical applications on Concurrent Real-Time’s iHawk™ multiprocessing systems. The RCIM provides key functionality for single system as well as multiple system applications.
-
Product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
-
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
Circuit Breaker Finder
6504
-
Peaceful Thriving Enterprise Co Ltd
Circuit Breaker Finder is a multi-function circuit tracer/ identifier. Circuit Breaker Finder identifies circuit breakers without interrupting service.This device is formed by 1x Transmitter and 1x Receiver. There are 3 functions: (1) Socket Tester (Wire Mapping)(2) Circuit Tracing / Identifying(3) Non-Contact Voltage Detecting
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
-
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
-
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
8-Ch, 16-Bit Counter/Timer Universal PCI Card
PCI-1780U
-
8 independent 16-bit counters8 programmable clock source8 digital TTL outputs and 8 digital TTL inputsUp to 20 MHz input frequencyMultiple counter clock source selectableCounter output programmableCounter gate functionFlexible interrupt source selectBoardID™ switch
-
Product
Regenerative Grid Simulator
61800
-
Chroma Systems Solutions, Inc.
Power rating: Up to 300kVA, single or three phase outputOutput Voltage: 0~330V L-N / 0~570V L-L0~400V L-N / 0~692V L-L opt. without using a transformerOutput Frequency: DC, 30Hz~100HzMaximum power delivered down to 200VAC L-NFull 4 quadrant, fully regenerative up to 100% of output current ratingSpecifically designed for PV inverter, Smart Grid and EV related test applicationsProgrammable slew rate settings for voltage and frequencyProgrammable voltage and current limitsTurn on, turn off phase angle controlLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetParallel output for higher power applications (three phase only)
-
Product
SparkFun Qwiic Twist
RGB Rotary Encoder Breakout
-
The SparkFun Qwiic Twist is a digital RGB rotary encoder breakout that is also able to connect to our Qwiic Connect System. The Twist takes care of all the various interrupts, switches, PWM'ing of LEDs, and presents all those features over an easy-to-use I2C interface. The Qwiic Twist was designed to get rid of the large mass of wires that are needed to implement an RGB encoder in a breadboard enabling you to stop messing around with interrupt debugging and get back to your project! Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
On-Line Electric Motor Analyzer
EMAX
-
We understand that shutting down electric motors for testing can be time consuming and costly. With the EMAX technology you can now test a motor while it is operating with no interruption to production. Within seconds the EMAX will provide a comprehensive detailed look at the Power Circuit, Power Quality, Stator, Rotor, and Air Gap.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-T
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
-
96 Channel Isolated Digital Input / Interrupt Output Module
-
Product
Test Engines
-
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
Product
UHF Multi-Frequency Belt-Pack IFB Receiver
IFBR1B
-
Wireless IFB (interruptible fold back) systems are used for talent cueing and crew communications in broadcast and motion picture production. In other cases, the IFB system is used by directors and other management to monitor program audio during a production. The IFBR1B receiver provides simplicity and flexibility in a package that is intuitive for untrained users to operate. Despite its tiny size, the new IFBR1B receiver offers excellent performance on par with all of Lectrosonics’ IFB products.
-
Product
4-Axis Quadrature Encode/Counter Universal PCI Card With 8-Ch Isolated Digital I/O
PCI-1784U
-
Four 32-bit up/down countersSingle ended or differential inputsPulse/direction and up/down counterx1, x2, x4 counts for each encoder cycleMultiple interrupt sources for precision application4-stage digital filter with selectable sampling rateOn-board 8-bit timer with wide range time-base selectorOptically isolated up to 2,500 VDC4 isolated digital input4 isolated digital outputBoardID™ switch
-
Product
Intel x51 Based Boards
MS 1507
-
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
Product
Single-Phase Static Switches
ISSF COMPACT
-
ISSF 'COMPACT' series circuit breakers are electrical devices used to interrupt or connect the flow of current in an electrical circuit. They are designed to provide high reliability and protection in a compact size. They overcome the limitations of electromechanical switches in many difficult and demanding applications, such as the control of high-power motors, transformers, tungsten lamps, heating elements, and electric ovens.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
-
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
-
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
NI-9266, 8-Channel C Series Current Output Module
785047-02
-
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
