Interrupters
-
Product
128 Channel Isolated Digital Input / Interrupt Module
DP-VXI-3117
-
DP VXI 3117 provides 128 isolated channel digital inputs for sensing DC levels and edge transitions of upto 48VDC. The input level selection for 5 (TTL / CMOS compatible), 12, 24 or 48V is made through on-board jumper selection. The debounce feature is programmable for a period of 2msec to 2147 sec. in binary increments. Channel groups 1 to 32, 33 to 64, 65 to 96 and 97 to 128 can each have a unique programmed debounce period, provided the ratio of clock period between groups does not exceed 32,768.
-
Product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
LIN Interface
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
Power Line Conditioner
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Product
VXI IP Carrier Module
DP-VXI-5124
-
The Data Patterns DP-VXI-5124 is a VXI 'C' size Carrier Board, which occupies a single slot in the VXI system. The module is a register based device with A16/A24/A32 address space and has interrupter capability. The carrier board's VXI bus interface is used to program and monitor the carrier board registers for configuration and control of the board. The VXI bus interface is also used to communicate with and control the external devices that are connected to an IP modules field I/O signals.
-
Product
Clamp Meters
-
Kyoritsu Electrical Instruments Works, Ltd.
The clamp on the device is simply placed around a live wire. This allows one to measure the current on a wire without interrupting the operation of the electrical appliance. A clamp meter uses digital technology to bring instantaneous readings.
-
Product
Single Port RS-232 Interface
PCI-COM232
-
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
Product
Vacuum Interrupter Tester
VIT
-
Veer Electronics make Vacuum Interrupter Tester that tests the Vacuum Interrupter Integrity by applying a Pulse DC Voltage across the Interrupter under Test. When this Voltage is applied to the Vacuum Interrupter, if Interrupter is defective then an electronic Buzzer gives Audio indication as well as Red color LED will gives Fail Indication. If Interrupter is in Healthy Condition, then the Instrument will gives Pass Indication with Green LED light.
-
Product
Multifunction I/O
526
-
Four 24-bit quadrature encoder inputsFour 16-bit analog outputsEight 16-bit analog inputsEight digital I/OSingle supply (5 V) input powerProgrammable interrupt timerVersatile watchdog timerxPC Target Real-time rapid prototyping softwareavailable through MathWorks
-
Product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Low Profile, Onboard GBIP Analyzer
780936-01
Signal Analyzer
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
CAN Interface
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
IEC61000-4-11 Voltage Dips And Interruptions Simulator Generator
VDS-1120DX
-
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
Product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
CAN Interface
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Digital I/O Board
CPCI-1500
-
16 digital inputs, 24 V, including 14 interruptible inputs 16 digital outputs, 24 V, 500 mA/channel Optical isolation 1000 V Input and output filters Watchdog, timer After power-on the outputs are reset to ì0î
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
Fault Insertion Unit
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Synchronous GPS Based I/O Controller & Interrupter
interX
-
interX was originally developed as a measurement instrument for industrial and trunk pipeline anodic or cathodic protection systems. interX allows facilitate measurement of galvanic parameters (instant-off polarized potentials, pipe-to-soil potential) across a wide range of timing cycles. It is used to make synchronous disconnect and reconnect of protection electrodes (anode or cathode) or rectifier's from/to buried underground pipeline to perform measurements.
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Multifunction Power & Harmonics Analyzer
KM 2100 / KM 2200
-
Kusam Electrical Industries Limited
Volts / Amps. / Hertz, Dips & Swell, Power / Energy. Unbalance, Monitor, Scope, Harmonic, Logger &, Interruption functions. (KM 2200). Inter Harmonics, Transient Voltage, Inrush Current, Flicker function not available in KM 2200. Frequency upto 400Hz (KM 2100); 50 / 60Hz (KM 2200). Single-phase 2W / Single-phase 3W / 3-phase 3W / 3-phase 4W. Flash memory 128MB. TF Card 8G Memory Card for long-term measuring data storage. Support USB port to connect to PC and analyze the data / screen shots copied by U-disk. Support LAN port to make the remote control available, transfer the measuring data.
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
Isolated Digital I/O Card
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
Hydrogeology
HAPPIE
-
The H.A.P.P.I.E. program (Hazard of Aquifer Pollution Potential Impact Evaluation) provides a conservative answer to the problem of determining risk levels in emergency conditions, which means that areas where illegal waste disposal sites, overflows and ruptures of impermeable sheeting are present and where water withdrawal should be discontinued can be identified. H.A.P.P.I.E. in fact offers a conservative response to the problem of the determination of the environmental impact in critical conditions that can usually be correlated to the requirements of defining areas in which the supply operations should be interrupted in emergency conditions, therefore in very short times and without the possibility of obtaining an accurate collection of the hydrogeological data.
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
IP Parallel HV
-
High Voltage [up to 30V] IP Compatible card with 48 programmable IO. 40 mA sink. Open collector interface. Interrupt generator on each input channel. Filtered or direct input.
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
PCIe Digital I/O Board, 32 Optically Isolated I/O Channels, 24V
APCIE-1532
-
16 digital inputs, 24 V, isolated16 interruptible inputs16 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
M-Module Carrier for VMEbus (3U)
i4001
-
The i4001 is a 3U form factor M-module carrier for the VMEbus and forms the basics of a flexible I/O system. It offers the user a means of integrating M-modules in a VMEbus system. The i4001 has one M-module slot. M-module interrupts can be passed to the VMEbus. The i4001 supports vector-from-module and vector-from-baseboard, this means that interrupt vectors are provided by the the M-module or by the i4001.
-
Product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Test Engines
-
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
Product
Voltage Sag Generator
SKS-1120GTB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
Optical Fiber Identifier
-
Anfkom International Co.,Limited
It is an essential installation and maintenance instrument.By inserting the fiber into its adapter head,it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.The 3306A optical fiber identifier also allows relative core power display and identification of the 270Hz,1kHz and 2kHz frequencies. When they are used to detect the frequency, the continuously audible tone is activated.There are four types of adapter heads available: 0.25,0.9,3.0 and 2.0.The 3306A optical fiber identifier is powered by a 9V alkaline battery.
