Interrupters
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
NI-9266 , 8-Channel C Series Current Output Module
785046-01
Current Output Module
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
Product
ARINC 429 Test And Simulation PXI Module
PXI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Optical Fiber Identifier
BD-IF400D
-
Shanghai Baudcom Communication Device Co.,Ltd.
BD-IF400DOptical Fiber Identifier is an important tool for optical maintenance, which isused for nondestructive fiber identification project. Meanwhile it also hasVisual Fault Locator module with fault location function. Useingthe macro bending technology on line for nondestructive testing, BD-IF400DOptical Fiber Identifier can measure the signal direction and power and avoidmisoperation resulting in interrupted lines.
-
Product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
48-Ch Digital I/O And 3-Ch Counter PCI Card
PCI-1751
-
48 TTL digital I/O linesEmulates mode 0 of 8255 PPISupports both dry and wet contactInterrupt handling capabilityTimer/Counter interrupt capabilityBuffered circuits for higher driving capacity than the 8255Keeps the I/O port setting and DO state after system resetBoardID switch
-
Product
Current Transformer with Open Core
TCP
-
Lifasa - International Capacitors, SA
The TCP series is designed for installations in operation. It has a removable core that allows its connection without interrupting the power supply.
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-02
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
High Voltage Seasoning Equipment
-
This equipment is used to remove the bars that are in contact with the surface of vacuum interrupters.
-
Product
USB BUS Controller Board
MS 1711
-
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Load-to-Line Jumpers
200
-
TESCO’s Load-to-Line Jumpers (Catalog No. 200) allows the utility to perform meter maintenance without interruption of service to the downstream occupant. TESCO bypass jumpers are rated for 200 amps continuous duty and are made from a durable 1/8″ thick tin-plated copper with a durable insulating material covering everything except the blades.
-
Product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
Analog Input Module
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
Interface
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
Digital I/O Board, 64 Optically Isolated Digital I/O Channels, 3.3V
APCI-1564-3.3V
-
*For 3.3V PC systems*32 digital input channels, 3.3V, incl. 16 interruptible*32 digital output channels, 3.3V, 500 mA / channel*Optical isolation 1000V*Input and output filters*Watchdog, timer*After power/ON the outputs are reset to ì0î
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
-
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Visual Analysis of any Embedded System
SystemView
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER is announcing the release of SystemView, a free tool enabling the visual analysis of any embedded system. SystemView gives complete insight into the behavior of a program, with minimal side effects on the observed embedded system. SystemView offers cycle accurate tracing of interrupts and task start stop as well as task activation and API calls when an RTOS is used. It visualizes and analyzes CPU load by task and interrupts and scheduler. Test setups with LED and oscilloscope are a thing of the past.
-
Product
PMC-Parallel-IO
-
PMC-Parallel-IO provides 64 independent IO in one PMC slot. 64 mA open drain buffers on each IO. Two interrupt sources. External or internal clock reference. Custom state machine designs.
-
Product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
CAN Interface
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Transformer Winding Resistance Meters
RMO TW Series
-
The RMO-TW instrument can perform a simple, fast and reliable verification of a transformer on-load tap changer. This instrument allows measurements of a winding resistance at each tapping position of an on-load tap changer without discharging between tests. Problems with OLTC switching, such as interruption, can be detected with these measurements. The results are displayed on a backlit LCD screen.
-
Product
PC/104 Input/Output Module
PCM-UIO48C-16
Input/Output Module
The PCM-UIO48C-16 is a highly versatile PC/104 input/output module providing 48 lines of digital I/O. The major feature of this card is its ability to monitor 24 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O points.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
Digital I/O
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
Voltage Sag Generator
SKS-1132GTB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
Value DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285V
-
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsSupports linear and circular interpolationHardware emergency inputSupports E-GearSupports programmable acceleration/deceleration rateMemory buffer (10K points) for trajectory planning which is designed in DSP(Auto-blending is not supported)Position compares triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPPosition latchProgrammable interrupt and watchdog timerRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
Network Interface Controller
SPIDAR®
-
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
Signal Module
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
DDoS Detection and Mitigation
-
Increasingly, business is done online. This increases the risk of exposure to costly service interruptions caused by cyberattacks. Distributed Denial of Service (DDoS) attacks have emerged as one of the most common and impactful attack vectors aimed at business networks. Today, DDoS attacks account for 40% of all cybersecurity incidents, with some organisations facing multiple attacks per day. With the average throughput of volumetric attacks rising by over 3X in the last decade, DDoS prevention has become essential for any organisation that relies on its network infrastructure to do business.
-
Product
PCI-GPIB+, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows, Onboard GPIB Analyzer
778033-01
GPIB Controller
The PCI‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCI slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCI‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
