FMC
-
-
Product
DSP FMC Modules
-
Sundance Multiprocessor Technology Ltd.
FMC Modules with Digital Signal Processors
-
-
Product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
-
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
Product
DAQ FMC Modules
-
Sundance Multiprocessor Technology Ltd.
FMC Modules with both Analog to Digital and Digital to Analog sections.
-
Product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
-
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
Clock Distribution FMC Modules
-
Sundance Multiprocessor Technology Ltd.
Clock Distribution FMC Modules
-
Product
8 Channel DAC FMC Module
DACNF08 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF08 is a eight channel Digital to Analog converter FMC which complies with VITA 57.1-2010.It uses 4x AD9122 DAC chips, with a sampling speed of up to 1.2GHz
-
Product
Mezzanine FMC
FMC-516
-
Curtiss-Wright Defense Solutions
The FMC-516 provides the low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of data delivered to the FPGA host through the FMC-516.
-
Product
4-Channel ADC FMC Module
FMC103 – LPC
-
Sundance Multiprocessor Technology Ltd.
The FMC103 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC103 card provides four 12-bit 210 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC103 has the LPC (Low-Pin Count) 160-Pin connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
Product
3U OpenVPX FMC Carrier
VF361
-
Sundance Multiprocessor Technology Ltd.
The VF361 is a 3U OpenVPX module that leverages on the ALTERA Arria ® V SoC FPGA, ARM Cortex-A9, and Texas Instruments Keystone Multicore DSP technology to provide a high bandwidth processing platform, ideally suited for computation and bandwidth intensive applications such as RADAR, networking, SIGINT, EW, SDR and Video.
-
Product
5 Channel DAC FMC Module
DACNF05 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF05 is a five channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A. A single-ended external input or output clock is provided. The direction of the clock is programmable from the FPGA of the FMC carrier board.
-
Product
Octal 310 Msps, 16-bit ADC FMC Module
ADF-O310
-
The ADF-O310 ADC FMC module from DEG delivers eight channels, each with 16 bits of resolution at a sample rate of up to 310 Msps. Utilizing the Analog Devices AD9652, the ADF-O310 enables defense applications requiring higher dynamic range, greater ENOB and wideband sampling performance.
-
Product
Mezzanine FMC
FMC-520
-
Curtiss-Wright Defense Solutions
Through direct connection to a host FPGA, the FMC-520 provides a low cost, low latency path necessary for agile applications such as RADAR and EW. Conforming to the VITA 57 FMC standard, the FMC-520 simplifies developers’ integration of FPGAs and analog output into embedded system designs.
-
Product
PCIe FPGA Carrier For FMC, Virtex UltraScale™
PCI595
-
The PCI595 is based on the Xilinx XCVU440 Virtex UltraScale FPGA, which provides 2,880 DSP slices, 88.6 Mb RAM and 5,541,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to one DDR4, 64-bit wide, with 8 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
Product
Quad 12.0 Gsps 16-bit DAC FMC+ Module
DAC-Q30
-
The DAC-Q30 FMC+ module from DEG is a high sample rate, 16 bit quad channel DAC module. The Analog Devices AD9174 DAC device operates at 3.0 Gsps natively and up to 12.0 Gsps in interpolation mode. A VITA 57.4-compliant FPGA Mezzanine Card (FMC+) interface, the DAC-Q30 offers industry wide platform compatibility with the PCIe/VME/VXS/VPX carrier board of your choice. The DAC-Q30 and associated HDL firmware are compatible with AMD FPGAs.
-
Product
4-Channel DAC FMC Module
SMT-FMC211 – LPC
-
Sundance Multiprocessor Technology Ltd.
The main component of the SMT-FMC211 is the Texas Instruments 4 channel DAC – TI’s Quad 1.25GHz DAC3484. This device offers excellent SFDR performance better than 70dBc, with an output sample rate of over 312MSPS. It interfaces to an Artix-7 XC7A15T-2C FPGA using a 16 bit differential DDR bus.
-
Product
VITA 57.4 FMC+ HSPC Loopback Card
-
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
Product
10 Channel ADC FMC Module
ADCFN10-AC – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
Quad QSFP28/QSFP+ FMC+ Module
-
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
FMC Add-On Cards
-
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
Product
FPGA Mezzanine Card (FMC)
FMC DEL
-
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) created to produce pulses delayed by a user-programmed value with respect to the input trigger pulse. It has 4 output channels and one input trigger. The delay from the trigger input to each of the outputs can be set independently in a range from 600 ns to 120 seconds. It is implemented using a dedicated time-to-digital converter IC from the European company Acam.
-
Product
6U VPX UltraScale™ FPGA board with FMC+ sites
IC-FEP-VPX6e
-
Based on the latest Xilinx Kintex UltraScale™20nm FPGA, the IC-FEP-VPX6e is a 6U OpenVPX Front-End Processor (FEP) optimized for applications requiring DSP intensive processing in highly constrained environments.
-
Product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
-
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
Product
FMC Module
SMT-FMC510L
-
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
Product
Mezzanine FMC
FMC-518
-
Curtiss-Wright Defense Solutions
The FMC-518 provides high-speed, low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of the data delivered to the FPGA host through the FMC-518.
-
Product
PCIe Gen3 x8 FMC Module
-
VITA 57.1 FMC HPC ConnectorPCIe Gen3/Gen2/Gen1 x8 Slot (upto 64Gbps)Single module supports both PCIe Root Port & EndpointM.2 Key-M NVMe slot with PCIe Gen3 x2 interface & SATA3.0 interfaceMIPI DSI & CSI Connector through LVDS IOs32Kb-EEPROM
-
Product
2-Channel DAC FMC Module
FMC230 – HPC
-
Sundance Multiprocessor Technology Ltd.
The FMC230 is a dual channel DAC FMC with a very wide band. The two 14-bit D/A channels operate at 5.7Gsps (2.85Gsps direct RF synthesis) and are clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC230 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
-
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
