-
Product
Phoenix 3U cPCI Camera Link Frame Grabber
AS-PHX-D48CL-3CPCI32-B-CR
-
Phoenix-D48CL is a 3U CompactPCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
Product
PXI Frame Grabber Module
-
PXI Frame Grabber Modules work with any base-, medium, and full-configuration Camera Link cameras, and are ideal for many industrial, life science, and biomedical imaging applications. PXI Frame Grabber Modules support Power over Camera Link(PoCL) and can power cameras through PoCL-enabled cables. You can program the PXI Frame Grabber Module using the NIVision Development Module, or you can configure it using NIVision Builder for Automated Inspection(AI) software for faster development and simplified maintenance.
-
Product
Xcelera Frame Grabber Family
-
The Xcelera Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility. This unified and scalable platform currently supports high-performance Camera Link™ cameras.
-
Product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
-
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
Product
Framegrabber
FastX-APU
-
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
Product
PXIe-1435, Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module
781699-01
-
Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module—The PXIe‑1435 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PXIe‑1435 works with any base‑, medium‑, and full‑configuration Camera Link camera, and it is ideal for many industrial, life science, and biomedical imaging applications. The PXIe‑1435 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables. The onboard digital I/O includes four TTL, two optoisolated inputs, and one quadrature encoder.
-
Product
FireBird Camera Link 3U cPCI Serial Frame Grabber
AS-FBD-1XCLD-3CPCIS-2PE4
-
The FireBird Camera Link CompactPCI Serial card is a member of Active Silicon’s state-of-the-art FireBird frame grabber family. FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
CL MX4 Frame Grabber
Xtium-CL MX4
-
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CL MX4 is based on industry standard PCI Express™ Gen 2.0 expansion bus to deliver high speed access to host memory. The new Xtium series offers higher bandwidth to sustain Camera Link® 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color/monochrome cameras, all in a compact, half-length, single slot solution.
-
Product
1-Port PCI Express Camera Link Frame Grabber
PCIE-1121
-
Half-Size PCI Express Board Gen 2.0 x4Camera Link clock up to 85 MHzCamera Link Base/Medium/Full/80-BitSupports up to 4 independent camerasSupports PoCL and non-PoCL cameras with SafePowerImage sizes up to 268,435,456 x 16,777,216Independent I/O (trigger, encoder, strobe, etc) for each camera
-
Product
Electro-Optical Test Software
INFRATEST
-
INFRATEST is a powerful software for testing IR cameras, visible and NIR cameras, ICCDs, goggles and laser rangefi nders. Based on video acquisition modules compatible with a wide range of communication protocols, including LVDS, Camera Link, GigE Vision and all types of analog formats – CCIR, PAL, RS170, NTSC, INFRATEST acquires, displays and analyzes the video signal from all types of electro-optical devices.
-
Product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
-
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
Product
Xtium2 Frame Grabber Family
-
The Xtium2 series leverages the PCIe Gen3 x8 platform to deliver high- speed image transfers to host memory without CPU overhead. Featuring Camera Link HS® interface standards, supports Active Optic Cable and SFP+ modules, CoaXpress® 12, and Camera Link®.
-
Product
FireBird Camera Link Frame Grabber (2xCLD-2PE8)
AS-FBD-2XCLD-2PE8
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
Grablink DualBase
-
For two Camera Link Base or Lite configuration camerasDirectly compatible with hundreds of Camera Link cameras available on the marketSupports PoCL, Power over Camera LinkECCO: Extended Camera Link cable lengthPCIe x4 bus: 850 MB/s sustained delivery bandwidthFeature-rich set of 20 digital IO linesMemento Event Logging Tool
-
Product
Software
-
Active Silicon computer vision products are supported by a variety of software tools. We provide powerful user software and SDKs for CoaXPress and Camera Link frame grabbers with support across several operating systems. Additionally, a wide range of drivers for third-party machine vision and scientific imaging packages is available.
-
Product
Accessories & Cables
-
Active Silicon offer a range of accessories for our hardware products, including CoaXPress and Camera Link cables and FireBird IO adapters for use with our frame grabbers. The products listed on our website are in stock and readily available. Other cable lengths or adapter types, are available on request, especially for higher order volumes.
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
2-Port PCI Express Camera Link, Base Frame Grabber
PCIE-1122B-AE
-
Half-Size PCI Express Board Gen 2.0 x4Camera Link clock up to 85 MHzSupports 2 Base CL camerasSupports PoCL and non-PoCL cameras with SafePowerImage sizes up to 268,435,456 x 16,777,216Independent I/O (trigger, encoder, strobe, etc) for each camera
-
Product
Digital VIS-SWIR Camera
OWL 1280
-
Using a 1280 x 1024 InGaAs sensor from SCD, the OwL 1280 offers visible extension from 0.6µm to 1.7µm to enable high sensitivity imaging. The 10µm x 10µm pixel pitch enables the highest resolution imaging. It will offer less than 28 electrons readout noise (rms) and with a high intra-scene dynamic range of 51dB, this enables simultaneous capture of bright & dark portions of a scene. Available with a 12 bit medium Camera Link digital output, the Owl 1280 will run from 10 to 60Hz. The camera features an on-board Automated Gain Control (AGC) which enables the best contrast image from low to bright light. The camera also has an on-board intelligent 3 point Non Uniform Correction (NUC) providing the highest quality images. As with all Raptor cameras, the Owl 1280 is ultra compact and rugged. The camera sensor temperature is stabilised to 15°C and the camera does not have a fan.
-
Product
Framegrabber
FastX3
-
The FastX3 frame grabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX3, is a one half-length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. The front-end data is formatted and preprocessed by an Artix FPGA beforie being sent to the PCIe (X4) Gen 2 interface. It also is POCL and has isolated inputs including three LVDS I/Os.
-
Product
Phoenix PMC Camera Link Frame Grabber
AS-PHX-D24CL-PMC32-B
-
Phoenix-Dig24CL is a PCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
Product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
-
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
Product
Virtex-5 XMC/PMC
XMC-FPGA05D
-
Curtiss-Wright Defense Solutions
The XMC-FPGA05D high density I/O module controlled by a user programmable Xilinx Virtex-5 FPGA and supported by a range of front panel I/O modules including analog I/O, RS-485/422, LVDS and Camera Link.
-
Product
Frame Grabbers
-
* Supporting most performance-demanding Machine Vision protocols, such as CoaXPress, Camera Link HS, 10 GigE, Fiber etc.* Ideally suited for industrial, defense and aerospace Machine Vision Systems.* These products are complimented by sophisticated application software package and SDK, for Windows and Linux OS’s.
-
Product
Camera Link Breakout Box
CLB-501B
-
The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.
-
Product
CL PX4 Dual Frame Grabber
Xcelera-CL PX4 Dual
-
Building on the field proven technology and performance of Teledyne DALSA’s X64 frame grabbers the new Xcelera Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility. The PCIe host interface is a point to point host interface allowing simultaneous image acquisition and transfer without loading the system bus and involving little intervention from the host CPU. The X64 Xcelera-CL PX4 Dual is a highly versatile PCIe frame grabber capable of acquiring images from two independent Camera Link™ Base cameras and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 Dual an ideal solution to a wide variety cost-sensitive applications.
-
Product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
-
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
Product
IP Core and FPGA Products
-
Our FPGA offerings include development boards and IP cores for Altera FPGA devices. The IP cores include: I2C, PCIe, JPEG-LS, LVDS Camera Link and memory controllers.
-
Product
Grablink Full
-
For one Camera Link 80-bit, 72-bit, Full, Medium or Base configuration cameraDirectly compatible with hundreds of Camera Link cameras available on the marketECCO: Extended Camera Link cable lengthPCIe x4 bus: 850 MB/s sustained delivery bandwidthFeature-rich set of 10 digital IO linesMemento Event Logging Tool
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments.
