Gas Detectors
See Also: Gas Sensors
-
-
Product
Temperature Measurement IR Sensors & Detectors
M5
-
A thin film-based thermopile offering very low noise and a small 0.5mm diameter active area in a TO-5 package. This is one of the lowest noise thermopiles you can buy and provides a time constant 28ms time constant with Argon encapsulation gas.
-
Product
Dual Voltage Detector / Maintenance Tester
MicroPhase I
-
Hachmann Innovative Elektronik
MicroPhase I is an easily operated phase comparator, dual voltage detector and maintenance tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-testers warn against defect interfaces. The integrated "Universal Phase Comparator" compares two different interface signals, even if they are of different interface type or voltage. A unique error control avoids switching errors caused by erratic or unfeasible phase comparison.
-
Product
Multimeter With No Contact Voltage Detector V&A Multimeter
VA20/VA20B/VA20C/VA21
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
DIGITAL MULTIMETER : Misplug alarm Autorange multimeter with no contact voltage detector function.
-
Product
RMS Responding Power Detectors
-
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
Product
Extreme Low Power Detector Laser Power Meters
11XLP12
-
11XLP12 extreme low power detector is best suitable for low power im both the µW and mW regimes with very low thermal drift. Featuring broadband flat spectral response, minimal thermal drift and a noise equivalent power as low as 1 µW the 11XLP12 is ideally suited for measuring any pulsed or CW low power laser.
-
Product
IR Detectors
-
IR detectors have been a part of our standard product range at LASER COMPONENTS for almost three decades. A distinction is made between sensors for the near infrared range (NIR) from 1.0 µm to 2.5 µm and those for the mid-infrared range (MIR) above 2.5 µm. IR detectors of all modes of operation are a part of our product portfolio and leave nothing to be desired.
-
Product
Single Gas Sensor
Z-Gard® S MPO
-
The Z-Gard S MPO Gas Sensor connects directly to a building automation system for single gas monitoring solutions. It detects the presence of either carbon monoxide, nitrogen dioxide or combustible gases in air.
-
Product
Near Field Moving Detector Goniophotometer
LSG-1900B
-
LSG-1900B Goniophotometer is near field Type C automatic goniophotometric instrument for luminous intensity distribution measurement. The LSG-1900B uses a constant temperature detector. It is for industrial laboratory photometric data measurements of small luminaires, such as down light, bulb light, etc.
-
Product
Flaw Detector & Thickness Gauge
DFX-7+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Cellular Phone/RF Signal/ Wired Camera/Bug Detector
SH-055GRV / 01125
-
This Cellular Phone Detector / RF Signal Detector / Wireless Camera Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices
-
Product
Gas Gravimetric Sorption Analyzer
XEMIS Series
-
The XEMIS series offers reproducible, high resolution, high accuracy measurements even with small sample sizes or small uptakes, and performance unrivalled in a high pressure sorption analyzer.
-
Product
IR Detectors
-
Opto Diode manufactures high performance infrared detectors with a wide variety of active area sizes, cooling alternatives, packaging, windows, lenses, and filters options. These detectors are ideal for gas analysis, emissions monitoring, spectroscopy, process control, flame and fire monitoring. Our A Series lead sulfide (PbS) detectors provide the highest sensitivity in the 1µm to 3µm wavelength region. Our B Series lead selenide (PbSe) detectors deliver the best overall performance in a wider spectral range from 1µm to 5µm. Our multichannel (MCDs) devices are ideal for simultaneous detection of multiple gases including CO2, CO, and other hydrocarbons.
-
Product
Multi-Component Gas Analyzer
VA-5000 / VA-5000WM Series
-
The Multi-Component Gas Analyzer VA-5000 Series is an all-round analyzer that satisfies measurement needs as required for environmental monitoring, energy development support, quality controls, and continuous emission monitoring, etc. The VA-5000 Analyzer can be configured with up to 4 detector modules within a single case. Many combinations of detector modules with a wide selection of ranges allows this series of analyzers to be used for a variety of applications. The VS-5000 Sample Gas Conditioning Systems are designed to support the VA-5000 Analyzers by proving the optimal sample conditions for measurement. We also have wall mounted type analyzer (VA-5000WM) that enables to install in a limitted installation space.
-
Product
Handheld Online PD Detector
PD-SGS
-
Quick identification of PD activities in switchgear and cable accessories. The BAUR PD-SGS handheld online PD detector is used to conduct rapid initial tests for PD activities on live switchgear. Potential weak points are immediately signalled acoustically and numerically.* Initial rapid condition evaluation of switchgear and cable accessories during mains operation* Ideal for quick checks of MV and HV switchgear* Two integrated sensors:TEV sensor records PD on the surfaces of switchgearsAcoustic sensor records PD inside switchgears* Greater safety for test personnel switchgear tested for safety risks before starting work
-
Product
Mid-Range Gas Filter Correlation CO Analyzer
Model N300M
-
Teledyne Advanced Pollution Instrumentation
The Model N300M is a microprocessor-controlled analyzer used to determine the concentration of carbon monoxide (CO) in a sample gas. The analysis method is based on the Beer-Lambert law.The N300M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
Product
Detectors
-
Marktech offers the broadest line of both silicon and InGaAs detectors commercially available. Our main focus has always been in the area of application solutions to optimize your products performance. Our team of design engineers and R&D scientists are committed to providing you with unsurpassed technical support. Our detector series includes product ranging from UV through SWIR.
-
Product
Hydrogen Gas Analyzer
HyEVO
-
High-accuracy, high-resolution hydrogen gas analyzer designed to support the development of the hydrogen supply chain.Essential for the development of technologies necessary to produce, transport and use hydrogen and hydrogen related materials such as ammonia.HyEVO can be used for many applications in combination with other measurement devices.
-
Product
FTIR Exhaust Gas Analyzer Direct Measurement Type
FTX-ONE-CS/RS
-
The FTX-ONE offers a 5Hz sampling rate and simultaneously measure the concentrations of multiple components including NH3, CH4, and CO2, from (engine) direct exhaust gas using the Fourier Transform Infrared (FTIR) method in combination with multivariate analysis algorithm.
-
Product
Low-Barrier Schottky Diode Detector, 10 MHz to 18 GHz
8470B
-
The Keysight 8470B 18 GHz Low-Barrier Schottky Diode (LBSD) detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking. A video load (Option 002) extends the square-law region to at least 0.1 mW (-10 dBm).
-
Product
Nitrous Oxide Gas Sensors
-
The PST Dynament nitrous oxide (N2O) Platinum sensors are designed with patented non-dispersive infrared technology and contain all the necessary optics, electronics and firmware to provide a linearized, temperature-compensated output.
-
-
Product
Gas Chromatography
-
A gas chromatograph (GC) is an analytical instrument that measures the content of various components in a sample. The analysis performed by a gas chromatograph is called gas chromatography.Principle of gas chromatography: The sample solution injected into the instrument enters a gas stream which transports the sample into a separation tube known as the "column." (Helium or nitrogen is used as the so-called carrier gas.) The various components are separated inside the column. The detector measures the quantity of the components that exit the column. To measure a sample with an unknown concentration, a standard sample with known concentration is injected into the instrument. The standard sample peak retention time (appearance time) and area are compared to the test sample to calculate the concentration.
-
Product
H2 and Binary Gas Analyzers
-
PST offer a range of hydrogen (H2) and binary gas analyzers utilising the thermal conductivity property of gases to determine the concentration of a Target Gas (hydrogen for example) within a known Background Gas such as oxygen, nitrogen or argon.
-
Product
High Voltage Holiday Detector
AP-W
-
The Model AP/W can be customized for many applications, including In-Plant operations. Power from 115v or 230v AC Connection for external klaxon Custom cables for automated systems We can customize the AP/W to fit your needs. Contact us for details!
-
Product
Non - Contact Voltage Detector
Model 273 HP
-
Kusam Electrical Industries Limited
The 273 HP is a Non-contact voltage detector. It has two ranges for selection.The 273 HP consists of an internal pickup sensor, a function selection switch, a visual and a sound annunciator. With the 273 HP, physical contact with electrical conductors is not necessary when testing for live lines. Its sensor senses the radiated field which surrounds live conductors. Radiated field strength increases with voltage and decreases quickly with distance or earth shielding
-
Product
Industrial 4 Gas Combustion Analyzer
K905
-
UEi Test & Measurement Instruments
Hand-held indusrial Combustion analyzer with Wireles communication option
-
Product
Motor Exhaust Gas Analyzer
MEXA-ONE
-
MEXA-ONE offers an intuitive user interface with a highly efficient hardware and software design.This results in increased testing efficiency and economical facility operation, while enhancing reliability and accuracy. These advancements are possible because the MEXA-ONE software employs new "HORIBA ONE PLATFORM". This platform integrates the test devices in an emission cell into a single user interface, increasing efficiency and optimizing user control over the entire testing process.
-
Product
Voltage Detector
-
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
Product
Cable Integrated Detector
DTR-500
-
This machine is a multi-frequency with high-power transmitter, with constant power output and automatic matching of external load, which could ensure the machine to work in the best status. With ohmmeter, it could detect the external voltage and test the continuous circuit resistance to help judging the fault properties.
