Electrical Installation
-
Product
Photovoltaic and Electrical Installation Testers
-
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
-
Product
Photovoltaic and Electrical Installation Testers
3108
-
MI 3108 EurotestPV is a combined photovoltaic tester and electrical installations safety tester. It enables complete testing of electrical installations according to EN 61557 standards and in addition performs all necessary tests required on single-phase photovoltaic (PV) installations. This includes all of the tests as required by EN 62446, but also includes I - U characteristic, Calculation of STC values as required by EN 61829 and power measurements on Inverter’s DC and AC sides.
-
Product
Multifunction Electrical Installation Meter
AMPI-520
-
The AMPI-520 digital meter is designed to measure impedance in short-circuit loops without tripping the differential protection, it also measures the protection tare, earth resistance, continuity and phase sequence check.
-
Product
Single-functional testers
3110
-
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
Product
Multifunction Meter for Electrical Installations
AMPI-525
-
*Short circuit loop measurement:*Impedance measurement with 23 A (44 A phase-to-phase), short circuit resistance RZW =10Ω*Measuring range: 95...440V, frequency 45...65 Hz*Short circuit loop measurement with resolution 0,01 Ω , without tripping the differential protections (I∆n ≥30mA)*Automatic short-circuit calculation, phase-neutral and phase-phase voltage detection
-
Product
Multifunctional Electrical Installation Testers
Eurotest XA
-
The fifth generation of Metrel's multifunction electrical installation testers brought know-how in the testing procedures to reality. Because of the need to be efficient, faster and competitive but still responsible and concentrated on safety, all the technical content and innovations under AUTO SEQUENCE, rotate around taking care about testing procedures itself.
-
Product
Multifunction Electrical Installations Meter
MPI-520S
-
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
Product
Multifunction Electrical Installations Meter
MPI-525
-
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
Product
Multifunctional Electrical Installation Parameter Meter
AMPI-540
-
Much more than a multi-function meter*the largest 7" touch panel on the market - outstanding ergonomics and ease of use*removable microSD card - easy increase of memory capacity*lithium-ion battery - longer meter operation*possibility to add a voice memo or a photo to the measurement - multimedia description of the measurement site*
-
Product
Electrical Installation Testers
-
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
Product
Multifunction Electrical Installations Meter
MPI-520
-
The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.
-
Product
Multifunction Meter for Electrical Installations
AMPI-530
-
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
Product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
Optical / Electrical Converter
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
Optical to Electrical Converters
Optical / Electrical Converter
High bandwidth, broadband optical to electrical converters available in a range of configurations. Choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
Installation Tester
M72
-
Multifunction installation tester for insulation measurement up to 500V, continuity of protective conductors, phase sequence with TRMS multimeter functions.
-
Product
Installation Testers
-
Safety and performance are two of the most critical requirements for any electrical system. Good quality insulation, a properly working grounding system and active protection assure the safety of people, electrical systems and buildings, and protect them against electrocution, fire and other equipment damage.
-
Product
Multifunction Installation Testers
-
Megger multifunction installation testers are capable of performing various electrical tests.
-
Product
UltraCompact Installation Loudspeaker
UP-4slim
-
The UP-4slim delivers uncompromising fidelity in a slim, discreet design, so you can serve up a breathtaking sonic experience that never distracts from your star attractions.
-
Product
Multifunction Installation Testers
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
Product
Multifunction Installation Tester
COMBIG2
-
Multifunction installation tester with colour touchscreen display and WiFi compatible with HTANALYSIS™
-
Product
Electric Vehicle
-
Chroma Systems Solutions, Inc.
EV Automotive and Battery Test Advancements
-
Product
Rotating Electrical
-
Through its vast distribution network, WAI provides customers in the aftermarket with access to a wide range of product lines they need, when they need them. WAI’s production team is committed to consistently being the First-to-Market with the latest model products. This commitment, paired with the skill and expertise of the team, results in the introduction of more than 500 new products to the aftermarket each year. WAI offers 100 percent new alternators and starters as well as generators, motors, voltage regulators, rectifiers and other components for the Rotating Electrical market.
-
Product
Electric Testers
-
ATEQ offers a broad range of electric testers designed to meet the diverse needs of various industries. These testers, including advanced battery testers, are pivotal in ensuring the efficiency and safety of electrical systems. They are used in applications ranging from automotive and e-mobility to broader industrial purposes and EV battery testing. ATEQ’s electric testers are known for their precision, featuring integrated databases for battery types and parameters, secure systems with comprehensive battery protections, and user-friendly interfaces. This makes them essential tools in production lines, research and development laboratories, and for EV/HEV expertise
-
Product
Electrical Tomography
POLARES32
-
By exploiting an innovative technology based on the use of Alternating Current (AC), the POLARES32 Electrical Tomography can measure and display all the survey parameters at the same time: ground resistivity values, current, voltage, spontaneous potential, induced polarization and indication the quality of the measurement.
-
Product
PXI Rackmount Material for Installation
OTP2 module no.180
-
Materials required for flush mounting the PXI mainframe, also required for mounting the signal routing box
-
Product
Electrical Testers
-
CURT electrical testers are perfect for testing a new wiring harness on your vehicle or troubleshooting the existing wiring. Our trailer plug testers are built with LEDs and are available in 4-way, 5-way, 6-way and 7-way. We also offer brake control testers.
-
Product
PAT and Installation Verification Unit
PowerCheck 1557
-
The PowerCheck 1557 is a comprehensive PAT and installation verification checkbox. It carries out ongoing performance checks to ensure accurate measurement between calibration intervals. Fully tests Earth Continuity, Insulation Resistance, RCD Trip Time, RCD Trip Current, Loop, PE Conductor Current, Touch Current and Flash tests.
-
-
Product
Installation Tester
M74
-
M74 measures Overall earth resistance, tripping time of RCDs type AC, Insulation and Continuity of earth and equipotential conductors according to the laws in force in private electric installations.
-
Product
GPIB User Installable Interface Module
E363GPBU
Interface Module
Add a GPIB interface to your E36300 Series triple output or E36200 Series autoranging bench power supply.
