Serial Data
-
Product
Handheld Serial Data Analyser
SDA-02
-
Non-intrusively displays, captures and analyses electrical asynchronous data. Directly accepts RS232, RS485/422 and CMOS/TTL signal levels. Modbus over Serial Line protocol capability (RTU & ASCII), automatically checks & generates CRC/LRC, can act as master or slave.
-
Product
Interface Adapters and Serial Data Repeaters
-
Designed to provide a fan-out of up to ten RS-232 compliant outputs from a single input, the SSD120-100N-SDR is an all solid-state Serial Data Repeater. This device provides a simple and robust means of transmitting serial data to multiple aircraft systems in a small package.
-
Product
Digital Serial Data Audio Interface
PIO-9216
-
For accurate testing of devices that use the I2S, Left Justified, Right Justified and TDM audio data formats.
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
PC/104p Compatible Bi-Directional Serial Data Interface
PC/104p-BiSerial
-
The PC/104p BiSerial has been ported from the PMC BiSerial II. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PC/104p--BiSerial. The BiSerial features completely isolated FIFOs with 32 bit ports for increased adaptability and performance
-
Product
Serial Data Converters
CONV232/485 and CONV232/422
-
CONV232/485 and CONV232/422 convert between RS-232 communications (as used by the COM1 and COM2 ports standard on most motherboards) and balanced-mode, long distance RS-485 and RS-422 communications. CONV232/485 was designed for use with our REMOTE ACCES line when there is no RS-485 port on your PC, but may also be used in other, similar applications.
-
Product
PC based Serial Data Analyser
FSA32
-
This PC application is a tool to monitor and display asynchronous serial data. It can also transmit messages and monitor and set control lines. It has comprehensive triggering facilities, and runs on Windows 95 or later.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Jitter Noise Generator
J7000
-
The J7000A Series instruments high crest factor output is used as a random jitter source for serial data bus applications, including PCI Express Gen I & II, Serial ATA, and Fiber Channel. The noise source is designed for the PCI-SIG total jitter (Tj) model serial data application, but can be used for any random jitter noise application.
-
Product
MIL-STD-1553
-
CAES SµMMIT™ Interconnect Products provide an intelligent solution to address MIL-STD-1553 multiplexed serial data bus challenges in avionics and spacecraft onboard data handling subsystems for both military and civil applications.
-
Product
ULI-211CI -Triple Isolated RS-232/422/485 (Terminal Block) To Multi-Mode Fiber Converter (ST Connectors) DIN Rail Mounted
BB-FOSTCDRI
-
Converts serial data signals to multi-mode ST fiber optic2 KV 3-way optical isolation (input/output/power); EMI/RFI protectionData rate: up to 115.2 kbpsWide operating temperature: -40 to +80 °CDIN mount, IP20 plastic case10–48 VDC power source required (not included, sold separately)UL Class 1 / Division 2
-
Product
RS232 To RS485/422 Converter
-
This device transparently converts RS-232 serial data to RS-485 or RS-422. It allows the creation of reliable long distance data communication systems using standard computer hardware.
-
Product
Small Form Factor Recorder
Talon RTR 255x series
-
The Talon RTR 255x series implements Pentek's extensive line of digital serial modules including 40Gb Ethernet, serial Front Panel Data Port (sFPDP) and LVDS. All are capable of both receiving and transmitting data for recording and playback of data streams. The digital serial interfaces provide popular options for remote connection of the recorder to data sources. RTR 2555 - Ethernet: 1-, 10-, and 40-Gigabit Ethernet supporting both TCP and UDP protocols, with copper or optical interfaces.
-
Product
System for Analyzing Door Handles
-
In the production process of a vehicle door handle, the electrical functions of the component are to be tested. The mechanical testing of the operation of the door handle is performed by a PLC-controlled test system. In addition to the mechanical test, the electrical parameters: “serial data stream” and “impedance of the antenna” are to be analysed.
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
Ethernet
-
Ethernet, arguably the most common communication protocol on the planet, continues to spread into new markets and incorporates new protocols; it presents today’s Ethernet engineers with host of new test and validation challenges. Specifically, the increasing adoption of lossless Ethernet standards like FCoE, RoCE, and NVMf and increases in the line-rates of Ethernet from 10GbE and soon to 100Gb/s to name a few.These new physical and logical communications standards have exposed legacy test tools as outdated and incomplete for Ethernet product developers and the ecosystem. Teledyne LeCroy is addressing these needs by leveraging our extensive experience in high-speed serial data analysis tools currently used by many of the same companies developing products for NAS, SAN, LAN, and other high-speed protocol environments.The SierraNet Family of Ethernet test platforms provides best in class traffic capture, analysis, and manipulation for testing physical link characteristics and application operations. SierraNet is designed for addressing today’s high-speed storage and communications network problems and compliments other tools offering industry leading visibility and utility.
-
Product
PXI 36 Channel Data Comms MUX, 96-pin SCSI
40-735-912
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
VME Module
COM-1553B-3
-
The COM-1553B board gives the MIL-1553B designer an intelligent and versatile solution to multiplexed serial data bus design requirements. In applications that require the throughput and reliability of 1553B communications, the COM-1553B is a cost-effective system component with unsurpassed performance.
-
Product
ULI-344DC - USB To RS-232/422/485 (DB9 Male) Industrial Isolated Converter, 4 Port
BB-USR604
-
USB to RS-R32/422/485 ConverterUL Class 1/Division 22 kV IsolationLevel 4 ESD Protection (15 kV Air, 8 kV Contact)921.6 Kbps Serial Data Rate- 40 to + 80 °C Operating TemperatureDIN and Flat Panel Mounting OptionsTB and Power Jack 10-30 VDC Power InputsHigh Retention USB Connector, Plug in Serial Terminal Block
-
Product
1553Guard
-
MIL-STD-1553 bus architecture is a threat that adversaries can leverage to compromise your equipment and spread malicious software through your Serial Data Bus (SDB) system. You need a solution that can not only identify current and future cyberattacks in real-time but also instantly eliminate those threats before they wreak havoc and interrupt the mission.
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
Product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
13 GHz Differential Probe with ProLink Interface
DH13-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
DH Series PT Browser Tip, 16 GHz BW, 3.5 Vpp Range
DH-PT
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
