Pulse Current
-
Product
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse
T3CP50-50
-
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse.
-
Product
Ignition Pulse Detector
IP-3100
-
The IP-3100 enables ignition pulse detection of gasoline engines with high sensitivity. The rotation speed can be easily measured by clamping the primary side cord (low voltage), the secondary side cord (high voltage), and current cable of the electronic distributor. The IP-3100 is used with the tachometer made by Ono Sokki.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Pulse Signal Amplifier
VCH-606
-
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
Product
Pulse Tools
-
Faster than hand tools, more powerful than air screwdrivers, and safer than impact drivers, Mountz pneumatic pulse tools are a top solution for heavy fastening operations. Their pulse drive protects workers from injuries caused by high torque shut-off reactions. That means they can safely be used at higher torque settings than other power tools. High-speed rundowns decrease production cycle times, and the durable construction and simple maintenance needs ensure consistent tool uptime. Plus, a precise hydraulic shut-off keeps fastening work accurate for even the most heavy-duty applications.
-
Product
Current Probes
XQ13
-
Beijing GFUVE Electronics Co.,Ltd.
The model XQ13 ac micro amp clamp on current probe is suitable for 10A-100A cable online measurement, it belongs to high performance current sensor field.
-
Product
Current Loop Adapter
OP-1C
-
This adapter supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
Current Sense Resistors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Thick Film Current Sense Resistors (ERJ-B1, B2, xB, xBW, xCW) in a large range of case sizes and in wide terminal types for high solder joint reliability. The ERJ Series of Current Sense Resistors offers power ratings up to 2W with low ohmic ratings ranging from 5mΩ to 10Ω. Panasonic’s Thick Film Current Sense Resistor portfolio offers a more cost effective option with high reliability. Panasonic has a wide line of case size options ranging from 0402 to 2512 in conventional terminal and 0612 to 1020 for wide terminal.
-
Product
Single-point Current Meter
-
The SEAGUARD® is the core module used in small and medium sized underwater observatories. Whether used as a multipurpose instrument, or as a hub for strings in the water column, the SeaGuard manages connected sensors and the real-time communication of data and meta-data to shore. In autonomous configurations, long battery life is achieved with aggressive power routines keeping the full system at the lowest power levels possible.
-
Product
Current Calibrators
-
Used for basic measurements, tests and regulation techniques for setting and verifying test installations and instrumentation.
-
Product
Current Injection Sets
-
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
Product
OEM Digital Pulse Processor
DPP4553
-
The DPP-4553 is a high-performance and low power digital pulse processor board developed to be easily integrated in OEM systems. It integrates state-of-the-art performance in a very compact form factor, enabling high count rate application (up to OCR=1.8Mcsp @ICR=5Mcps) as well as low element detection down to Beryllium and Lithium.
-
Product
Pulse & Delay Generators
-
Berkeley Nucleonics Corporation
Provides high frequency pulses, delays and bursts. It is an ideal testing and timing control instrument for electronics, lasers or camera setup.
-
Product
Avionics Radio and Pulse Tester
T-RX
-
Streamline your avionics radio testing process with the CCX Technologies T-RX Avionics Radio and Pulse Tester. The T-RX is an all-in-one avionics tester that conducts 100+ tests on over 16 systems with only 1 device!
-
Product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-02
Current Input Module
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Precision Current Shunt
-
Has five precision selectable Ultra stable Current Shunts which ranges from 0.0001 to 1Ω. The Shunt T/C is less than 10ppm, and the internal current meter will measure from 1μA to 1000Amps.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Current Integrated Sources
CIS
-
The CIS current integrated source was designed to provide a stable alternating current source for the electricity meter test equipment, and in laboratories. The output current is isolated and independent from the mains voltage. Different CIS versions are available depending upon the values of output power and output current required.
-
Product
Precision Current Sources
-
DC Precision Current Sources provides precise and very stable output currents from 3 A to 10,000 A. The 6623A-PCS Series provides the best uncertainties of any DC high current sources (i.e. < 5 ppm of precision and stability at 1000A). In addition this Series is modular and initial output currents can be expanded at any time.
-
Product
Current Measurement Board
MS 1814
-
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
Product
Eddy Current Array
BRIO
-
BRIO is an advanced, ultra-portable Eddy Current Array (ECA) instrument designed for in-service inspections in aerospace, oil & gas, power generation, and manufacturing industries.
-
Product
DC-Coupled Pulse Amplifiers
-
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
Product
Group Pulse Generator
STT-EFT-5K series
-
Beijing KeHuan Century EMC Technology Co,.LTD
STT-EFT-5K series group pulse generator is designed to determine a common and reproducible basis for evaluating the performance of electrical and electronic product power lines, signal lines or control lines when subjected to electrical fast transient pulse group interference. The performance of the generator meets the requirements of IEC 61000-4-4 and GB/T 17626.4 standards. Application areas: industrial control, home appliances, medical electronics, communication electronics, components, automation control, etc...
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Current Converter AC
NMTI 2
-
A modern multipurpose quantity-to-current loop converter designed for installation in switchboards.
-
Product
Current Amplifier/Generator
ULCA-1
-
The Ultrastable Low-noise Current Amplifier ULCA-1 is designed to fulfill the needs of high-accuracy low-current generation and measurements in the range from 1 fA to 1 µA (licensed by PTB).
-
Product
Current Probe
PA-677
-
*Max. 70ADC/140Ap-p*Sensitivity: ≧2mA*Bandwidth: DC~1MHz*Rise Time: 0.35μS*Over Range Function*50mV/A, 500mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
Product
Current Differential Relay
SEL-587
-
Schweitzer Engineering Laboratories, Inc.
The SEL-587 Current Differential/Overcurrent Relay provides protection for any two-input apparatus, such as transformers, motors, generators, and reactors. Apply it for differential and overcurrent protection and use event reports for quick post-event analysis.
-
Product
Dual Channel 100 MHz Pulse Generator
PXIe-1209
Pulse Generator
The Astronics Test Systems PXIe-1209 PXI is a high-performance, 2-channel, 100 MHz Pulse Generator. Occupying a single PXI Express peripheral slot or hybrid slot, the PXIe-1209 provides dual independent pulse generation with fullcontrol of all timing parameters with extremely high resolution.
-
Product
Current Sources
-
Innovar Current Sources are the standard in the circuit breaker industry. Our Current Sources supply regulated current from 1 amp to 100,000 amps with incredible accuracy, along with providing a full set of features that is unmatched by any other Current Source in the market.
