Discrete I/O
-
product
PCI-6225, 80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779295-01
80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device - The PCI‑6225 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI-6517, 32-Channel, ±30 V, Sink Outputs, Bank-Isolated Digital I/O Device
779083-01
The PCI-6517 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6517 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6517 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-02
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
PCIe-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
786456-01
PCIe, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The PCIe-7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe-7846 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
Industry Pack Carriers and Digital I/O
CPCI-IPC
The CPCI-IPC module provides a 3U high performance flexible I/O scheme, that supports industry standard Industry Packs™. For application requiring low cost, high density I/O or unique combinations, the CPCI-IPC is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the CompactPCI bus. A very low cost, non-intelligent version is also available, CPCI-SIP.
-
product
PXIe-6363, 32 AI (16-Bit, 2 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
781056-01
The PXIe‑6363 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6363 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
6U cPCI Multi-function I/O Boards
78C2
NAI’s 78C2 is a 6U cPCI Multifunction I/O and Communication Board with six independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
FPGA PXI High-Performance Digital I/O Card
GX3700
The GX3700 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features 47,500 logic elements and 2.1 kb of memory. The GX3700 is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
product
PXI-6115, 4 AI (12-Bit, 10 MS/s/ch), Buffer Size 16MS, 2 AO, 8 DIO, PXI Multifunction I/O Module
778194-01
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PXI Multifunction I/O Module - The PXI‑6115 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications where synchronization among analog input, analog output, and digital I/O is required, 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
-
product
PXI-7953, Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780340-01
Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7852 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7852 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
PXI Semi-Dynamic Digital I/O Module, 16-Channel
40-419-004
The 40-419-004 is a 16-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
product
USB-7856, Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782916-01
Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7856 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7856 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
EMX-75XX
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
-
product
PXI Semi-Dynamic Digital I/O Module, 48-Channel
40-419-002
The 40-419-002 is a 48-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
PXI 32 Channel I/O, Low Side Driver
40-413-002
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
product
PCIe-6343, PCI Express, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device
781047-01
PCI Express, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device - The PCIe‑6343 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782262-01
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI-6230, 8 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Hybrid, Multifunction I/O
779616-01
8 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6230 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6230 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6230 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
6U CPCI D/S, S/D, I/O & Comm Board
78CS2
NAI’s 78CS2 is a 6U cPCI Multifunction I/O and Communication Board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five independent function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
PXI/PXIe Semi-Dynamic Digital I/O Module, 64-Channel
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
PXIe-6355, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783632-01
PXIe, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6355 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6355 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI-7854, Virtex-5 LX110 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780342-01
Virtex-5 LX110 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7854 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7854 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
