Insertion Loss & Return Loss
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Micro Power or Micro Coax, Insert, Receiver, SIM, 2 Pos, 2 Slot (not loaded)
510180104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
Signal, Module Insert, ITA, i2 MX, TriPaddle ,33 Position
510144006
ITA Module Insert
Signal, Module Insert, ITA, i2 MX, TriPaddle ,33 Position.
-
Product
VTAC Insert, Receiver/ITA, SIM (Only Available In Patchcords)
610151101
VTAC Insert
VTAC Insert, Receiver/ITA, SIM (Only Available in Patchcords)
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PIM & Return Loss Measurement
Range to Fault (RTF)
-
Range To Fault (RTF) is an exciting new technology from Kaelus that enables operators to accurately measure the location of PIM and Return Loss faults in their RF infrastructure. Reflection data together with PIM data provides an unmatched level of clarity for identifying the location of faults in the RF path.
-
Product
Core Loss Testers
S30 and S30S Series
-
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
Product
PXI 11-Channel 2A Fault Insert Switch
40-202-101
Fault Insertion Unit
This is the 11 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
Fault Insertion Unit
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI 30A Fault Insertion Switch 6-chan 2-bus
40-191-012
Fault Insertion Unit
The 40-191-012 is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
Tool, Insertion, Vertical VTAC, I2MX
910112134
Insert Tool
Tool, Insertion, Vertical VTAC, i2MX
-
Product
Blank Insert Kit, Receiver/ITA, SIM, VTAC, 10 Pieces
610151102
Insert Kit
Blank inserts are for unused VTAC module slots. One blank insert fills 1 slot in a VTAC insert-compatible module.
-
Product
PXI Dual Bus 64-Chan 2A Fault Insertion Switch
40-190B-102
Fault Insertion Unit
The Dual Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Optical Loss Test Set
KI23424OL-INGAAS-APC
-
A Quad Two-Way Optical Loss Test set / OLTS fiber tester that's perfect for medium to ultra high fiber count loss, length & optical return loss testing applications on both multimode and single mode fiber with APC connectors on both ports at 850 / 1330nm 1310/1550 nm. A pair of these compact SM & MM instruments set new standards of productivity, ultra-stable source accuracy and ease of use.
-
Product
Loss of Video Detectors
-
Program video and audio (balanced or unbalanced) is routed through the SG-8. With program video present at the input to the SG-8, the video and audio outputs of the SG-8 are the program signals. Upon loss of the video portion of the program input, the SG-8 defaults to internal SMPTE Color Bars and 1 kHz tone.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PXI 10A Fault Insertion Switch 10-Chan 2-Bus
40-199-002
Fault Insertion Unit
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
Product
Digital Iron Loss Tester
VDW 2065A
-
VEER make Digital Iron Loss Tester VDW-2065A is portable & easy to use Instrument which is very useful to find Watt loss of Electrical Steel immediately. Internationally accepted standard method of testing is Epstein Frame method which needs 30mm x 305mm size & min. 250g material for testing. Stamping And Laminations cannot be tested on Epstein Frame because of size. So, we have designed a direct reading type Single Sheet Tester Called Digital Iron Loss Tester VDW-2065A. It provides very fast testing of final products like Stamping, El & other laminations etc.
-
Product
Digital Iron Loss Tester
Model DW22
-
Digital Iron Loss Tester Dw22 is single sheet core loss tester which is useful to evaluate iron loss of electrical steel sheet CRGO, CRNO material and suitable for testing EI lamination, Motor Stamping, Fan motor stamping etc. Single sheet tester is suitable for quick & tentative idea of iron loss of sample. however for precision measurement user has to use Epstein Tester.
-
Product
Micro Coax/Micro Power, Module Insert, ITA, i2 MX, 15 Position
510144009
ITA Module Insert
Micro Coax/Micro Power, Module Insert, ITA, i2 MX, 15 Position.
-
Product
Optical Return Loss (ORL) Meter
OPTOWARE-S300 (FOTS-ORL Meter Systyem)
-
The Optical Return Loss(ORL) Meter is an efficient system for the characterization and test of optical components and systems to be performed in high quality.
-
Product
Micro Power or Micro Coax, Insert, ITA, SIM, 2 Pos, 2 Slot (not loaded)
510181104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Loss Test Set
-
Combines functionality in a compact test kit designed for performing length, loss (Tier 1) testing and inspection capability on both multimode and single-mode fibers.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
Fault Insertion Unit
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Return/Insertion Loss Meter
CA6034
-
The CA6034 optical return loss/insertions loss meter is an intergrated meter for optical fiber network, and cable manufacturere to verify the quality of finber leads, with the features of handhel, intelligent and multi-functional.
-
Product
Simple Loss Test Kit
KI-TK054
-
660/650 nm source & power meter. Interchangeable HFBR connectors
-
Product
Tool, Insertion, Vertical VTAC, VTAC SIM Modules
910112133
Insert Tool
Insertion tool for Vertical VTAC inserts. Tool layout is designed for use with 90 Series VTAC SIM Modules.
-
Product
Transformer Loss Measuring Bridge
MLS 7100
-
The MLS 7100 transformer loss measuring bridge was especially designed to greatly simplify the determination of transformer core and copper losses – an ideal choice when working on site. The measuring bridge features open circuit as well as short circuit measuring. Many transformers can be directly connected to the MLS 7100 without needing further transducers.
