Load Banks
Test a power source by providing controlled amounts of load to create conditions found in thier application.
See Also: AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks
-
product
DC Electronic Loads
Electronic Test & Power Systems
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.
-
product
Programmable DC Electronic Load
DL3000 Series
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics, aerospace and fuel cells.
-
product
Small Telemetry Compressive Load Cell
TC-3.0-SM
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.
-
product
Digital Control DC Electronic Load
IT8200 Series
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
-
product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
product
PXI 4 Banks of 20 Channel 2 Pole MUX
40-615-022-4/20/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
3U VPX RL Thermal Load Simulation Module
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
product
Electronical Load Board 3U CompactPCI (conduction cooled)
046-712
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Loading Rheostats (Resistive Load)
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
product
Dry Dielectric RF Coaxial Loads
4000 Series
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
product
Programmable DC Load Current Waveform Generator
9923
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
product
LED Load Simulator
63110A/ 63113A/63115A
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
product
High Power DC Electronic Load（1250V）
36300E Series（50KW/60KW）
36300E Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
product
Load Cells
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
product
PXI MUX 1 Bank of 128 Channel 1 Pole
40-610-022-1/128/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
Programmable 70W Electronic Load
MightyWatt R3
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
product
External Load Expansion Connector Accessory for USBHub3c
Used for connecting external electronic loads to the USBHub3c for VBUS load testing. It features separate screw terminals for VBUS passthrough from each USB Type-C port (0 through 5). While this board provides a physical wiring interface to access each VBUS channel, the USBHub3c External Load Feature is required to enable VBUS outputs on the USBHub3c.
-
product
Power Supplies And Loads
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
-
product
Electronic Loads
SLH AC/DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
Load Cell Indicator
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
Phantom Load Test Set
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
product
Single Point Aluminium Load Cell
EST-5
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
product
DC Electronic Load
EE30180A
The EE30180A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running.
-
product
PXI 20 Banks 0f 4 Channel 1 Pole MUX
40-615-021-20/4/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
