-
Product
Pressure Transmitter
PU/PD
-
- Measurement of gauge pressure with high accuracy 0.25%- Modularity of electrical and hydraulic connections with stainless sealed- Highly resistant to process conditions- Low cost & high stability
-
Product
Flaw Detector & Thickness Gauge
DFX-8+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Bonnet EFS for Horizontal Wellhead Completions
-
This Electrical Feedthrough System design provides a high-reliability circuit for transmitting electrical signals from downhole gauges through the wellhead and Subsea Tree to the Subsea Control Module (SCM) for topside monitoring. The system incorporates Teledyne DGO's high integrity glass-seal technology in three critical pressure barriers for maximum long-term reliability. The feedthrough system creates a permanent connection to the Subsea Control Module when the tree is installed onto the wellhead. In addition, a permanent rig-based DHG cable termination is completed to connect the control line to the feedthrough system. The DHG connector is available with a variety of sealing packages, including fully testable, dual metal-to-metal sealing of all downhole tubing hanger interfaces.
-
Product
Needle Microprobe
MT-29/1HT
-
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Material Testing & Physical Testing
-
Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Thickness Gauge
124
-
The Elcometer 124 Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex® Replica Tape.
-
Product
Vacuum Pressure Sensors
-
MKS, Granville-Phillips® Vacuum Gauges & Sensors cover a broad spectrum of vacuum measurement solutions.
-
Product
Vacuum Sensor, Thermocouple Vacuum Gauge for High Vacuum
DV-5 Series
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.
-
Product
4 Point Probe Sheet Resistance/Resistivity Measurement with Temperature Controled System
TCR-600
-
*Controlled Thermo-chuck (room temperature～600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy：±（0.5% + 1℃）
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 350 Ohm
40-265-012
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
ATEX Certified Ultrasonic Thickness Gauge
Cygnus 1 Ex
-
The Cygnus 1 Intrinsically Safe is a rugged, shock-proof multiple echo ultrasonic surface thickness gauge designed for safely measuring metal thickness to determine wastage or corrosion in potentially explosive environments. By using multiple echo technology the metal thickness gauge measurements are error checked using 3 return echoes to provide repeatable, reliable results.
-
Product
Multiplexed- Low-Level Function Card
-
Low-level multiplexed systems have a single programmable gain, wide-band amplifier following the input multiplexer. To accommodate low-level signal signals such as those from strain gauges or thermocouples and at the same time high level signals from other sources, the throughput rate must be limited to enable the high bandwidth amplifier to settle to the correct value after switching to a new channel. This results in a relatively low aggregate throughput rate when compared to an amplifier-per-channel system. A major benefit of a well designed low-level multiplexed system is the extremely high performance/cost relationship.
-
Product
Ultrasonic Thickness Gauge
UTG-2800
-
State of the art, digital ultrasonic thickness gauge is packed with features typically found on high end models only. This multi-functional ultrasonic thickness gauge offers everything from basic measurement, Scanning Capabilities, Adjustable Sound Velocity, extended memory and USB output capabilities.
-
Product
Coating Thickness Gauge
CM8855
-
It meets the standards of both ISO2178 and ISO 2361 as well as DIN, ASTMand BS. It can be used both in the laboratory and in harsh field conditions. The F probes measure the thickness of non-magnetic materials (e.g. paint,plastic, porcelain enamel, copper, zinc, aluminum , chrome etc.) on magneticmaterials (e.g. iron, nickel etc.) . often used to measure the thickness ofgalvanizing layer, lacquer layer,porcelain enamel layer, phosphidelayer, copper tile, aluminum tile, some alloy tile, paper etc. The N probes measure the thickness of non - magnetic coatings on non-magnetic metals .It is used on anodizing, varnish, paint, enamel,plastic coatings, powder, etc. appliedto aluminum, brass, non-magnetic stainless steel, etc. Automatic substrate recognition. Manual or automatic shut down. Two measurement mode: Single and Continuous Wide measuring range and high resolution. Metric/Imperial conversion. Digital backlit display gives exact reading with no guessing or errors. Can communicate with PC computer for statistics and printing by the optional cable. Can store 99 groups of measurements. Statistics is available.2.SPECIFICATIONSDisplay: 4 digits LCD, backlitRange: 0~1250 μm/0~50mil (other ranges can be specified )Min.radius workpiece: F: Convex 1.5mm/Concave 25mmN: Convex 3mm/ Concave 50mmMin. measuring area: 6mmMin.Sample thickness : 0.3mmResolution: 0.1 μm (0~99.9μm);1 μm (over 100μm)Accuracy: ±1~3%n or 2.5 μm or 0.1mil(Whichever is the greater)Bttery Indicator: Low batter indicator.PC interface: with RS-232C interfacePower supply: 2x1.5 AAA(UM-4) batteryOperating condition: Temp. 0~50℃ .Humidity <95% .Size: 126x65x35 mm; 5.0x2.6x1.6 inchWeight: about 81g(not including batteries)Standard accessories:Carrying case ...................1 pc.Operation manual ............ 1 pc.F probe in built .................1 pc.NF probe in built...............1 pc.Calibration foils ..............1set.Substrate (Iron) ................1 pc.Substrate (Aluminium)......1 pc.Optional accessories: RS-232C cable & software:1.USB adaptor for RS-232C2.Bluetooth interface
-
Product
Tool, Inspection Depth Gauge, Micro Coax, Receiver
910121179
Inspection Tool
Tool, Inspection Depth Gauge, Micro Coax, Receiver
-
Product
Wire Gauge Calculator
-
Calculate The Optimal Wire Gauge for Your DC Microgrid or Distributed Switch
-
Product
Variable Power Supply
VS-10a
-
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
Product
IEC60529 IPX5/X6 Water Jet Nozzle
CX-IPX56
-
Shenzhen Chuangxin Instruments Co., Ltd.
The IPX5-6 Jet Nozzle consists of a jet handle that is equipped with a pressure gauge and an easy-to-adjust flow valve. The interchangeable nozzles assemble easily to the jet handle. The nozzles are made from stainless steel.
-
Product
Surface Profile Gauge
SRT-6223
-
Specially used to take accurate measurement of the peak to valley height of the surface profile of the surface profile of blast cleaned surfaces.specifications:display: 4 digits. LCDRange: 0um to 800um (0mils to 30mils)Accuracy: +5% or +5( whichever is the greater)resolution: 1um (0.1mils)Metric and Imperial switchablePC interface: RS232CMeasurement speed: >30readings per minuteweight: 280gdimensions: 162x65x28mm(6.4x2.6x1.1 inch)operating temperature: 0-50℃ , 80% RHCase: high impact ABSBatteries: 4x1.5v (AAA) Batterystandard accessories included:carrying case: 1 pcoperation manual 1 pcoptional accessory:cable and software for RS232C
-
Product
Pressure Transmitter For Industrial Applications, Ratiometric Output
Series 21 C
-
KELLER AG für Druckmesstechnik
The C-series transmitters are noted for their ability to deliver high accuracy over a wide temperature range. This is achieved by means of mathematical modelling of the sensor characteristics and digital compensation. In order to do this, each transmitter is gauged over pressure and temperature, programmed and checked after calibration in the same test set-up.
-
Product
Data Logger with GSM/GPRS Module
HD33M-MB.2
-
GSM/GPRS data logger. RS485 MODBUS-RTU input, additional contact input for rain gauge. Great to combine with HD52.3D and HD51.3D series anemometers!
-
Product
Paint & Powder Coating Thickness Gauge
415
-
The new Elcometer 415 Industrial Paint & Powder Thickness Gauge provides simple, fast and accurate coating thickness measurements on smooth and thin industrial paint and powder coatings.
-
Product
Strain Gauge Weighing
-
In the demanding environment of the metals processing industry getting the right balance between accuracy, speed and reliability in your sensing systems can mean a great deal. ABB offers a wide range of dedicated products for weighing applications for crane, scrap, blast furnace and continuous casting.
-
Product
Digital Gauge Pressure
ZET 7012-I-VER.1
-
ZET 7012-I-VER 1 digital gauge pressure open membrane is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface.
-
Product
Dry Film Thickness
-
Dry film thickness, coating thickness or paint thickness as it is often known, is probably the most critical measurement in the coatings industry. It provides vital information as to the expected life of the substrate, the product’s fitness for purpose, its appearance and ensures compliance with a host of International Standards. In 1947, Elcometer launched one of the world’s first non-destructive coating thickness gauges, the Elcometer 101 Coating Thickness Gauge. For more than 6 decades, the design and production qualities of this rugged and reliable instrument have been the watchwords for all our products and these philosophies are still held today. Elcometer has a comprehensive range of Dry Film Thickness gauges to meet all of your coating inspection requirements.
-
Product
Automatic Transmission Oil Pressure Tester
ATG5AK
-
Checks oil pressure in automatic transmissions and gasoline engines on most domestic and import cars and light trucks. Includes 6' of oil proof nitrile hose to make testing easier as well as standard and metric fittings. 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar. 3-1/2" gauge has a dual scale dial with ranges from 0-400psi and 0-28 kg/cm2.
-
Product
Pressure Comparators
-
AMETEK Sensors, Test & Calibration
Our high-pressure, hydraulic pressure comparators are portable, self-contained, hydraulic pressure generators for calibrating pressure gauges, transmitters, sensors, and safety valves. They are much faster than deadweight testers and most automated pressure controllers; and it’s so quick and easy to use, it’s ideal for calibrating those low cost gauges that are often overlooked for ISO9000 compliance. Each pump is available on its own, or in one of our complete ready-to-use pump systems.
-
Product
Hardness-Rubber & Plastic (Dur
-
Durometers show the degree of hardness by value whether a non-rigid material like rubber is soft or hard (hardness gauge for rubber or plastic). Recently, JIS standard and ISO standard have been drastically revised and details of hardness tester of rubber and method of measuring hardness are changed.
-
Product
Vacuum Measurement
-
Agilent's full range of active and passive vacuum gauges and gauge controllers from atmosphere to UHV/XHV allow you to precisely and reliably control and measure vacuum. We offer Thermocouple (TC), Bayard Alpert (BA), Pirani, Inverted Magnetron (IMG), and Hot Filament (HFIG) gauges. Our gauge controllers are compatible with both Agilent and competitors' gauges and can handle up to 12 channels. Agilent controllers come with several communication interfaces including Profibus, ethernet, and RS-232/485 (other interfaces may be available upon request). There is also the option of a portable gauge controller (HGC-536).
