PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
Product
64-CH 16-Bit 250kS/s Multi-Function DAQ Card
cPCI-9116
-
- PICMG 2.0 Rev 2.1- 16-bit A/D and sampling rate up to 250kS/s- 64-CH single-ended or 32-CH differential input- On-board 1k-sample A/D FIFO
-
Product
RTD Measurement for PCI
PCI390
-
The PCI390 features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm-limit checking. Sensor-data is available in °C, °F, K and Ohms. All inputs are optically isolated from the system.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PC/104-Based Data Acquisition (DAQ) And Control Products
-
A small form factor embedded computer board, typically intended for use in small, space-constrained industrial control or vehicles systems. The standard size of these modules is just 3.550 × 3.775 inches (90 × 96 mm). The name PC/104 comes from the original IBM computer known as the "PC", and the number of pins used to connect the cards together (104). PC/104 boards are typically stacked on top of each other using stackable bus connectors and four mounting holes at the corner of each module. This provides a much more rugged, embedded computer that can be used in harsh environments such as those found in military or industrial applications.
-
Product
PCI-6123, 8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O DeviceMultifunction I/O Device
779409-01
-
8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device - The PCI‑6123 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6123 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6123 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
HPx-200 PCI Radar Input Card
-
The HPx-200 is a flexible, cost-effective PCI primary radar acquisition card that captures and processes one or two analogue or digital radar video signals from a single radar. The card is fully supported by SPx software, allowing modern radar processing to be added into legacy systems.
-
Product
6 Port PCI Express
PEX 8606
-
The ExpressLane™ PEX 8606 device offers 6 PCI Express Gen 2 (5.0 GT/s) lanes, which supports up to six ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX8606 is the industry's smallest 6-lane Gen 2 device and it enables users with the ability to connect multiple PCI Express endpoints which are used in a variety of consumer and embedded applications including ethernet routers, IO expansion modules, communication line cards as well as other low power applications.
-
Product
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ PCI Express Cards
DAQe-2213/2214
-
ADLINK DAQe-2213/2214 can sample up to 16 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 8 AI channels in order to achieve maximum noise elimination.
-
Product
MIL-STD-1553 One-Channel PCI Board
BRD1553PCI-1
-
The P-Orchestra™ is a one-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 16K word of internal RAM.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785959-01
-
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
88-lane, 44-port, PCI Express
PEX89088
-
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
-
Product
PCI Very High Density Multiplexer, 10-Channel, 16-Pole
50-670C-022-10/16
-
The 50-670C-022-10/16 is a 10-channel, 16-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Onboard GBIP Analyzer
780935-01
-
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
XMC Module Carrier PCI Express x 4
SK2-SESSION
-
SK2-SESSION is a bidirectional 4-lane PCI Express® Gen3 redriver, for optimum 8GT/s high speed signal integrity, and can be installed into any peripheral slot of a CompactPCI® Serial backplane.
-
Product
PCI 64xSPST Reed Relay Card
50-115A-121
-
This is the 64xSPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 470Ω
50-298-014
-
The 50-298-014 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Compact PCI Multi-function Decommutator
LS-50-cP
-
The Lumistar LS-50-cP 3U Compact PCI Multi-function PCM Decommutator offers the greatest flexibility in the industry by incorporating up to 10 functions typically encountered in flight test applications in a single 3U Compact-PCI card slot. Five functions are achieved on the main board (PCM Simulator which can also operate as a BERT, PCM Decommutator, IRIG Time CodeReader, IRIG Time Code Generator, and the same 5 functions can be achieved on the LS-55-DB Multi-Function Decom Daughterboard. CVSD Voice Decoding and h.261 Video Decoding are achieved through software.
-
Product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
-
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
Product
PCI 39xSPST 2Amp Relay Card
50-132-003
-
The 50-132-003 39xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
-
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
Product
BNC Box-D37M To 16 SE BNC Outputs For 24-Bit PCMCIA DAQ Cards
CB218S
-
*D37M input*16 Single Ended BNC Output Channels*Connects from Ines or Elan 24-bit PCMCIA DAQ cards via CBL-T30-32-D37F cable*Only for DMM i218, AD218 or AD218/i PCMCIA DAQ cards
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
-
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779418-01
-
16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device - The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Flexible MiniPCI Express to Two PCI Express Splitter
SKU-033-21
-
The Flexible MiniPCI Express to two PCI Express Splitter (Splitter) was designed to expand the modern motherboard (ATX, mini ATX, etc.) with a limited number of PCI Express connectors. It allows you to connect up to two x1 or x4 PCI Express add-in boards to the motherboard’s standard MiniPCI Express connector.
-
Product
PCI-8361, PCI Host, 100 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
781394-01
-
The PCI‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8361 card provides a PCI link over a copper cable to the PXI‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
PCI Express, PCI, Multi-Interface Test Backplanes
-
Amfeltec PCI Express, PCI, Multi-Interface Test Backplanes
-
Product
PCI Programmable Resistors
-
Part of our Sensor Simulation family, these PCI programmable resistor cards are ideal for medical, aerospace and automotive applications.
