PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
Product
PCI Card with input channels
PCI_LVDS_8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
2-port/4-port GigE PCI Express Card
AX92322
-
The AX92322 is a GigE compliant PCI Express card supporting two or four independent Gigabit Ethernet ports. It features PCI Express x4 interface and has four powerful independent Intel® Ethernet Controller i210-AT. The GigE frame grabber card supports 9.5KB Jumbo Frame and IEEE 1588 to enable faster and more accurate throughput of data. The AX92322 is built for machine vision and surveillance applications in industrial IoT field. This PCI Express frame grabber card is designed to help customers develop and deploy machine vision and surveillance applications which will greatly benefit through reduce the cost and simplify system integration. Moreover, the AX92322 has a wide operating temperature of 0˚C to 70°C, making it suitable to be used in most server environments. The advanced GigE frame grabber runs on Windows® 7, Windows® 10 and Linux.
-
Product
Industrial Grade PCI DIO 96 Board
MS 1817
-
*96 digital input/output lines*Support s all PPI Modes (Mode0, Mode 1 and Mode 2)*5 V TTL/CMOS*Compatible with NI DIO Card*2-wire handshaking capability*Known power-up
-
Product
PCI Very High Density Multiplexer, 10-Channel, 16-Pole
50-670C-022-10/16
Multiplexer Module
The 50-670C-022-10/16 is a 10-channel, 16-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
Processor Intel Core I7, PCI Gen 3, AMC
AMC726
-
The AMC726 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® 4th generation Core i7 Processor (Haswell) with QM87 PCH. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
Product
Low Profile PCI Express 8-Port
7803ec
-
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
Product
PCI Express Mini Card
mPCIe-UCAN2 & mPCIe-UCAN2-ISO
-
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
Product
PCI Express PMC Carrier
TPCE260
-
The TPCE260 is a standard height PCI Express Revision 1.1 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control.
-
Product
PCI Express
PCIe
-
PCI Express (PCIe) has become the leading interconnect technology to succeed the Peripheral Connect Interface (PCI) architecture. The PCI Express(PCIe) architecture retains the PCI usage model and software interfaces for investment protection and smooth development migration. The technology is aimed at multiple market segments in the computing and communication industries, and supports chip-to-chip, board-to-board and adapter solutions. PCI Express 5.0 currently runs at 16GT/s or 32Gbps per lane in each direction, providing a total bandwidth of 128GBps in a 16-lane configuration which is the largest size in use.
-
Product
PCI Express Bus Analyzer / Exerciser / Endpoint
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
PCI Very High Density Multiplexer, 10-Channel, 8-Pole
50-670C-021-10/8
Multiplexer Module
The 50-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
-
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
Product
PCI 4-Input Frame Grabber
611
-
Color or monochrome: PAL, SECAM, NTSC, RS-170 compatible 4 composite video inputs or 3 composite and one S-video 8 TTL I/O lines for camera control Programmable AGC, hue, contrast, saturation Optional enhanced SDK for Windows 98/2000/NT/XP/CE Optional Linux and QNX drivers
-
Product
PCI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
50-635A-003
Multiplexer Module
The 50-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
PCI Express Control of PXI Express
PCIe-PXIe-8638
Extension Kit
The PCIe-PXIe-8638 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. With comprehensive hardware and software transparency, the expansion kit enables fast and convenient detection of any PXI cards installed in the system, requiring no additional drivers or software.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm
50-293-011
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
PCI Express Graphic Card with NVIDIA® Quadro® P2200
Quadro-E PEG P2200
Graphics Card
The Quadro-E PEG P2200 perfectly balances performance, features, and compact form factor to deliver exceptional creative experience and productivity across a variety of 3D applications. The Pascal GPU with 1280 CUDA cores, 5GB GDDR5 onboard memory and support for up to four 5K (5120x2880 @ 60Hz) native displays accelerate product development and creation workflow demanding fluid interactivity for large, complex 3D workpieces.
-
Product
PMC-to-PCI Express Adapter
4733
-
The Technobox, Inc. P/N 4733 PMC-to-PCI Express Adapter permits the use of a single-wide PMC module in a 4X PCIe slot. The product features a PEX8114 bridge running in transparent mode. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card. 64-bit support.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 3k
50-265-104
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PCI CONET Controller
A2818
-
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm
50-293-024
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PMC to PCI Express Adapter w/ TSI384
6083
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
-
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
Laser Board
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
Flexible 32-bit PCI to MiniPCI Express Adapter
SKU-057-0X
-
The Flexible 32-bit PCI to MiniPCI Express Adapter (Adapter) was designed to convert the 32-bit PCI bus into a MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion board to the motherboard PCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), 32-bit PCI host board and PCI Express flat cable.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 3.55kΩ
50-297-023
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
-
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
