D/A Converters
Transform digital signals to analog.
-
Product
Ethernet To Fiber Optic Converters (Point To Point)
-
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
DC/DC Converter 192 W
HP2540-9TB1G
-
DC/DC converter with 192 W from Bel Power Solutions | input ranges 16.8 - 137.5 VDC | two outputs at 15 V | operates in temperatures from -40 to +71 °C | provides 10 ms hold up time | 20 mm heatsink included
-
Product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
-
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
Product
Converter Signal Amplifier – 0…10 Vdc – DIN Rail
HD978TR4
-
Configurable signal converter amplifier with 0…10Vdc (10…0Vdc) output. Input range -10 ..+60 mVdc. Standard configuration 0…20 mVdc.
-
Product
ARINC 818 to DVI Converter
-
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
Product
CAN + OBD Network Data Converter
NC2
-
Add Vehicle Network based Data Acquisition to your existing fleet data acquisition systems for under one thousand dollars with the NC2. Great for NVH Tachometer applications.
-
Product
Antenna Impedance Converter
-
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
Product
Compact Converters
-
Virginia Diodes offers compact converters (CCs) for frequency up and down-conversion. These converters are easy to use and well suited for high performance up and down conversion of wide band modulated millimeter-wave signals. VDI CCs offer full waveguide band coverage and are available from WR28 (22.5-40 GHz) to WR2.2 (330-500 GHz) with additional CCs under development. Compact converters can typically be delivered within 9-11 weeks ARO or less. Contact VDI for more information.
-
Product
Integrated Frequency to Voltage Converter
FV
-
The FV6 Frequency to Voltage Module provides a convenient method of converting up to six frequency signals to analog voltages that can be fed into common data acquisition equipment.
-
Product
Protocol Converters
-
Applied Systems Engineering, Inc
ASE provides a total solution approach to the area of protocol test equipment with its’ family of PC based protocol test products. The ASE2000 RTU Test Set is a full-featured protocol test unit that provides the user with a powerful and flexible tool for testing and maintaining SCADA RTU and SCADA IED equipment and diagnosing communication problems.
-
Product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
DC/DC Converter 140 W
CTS-120-6875-D
-
DC/DC converter with 140 W from Premium | input ranges 43.2 - 90 VDC | output 24 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
Power Divider Combiner, 2 Way, SMA RF Splitter for Distributed Antenna Systems (DAS)
PD2120
-
INSTOCK Wireless Components, Inc
Ideal for DAS (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Digital-To-Analog Converters
-
Teledyne e2v has been innovating data converter technologies for over 20 years and offers some of the most powerful digital to analog converters on the market that feature:Signal generation of up to 7 GHzLatency as low as 1 nsFull scale step response times as low as 40 psLowest noise vs. performance on the market at microwave frequenciesThe cutting-edge technology packed into Teledyne e2v's data converters allow our customers to significantly simplify designs with licence free, standard and customized solutions.
-
Product
Transition Time Converters
-
These converters have been designed to convert the transition times of instruments with fixed, fast transition times, to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns); hence reducing the signal bandwidth. All transition-times are between 10% and 90% of amplitude.The design of these converters ensures very low signal reflection far beyond the 3 dB point. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with two SMA connectors, one male, one female.
-
Product
20-50,000 Hz Charge Amplifier
203G8
Amplifier
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
Product
AC/DC Converters
-
Start-Power manufactures single and three-phase unidirectional analogue AC-DC Converters and single and two-directional three-phase digital AC-DC Converters. One- and three-phase unidirectional analogue AC/DC Converters can be used as motor controls or as power supplies in sizes from 40A up to 500A. Three-phase uni- and bidirectional digital AC/DC converters are suitable for speed and torque control of motors.
-
Product
Lightweight, Compact, Fully Enclosed/Shielded Power Converters
Series RKE
-
These lightweight (less than 7 lbs.), compact (less than 160 cubic inches), fully enclosed/shielded power converters deliver either 24, 36 or 48 volts d-c, to run distributed power systems, motors, actuators or heaters. Their universal a-c input (85-265V a-c) is at home with either 115V a-c or 230V a-c, though they produce significantly more output at the higher input voltage, and should be run from 200-240 volt mains wherever possible.
-
Product
Serial Converter
USB-COMi
-
The USB-COMi is a USB to RS485 serial converter. It allows easy serial port expansion without requiring IRQ, DMA, or I/O port resources. The converter allows the user to easily and economically connect RS485 devices to a host using USB. The RS485 communications standard is used by DGH sensor based data acquisition modules and many industrial control devices.
-
Product
Indoor DAS Transmitters
-
Berkeley Varitronics Systems, Inc.
Lightweight DAS transmitters and high-speed receivers for the build-out, optimization and indoor coverage studies of in-building microcell networks and base station repeaters.
-
Product
Miniature Airborne Communications Converter
MACC II - Converter
-
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
Product
WIFI Converter
-
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
Product
Thermal Voltage Converter
1395B
-
The 1395B TVC. Has better thermal stability than it's predecessor. Measuring ac voltages between 20 Hz and 100 MHz with increased accuracy and reliability. The 1395B can be used as a primary ac voltage standard and/or standard for the calibration of ac calibrators and voltmeters.
-
Product
DC-DC Converters (Up To 750 Watt/Module)
A63
-
La Marche Manufacturing Company
The unique design of the LaMarche A63 Series DC-DC Converters will allow you to utilize your 48V, 24V, and/or 12V equipment at a site where 130V batteries are installed. This will save battery, charger, and installation costs as well as reducing maintenance time and optimizing space. The A63 is a compact self contained DC-DC Converter that provides the Modular Power that today's utility substation, process control and telecommunications applications require. The A63 is the building block of these reliable systems using advanced switching technology. Its filtered output provides the clean power required for sensitive loads. The A63 DC output is available in 48V(15 amps) and 24V (30 amps) rated at 750W, or 12V(30 amps) modules rated at 375W.
-
Product
Scalar Mixer / Converter Measurements
S97082B
-
The S97082B scalar mixer/converter measurements enables the highest accuracy for scalar conversion–loss/gain measurements with a simple setup and calibration
-
Product
Electrochemical Converter
C800
-
The Control 800 series of electrochemical converters combines high performance digital conductivity and analog pH measurements with intuitive operation. It has been designed for easy integration into skids and panels to cover a wide range of bioprocess applications in both, conventional stainless steel and single-use systems.
-
Product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
-
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
Product
14-Bit, 2.6 GSPS, JESD204B, Dual Analog-to-Digital Converter
AD9689
-
The AD9689 is a dual, 14-bit, 2.6 GSPS analog-to-digital converter (ADC). The device has an on-chip buffer and a sample-andhold circuit designed for low power, small size, and ease of use. This product is designed to support communications applications capable of direct sampling wide bandwidth analog signals of up to 5 GHz. The −3 dB bandwidth of the ADC input is 9 GHz. The AD9689 is optimized for wide input bandwidth, high sampling rate, excellent linearity, and low power in a small package.
-
Product
DC/DC Converter 2 W
R2SX-2424-R
-
DC/DC converter with 2 W from Recom | input ranges 21.6 - 26.4 VDC | output 24 V | operates in ambient temperature from -40 to +100 °C | tape and reel packaging
-
Product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.





























