Product

Color Matching Booth

-

Unuo Instruments

Unuo Instruments

GSM Round Cutter is used to test material grams per square meter. It would cut sample to 100cm2 cutter, depth max 5mm. Normally, GSM cutter is suitable to cut textile fabric, leather, paper and etc. It has four double-sided blades, and the blade is evenly distributed in four equal parts. The blade can be replaced. GSM Testing is essential for some tests like Matindale abraison test meet standard ISO20344.

Product

PC/104 FFT Processor w. Virtex-5 FPGA

SMT105-FMC

-

Sundance Multiprocessor Technology Ltd.

SMT105-FMC - Sundance Multiprocessor Technology Ltd.

The SMT105-FMC can be used either as an I/O-Blade for a Single Board Computer with either the OneBank or Three-Bank PCIe/104™ Connector solution or used as a “Head-Less” solution, ie. Remote Host Controlled.

Product

High and Low Temperature Humidity Chamber

GDJS/GDJW

-

Lisun Electronics Inc.

GDJS/GDJW - Lisun Electronics Inc.

•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃  Humidity ≤85%R.H

Product

6U Processor Blade

CP62007

-

LinkedHope Intelligent Technologies Co.,Ltd.

CP62007 - LinkedHope Intelligent Technologies Co.,Ltd.

CP62007 is a 6U processor blade based on Intel’s 4th generation core i7/i5 processors using 22nm process technology, supporting up to four cores / eight threads at 2.4GHz. CP62007 supports up to 16GB onboard soldered low voltage DRAM with ECC. It also offers up to 64/128GB SLC/MLC onboard SATA SSD for installing operating system and drivers. The onboard design of memory and SSD enhance the anti-shock and vibration performance dramatically.CP62007’s onboard processor integrates Intel® HD Graphics 4600 controller, supporting a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA. And the VGA resolution is up to 2048x1536. With HDMI/DP/eDP outputs, the resolution can be up to “4K”.CP62007 supports 1x VGA and 2x DP/HDMI/DVI, up to 3 independent or cloned displays.CP62007 uses high speed CPCI connectors on J3 and J4 position for transferring high speed serial signals, such as PCIe2.0, USB3.0 and SATAIII. And the foot-print of high speed connectors are fully compliant with CompactPCI specifications.

Product

Impact Tools

D814™ Series

-

Fluke Networks

D814™ Series - Fluke Networks

Make effortless, uniform connections with Fluke Networks’ D814™, all-in-one, telecom punchdown tool. Its adjustable impact wheel has high and low settings for any type of termination. Automatic spring mechanism provides right impact to seat and/or terminate wires. Compartment at the end of the tool stores an extra blade.

Product

Quantum-Safe Security

CN8000 Series

-

ID Quantique SA

CN8000 Series - ID Quantique SA

The CN8000 harnesses the power of quantum mechanics to help ensure secure communications – the encryption keys are generated by IDQ’s Quantum Random Number Generator to guarantee inherent and provable randomness. The CN8000 can also be upgraded to be quantum-safe via the Cerberis QKD Blade (quantum cryptography) to ensure long-term protection of the data in transit.

Product

3U CompactPCI-Serial

-

Advantech Co. Ltd.

Advantech Co. Ltd.

Advantech offers 3U CPCI-Serial CPU blades, I/O blades and AC/DC power modules to build up solutions in railway, semiconductor, healthcare markets.

Product

ATCA I/O Rear Transition Module (RTM)

ART002

-

Vadatech Inc

ART002 - Vadatech Inc

The ART002 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe, USB and Management I/O for the front blade.

Product

Compact PCI Intel Xeon D Server Blade

CP6006-SA

-

Kontron AG

CP6006-SA - Kontron AG

CP6006 is a server class CPU platform, designed and produced in Germany. CP6006 is based on the 14nm technology Intel® Xeon® D-1500 processor with 8 CPU cores (options 2–16 cores), with excellent performance-per-watt values. Its scalable power budget allows users to tailor the power dissipation to their requirements. CP6006-SA provides cooling mechanics for standard air cooled systems.

Product

Smart Water Meter

-

YOUNIO

YOUNIO

The water enters the meter from the inlet of the meter body and impacts the vane wheel at the tip of the vane blades to make it rotate. The water flows out from the outlet of the body. The rotation of the vane wheel (proportional to the velocity of water flow) is transmitted directly to the central gear in the vacuum-sealed register by the magnetic coupling. The sealed register totalizes and indicates the water volume passing through the meter.

Product

Portable Anemometer

ATS-0345-1

-

Advanced Thermal Solutions, Inc.

ATS-0345-1 - Advanced Thermal Solutions, Inc.

The ATS-0345-1 is a portable vane anemometer for measuring air flow speed and volumetric flow rate. The rotating blades create a frequency proportional to the wind speed. This frequency is accurately converted to speed with 0.1 m/s accuracy. The compact and ergonomic design allows the ATS-0345-1 to be portable, the anemometer's hard plastic carrying case makes transport and storage easy.

Product

Multi-Tester

GWRMT001

-

Grand Wing Servo-tech Co., Ltd.

GWRMT001 - Grand Wing Servo-tech Co., Ltd.

◆To measure the Pulse Width transmitted by Transmitter for up to 9 channels. ◆To measure the Pulse Width sent from Receiver.◆To test the rotations of Servo automatically – at the pulse widths of top, medium and low points set by user already.◆To test the automatic rotations of Servo.◆To test the rotations of Servo by turning the knob on the tester manually .◆To test the sensitivity of Servo (1μS per step minimum).◆To measure RPM of a spinning propeller – for 2 – 6 blades ones, real time RPM value shown／to set the peak RPM value up to 99990 per minute.◆Shiny 4 digits red LED's to display the values measured.◆Power source can be from UM-4 / AAA cell x4, or an adapter with 7-15V or BEC (5V) from an ESC.◆An output port for applying Positive/Negative signals of Pulse Width from this tester.◆Four buttons for setting up functions and modes.

Product

Tachometer & Anemometer

-

ZhangZhou Weihua Electronic co.,ltd

ZhangZhou Weihua Electronic co.,ltd

a Tachometer (measure RPM of turbine blades) and an Anemometer (measures wind speed).

Product

Probe Card PCB's

-

Dynamic Test Solutions

Dynamic Test Solutions

DTS offers both generic and custom PCBs blanks for probe cards. Probe card PCBs are available for all tester platforms and can be configured for any vertical technology, epoxy cantilever and legacy blade cards. DTS probe card blanks are made to precise specifications required for all probing technologies and are available in high speed and high temperature materials. All probe card PCBs employ a balanced layering construction to maintain tight flatness specifications and minimize warping, allowing good probe planarity. Gold plating on all surface metals facilitates easy soldering and minimizes probe resistance. DTS is continually adding new probe card blanks to its library!

Product

20-Port PCI Express

PEX 8680

-

Broadcom Limited

PEX 8680 - Broadcom Limited

The ExpressLane™ PEX 8680 device is the industry's first PCIe switch to offer 80 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 20 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 80-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.

Product

VPX / OpenVPX Chassis

-

Kontron

Kontron

VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.

Product

Rugged Blade Processor W/ Dual Xeon E5

ATC126

-

Vadatech Inc

ATC126 - Vadatech Inc

The ATC126 is a high performance ATCA processor blade featuring dual 14-core Intel® Xeon® processor (E5-2658 v4, E5-2680 v4, E5-2648L, 2618L, 2620 or 2630 v4), with up to eight banks of 256 GB DDR4 memory with ECC. Versatile connectivity includes two 10/40GbE Fabric Interfaces, dual GbE Base Interfaces, dual front panel GbE egress Ports, front panel dual RS-232 and USB 3.0/2.0 Ports and front panel DVI-I connector.

Product

6U VME Server Class Blade Computer

VM6062

-

Kontron AG

VM6062 - Kontron AG

The VM6062 is a low power 2-Core/4-thread Intel® D1508 version of a pin compatible 6U VME SBC products range featuring a processor from the Server Class Intel® Xeon® Processor D-1500 family.

Product

Modular Matrices

-

Smart-e Ltd.

Smart-e Ltd.

Modular Matrices include two ranges: - The LDX+ range provides a cost effective modular solution for budget sensitive projects requiring fewer advance features at shorter Cat 6 cable lengths of up to 70m.- The MDX+ range incorporates the videowall processor technology which allows a number of output blades to be grouped together to form a multi display video mosaic or wall. This feature is available for the HDBT, DVI, 3G-SDI and fibre output cards.

Product

Additional Rotary Axis for High Precision Co-ordinate Measurement Machines, ISO 10360 Part 3 Compliant

QuadDualPurpose

-

Rotary Precision Instruments UK Ltd

QuadDualPurpose - Rotary Precision Instruments UK Ltd

Precision rotary axes specifically developed to increase the flexibility, productivity and efficiency of your CMM.Versatile system with the option to mount parts both horizontally and vertically for inspection, such as large turbine blades from the front of the engine.

Product

Strain Measurements and Experimental Stress Analysis

-

M+P International

M+P International

Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.