Bit Synchronizers
-
Product
120 GBd High-performance BERT
M8050A
-
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Synchronous Generator
ZET 7090
-
Synchronous generator ZET 7090 is used for signal forming of sinus, implulse and saw-tooth shapes and has 2 synchronous channels. Generators can be used independently or within automation and control systems.
-
Product
Multi-Channel Synchronization Module for M8195A
M8197A
-
Synchronization Module for up to 4x M8195A Arbitrary Waveform Generator units.
-
Product
Time Synchronization Card
PMC/XMC
-
IXI Technology’s highly-accurate card provides time down to 62.5ns resolution in UNIX format. Its time-sourced, disciplined, voltage-controlled crystal oscillator (VCXO) or optional CSAC not only allows it to provide sub-second resolution, but also to “flywheel” during the absence or loss of carrier. The module has a status LED that indicates when the internal time is synchronized with the input time code. The card provides a programmable offset on its internal time from the input time source. The generated IRIG-B or 1588 output can be configured to be synchronous to the chosen input time source or configured to use the best available time source.
-
Product
Clockand Trigger Synchronization Board
CLKSYNC-PCI
-
CLKSYNC-PCI is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI is designed for use with multi-channel, ADC and DAC systems where clock and trigger synchronization are required.
-
Product
GPS Synchronized Clock Systems
-
Signals & Systems India Private Limited
GPS synchronized clock system offers accurate time to all clocks in the system. The GPS clock synchronization system consists of a master clock and multiple slave clocks. The master clock communicates with all the salve clocks via wired/wireless medium in the system to provide them with an accurate time source. The objective of the GPS synchronized clock system is to make sure that all clocks in the system display the same time. Regardless of which part of the building you are in, the time shown by the clocks will be uniform and accurate.
-
Product
Synchronization and Distribution Amplifier - PCIe
Model 7892
-
The Model 7892 High-Speed Synchronizer and Distribution PCIe Board synchronizes multiple Pentek Cobalt or Onyx boards within a system. It enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP, and software radio applications
-
Product
Clock And Trigger Synchronization Board With Atomic Clock
CLKSYNC-PCI-AC
-
CLKSYNC-PCI-AC is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI-AC is designed for use with multi-channel, ADC and DAC systems where precise clock and trigger synchronization are required.
-
Product
Bit Error Rate Testing
BERT
-
An invaluable tool for manufacturing, development engineers, and field service engineers*Generate multi-speed, multi-application, and custom test patterns*Verify and validate lowest level connectivity down to 10-12*Support up to 32 ports of testing
-
Product
Bit Error Rate Tester
iBERT Series
-
Provide a range of signal conditioning and BER analysis from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry''s broadest serial communications test portfolio of bit error rate tester products.
-
Product
Synchronous Generator
ZET 7190
-
The Synchronous generator ZET 7190 is intended for generating sine, pulse, saw-shaped signals. It has 2 synchronous channels and can be used individually, or as a part of control and automation systems.
-
Product
14 Bit ADC Card
FMCADC100M14B4CHA
-
Sundance Multiprocessor Technology Ltd.
The FmcAdc100M14b4cha is a 4 channel 100MSPS 14 bit ADC card in FMC (FPGA Mezzanine Card) format. By default it uses only signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5V, +/-5V. An advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range of +/- 5V that is independent on the chosen gain range.
-
Product
Bit Error Rate Tester
100G NRZ BERT
-
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
Product
NRZ Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
Product
GPS Synchronization
PGPS04i
-
The PGPS04i is a multiple-functional time synchronization device that integrates with GPS time synchronization, IRIG-B outputs (DC-TTL/DC-RS422/optical), IRIG-B pulse input (DC-TTL/DC-RS422/fiber), 1PPS/1PPM pulse output DC- TTL/DC-RS232/fiber), timing set of whole trigger points, real-time clock auto-generating and other relevant functions.
-
Product
ACC-188 Synchronous Serial Radio Adapter
-
The ACC-188 synchronous serial radio adapter is interoperable among various tactical radio brands and models used by the defense community. The ACC-188 works with any radio that has a synchronous serial communication port using MIL-STD-188-184 and enables the tactical radios to send data such as GPS maps, images, coordinates, and IM-type communications.
-
Product
IMS - Modular Synchronization
-
Meinberg Funkuhren GmbH & Co. KG
The IMS series (Intelligent Modular Synchronization) from Meinberg offers redundancy for synchronization sources and power supply in combination with a highly modular slot-based housing, which also supports hot swapping and scaling options in the field.
-
Product
16 Bit Waveform Generator
PA72G16400
-
The PA72G16400 is a 16-bit arbitrary waveform generator, capable of generating waveforms at speeds up to 400Msps. The high resolution and the high sample rate allows generating signals with very low quantization noise levels. An onboard offset voltage source allows generating offset signals while maintaining optimal utilization of the DAC’s digital range. With the 8MWord of memory, there is lots of room for uploading several different patterns, allowing switching patterns with minimal bus communication.
-
Product
20 Bit Dual-Channel Reference Source
DRS20
-
The DRS20 is a dual-channel reference source offering ultra high precision and stability and provides a +/-10 V output. The output current can be up to 10 mA and the 4 wire connection provides a 1 µV/mA load regulation. The high precision and stability is achieved by using a temperature controlled voltage reference.
-
Product
High-Speed System Synchronization and Distribution Amplifier - 3U VPX
Model 5903
-
- Multi-board synchronization with Quartz RFSoC video- Synchronizes up to 64 channels across eight Quartz® boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions
-
Product
Clock And Trigger Synchronization System
CLKSYNC-40
-
CLKSYNC-40 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
-
Product
16 bit, 125 MS/s PCI Digitizer
ATS660
-
ATS660 has been designed from the ground up for OEM applications, which require very high reliability, high performance, high quality and reasonable prices. ATS660 uses COTS analog components and FPGAs to provide you more features and benefits and at the same time reduced manufacturing costs without compromising quality. The result is that you get more digitizer for less money.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-50
-
CLKSYNC-50 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
Bit Error Rate Testers
FarSync BERT Tester – PCIe
-
A Bit Error Rate 2 port sync line quality tester for a Windows PC/Server with a PCIe slot. The FarSync BERT provides a comprehensive, simple to use, all in one, line testing utility for testing synchronous lines from your PC up to 20 Mbits/s. There are no extra expensive modules to buy to test different line types.
-
Product
Transmission & Synchronization Tester
xGenius
-
xGenius is a nice handheld tester equipped with a large (8 inc) capacitive touch-screen to make easier the analysis and results interpretation. It is 100% suitable for labs or field use because is full equipped (IP/Ethernet/PTP/T1/E1), battery operated, light (1.9kg) and very rugged. The unit is able to test Ethernet/IP networks up to 10Gb/s while supporting master/slave Sync-E/PTP emulation and also has interfaces for T1/E1.
-
Product
Clock Synchronization
-
Analog Devices Clock synchronizers are designed for wired networking applications, providing the clock redundancy functionality needed to maximize system uptime. Our technology supports clock synchronization with common standards, including 1 pulse per second (PPS) output signal from a GPS receiver. GPS signals are broadly available and utilize an extremely stable atomic clock as its time base, but they are often noisy. Systems rely on the IEEE1588 timing protocol to establish synchronous communications across the wired network, including synchronous Ethernet and synchronous digital hierarchy (SDH) to optical transport network (OTN) mapping/demapping. The IEEE1588 protocol has emerged as the preferred method for Clock synchronizing systems throughout both computer networks and local area networks (LAN).
-
Product
Multi Channel Bit Error Rate Tester
QSFP+ Tester Rx
-
You want to save time by measuring sensitivity on all four QSFP+ channels at the same time? Here we go: BERT + E/O converter + optical attenuator + optical power meter.Have this four times in two mainframes. Only one clock source is needed.Covers 16G FibreChannel and Infiniband FDR.
-
Product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
-
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
Product
M-Code Mission Timing and Synchronization
SecureSync
-
The latest generation of modernized security architecture, modernized anti-spoofing and anti-jamming for GPS-degraded environments, operations in mixed P(Y)-code and M-Code constellations, accelerated Direct-Y and Direct-M code acquisitions, and Over-The-Air-Rekeying (OTAR). SecureSync M-code provides better than 41 dB J/S while tracking and better than 54 dB J/S while providing cryptographic key retention without battery backup.
