Host
-
Product
Flexible x1 PCI Express to MiniPCI Express Adapter
SKU-056-02
-
The Flexible x1 PCI Express to MiniPCI Express Adapter (Adapter) was designed to convert the x1 PCI Express bus into the MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion add-in board to the motherboard PCI Express connector.The Adapter includes a MiniPCI Express adapter board (downstream), x1 PCI Express host board and PCI Express flat cable.
-
Product
cRIO-9055, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller
787043-01
Embedded Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9055 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
CompactPCI
cPCI4IP
-
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
Product
MXI-Express Cable, Gen 2 x8, Copper, 5m
782317-05
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Cloud, Networking & Servers
-
Refers to the hosting or using of network services via a public, private, or hybrid cloud.
-
Product
64-bit/66 MHz Metering PMC-to-PMC Extender
3954
-
The extender/analysis probe permits extension of a PMC card beyong the edge of a host processor front panel, providing access to both Side 1 and Side 2 of a PMC under test.
-
Product
PCIe to SD 3.0 M.2 Module
-
The M.2 module is based on Artix-7 FPGA that provides bridging features between PCIe and SD3.0 units to validate different memory densities of micro-SD card. For host processor communication, the module is designed with 2-Lane PCIe Gen 2.0 interfaces. The module presents compact design, flexibility, and consumes low power. Since PCIe is backward compatible with the earlier version the user can integrate into existing systems with ease. The interface towards the SD card is realized by the SD protocol implemented in the FPGA.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device
781630-07
GPIB Controller
Ethernet GPIB Instrument Control Device - The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Cloud-Based Workflow And Asset Management
VeSion™ R-Server
-
Part of VeEX’s VeSion™ centralized monitoring and management solutions, the R-Server Workflow and Asset Management system provides crucial tools to manage fleets of technicians, test equipment, standardized test profiles, thresholds, centralized test results collection, reporting, jobs/ticketing, and software update delivery to create coordinated and efficient disciplined workforce and test procedures. R-Server enhances the workflow to achieve the level of quality and repeatability required by telecommunications service providers, MSOs and their contractors. The flexible R-Server can be deployed in cloud, hosted, and corporate networks, on physical or virtualized servers.
-
Product
Multi-Interface Frame Grabber
Xtium2 CLHS PX8
-
Building on the field proven Teledyne DALSA’s Xtium family of frame grabbers, the Xtium™ 2 CLHS PX8 features CameraLink HS standard on the PCI Express™ Gen 3.0 platform. The Xtium2-CLHS supports Active Optical Cable (AOC) and industry standard CX4 cables. This single cable, single slot solution supports up to 7-CLHS lanes, each operating at 10.3 Gbits/s, to acquire images at up to 8.4 GBytes/s and transfer them using PCIe x8 slots to the host memory.
-
Product
Fluorescence Multiphoton Microscopy
Ultima Investigator™
-
As the most streamlined model of Bruker''s Ultima family of multiphoton microscopes, Ultima Investigator™ features a base system specifically optimized for in vivo studies and is designed for add-on flexibility with a host of specialized options. Ultima Investigator''s high-resolution, high-speed, high-sensitivity deep imaging provides the ultimate value for smaller labs and additional imaging bandwidth in larger labs.
-
Product
Virtex 7 FPGA Carrier
PC7: 330/690
-
The PC7 family of FPGA carrier boards is DEG’s latest AMD-based product innovation. With the ability to host two FMCs (FPGA Mezzanine Cards) with rear panel I/O, the PC7 product line sets the benchmark for performance and versatility in the embedded PCIe market. Coupling this flexibility with a AMD Virtex-7 VX330T or VX690T FPGA, the PC7 enables multi-channel high-speed data acquisition and extensive digital signal processing all within a single PCIe slot.
-
Product
PCI Express Board Retainer
SKU-038-0X
-
The PCI Express Board Retainer prevents the host card from wiggling, and allows a PCI Express board to be held in place without a bracket.
-
Product
Ethernet
-
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards (only 64 bit versions). The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.The receive channels allow for the storage of all packets to all MAC and IP addresses with status and Time Tag information appended to each packet. The receivers allow for filtering based on MAC address, IP address and UDP port. The transmit channels enable the user to define a Bus list which controls timing and order of packets without host intervention or immediate mode which enables the host to transmit packets at will.
-
Product
PXIe System Module: Single Port (x8), Gen 3
M9022A
PXI Express Module
The M9022A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The module can also be used with an M9037A PXIe embedded controller to interconnect two chassis in a multi-chassis system.
-
Product
Gateways And Bridges
-
Handle your single X.25 line to TCP/IP migration requirements. The FarLinX Mini Gateway supports XOT to X.25 switching, X.25 to TCP data translation and connection routing, TCP to XOT, a Triple-X PAD, and a Host PAD. The FarLinX Connect Mini v2 offers HDLC Bridging and conversion.
-
Product
Load Pin Products
-
DLM are world renowned for the design and manufacture of custom design load pins for a host of industries, including offshore moorings, renewable energy and marine & subsea applications.
-
Product
Xeon E3-1125 Processor AMC, PCIe
AMC720
-
The AMC720 is a flexible processor AMC for general purpose processing. The AMC720 has quad-core Xeon and Linux support, it can act as system host and data processing engine. The dual front-panel GbE ports provide simple network connectivity, so while the unit is designed for embedded processing (i.e. typically without a monitor), it is straightforward to use with a virtual desktop on a remote PC/laptop for development and setup.
-
Product
Flexible MiniPCI Express to PCI Express Adapter
SKU-035-XX
-
The Flexible MiniPCI Express to x1, x4 or x16 PCI Express Adapter (Adapter) was designed to convert the MiniPCI Express bus into x1, x4 or x16Express bus and extend it. It allows you to connect a x1, x4 or x16 Express expansion add-in board to the motherboard’s MiniPCI Express connector.The Adapter includes an x1, x4 or x16 PCI Express adapter board, MiniPCI Express host board (full-size or half-size) and a PCI Express flat Cable.
-
Product
Three Phase AC Voltage Source
EAC-TAVS
-
Electronic Test & Power Systems
The EAC-TAVS is a series of programmable high power AC voltage sources. Each system provides a three phase true sinewave output as standard. Each unit is built in a freestanding cabinet. The output frequency is adjustable in the range of 45 - 105Hz. Different frequency ranges are optional, with up to 805Hz possible. An RS-232 and CAN interface are provided as standard. The high resolution TFT front panel displays a host of measurement and setting functions. Besides standard models, other nominal power levels and voltages can be user specified. Single phase and bidirectional versions are available on request.
-
Product
Ultrasonic Flaw Detector
MFD620C
-
The MFD620C is an advanced digital ultrasonic flaw detector featuring a multi-color TFT LCD and a host of new features to meet challenging inspection requirements. It combines powerful flaw detection and measurement capabilities, extensive data storage, and the ability to transfer detailed inspection data to the PC via its high-speed USB port.
-
Product
8-Port PCI Express
PEX 8732
-
The ExpressLane™ PEX 8732 is a 32-lane, 8-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8732 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms. The PEX 8732 is well suited for fan-out, aggregation, and peer-to-peer traffic patterns.
-
Product
PCI Express To PCI Express Expansion For Multiple Host Computers
ExpressBox16-SX8
-
Magma’s ExpressBox 16 is the simplest solution to seamlessly increase the number of PCI Express® slots available to your server or workstation. ExpressBox 16 expands one host PCIe® slot to sixteen slots by extending PCI Express signals over a high-bandwidth x8 or x16 connection to an external Magma enclosure.
-
Product
PCIe FPGA Carrier For FMC+, Kintex UltraScale™
PCI592
-
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
Product
18-Port PCI Express
PEX 8733
-
The ExpressLane™ PEX 8733 is a 32-lane, 18-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8733 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
USB Cable
784387-02
USB Cable
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
Product
*C Series CAN Interface Module
CAN Interface
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
15-CH Isolated Digital Output Module
ND-6056
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
EPM Series Dual-Channel Power Meter
N1914A
Power Meter
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
-
Product
cRIO-9038, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller
783850-02
Embedded Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9038 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9038 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9038 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
