Limiters
-
Product
Transient Limiters
-
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
-
Product
Limiters
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a complete line of RF and microwave limiters, LNA/limiters and limiting amplifiers up to 18 GHz. These products use the latest thin-film hybrid manufacturing techniques to obtain the highest levels of performance, repeatability, reliability and cost-effectiveness. Using the latest technology available in the industry for silicon and GaAs FET MMICs, these products are ideal for multi-market and aerospace and defense applications.
-
Product
Compressors & Limiters
-
Applied Research and Technolgy
Take control of your dynamics with our range of compressors, limiters, expanders, and gates.
-
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Power Limiters
-
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Product
Power Limiter, 0.01 to 18 GHz
N9356B
Power Limiter
The N9356B power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
Product
Limiters
-
A limiter catches the loudest peaks of an audio source and applies brick wall compression that prevents it from exceeding the clipping point of 0 dBFS.
-
Product
Analog Limiter
SIM964
-
Stanford Research Systems, Inc.
The SIM964 Analog Limiter provides upper and lower voltage limits for conditioning dynamic signals. Limits are set between ±10 V with 10 mV resolution. Two rear-panel TTL signals are activated when upper or lower limits are exceeded.
-
Product
Harness Design and Manufacture
-
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
Product
Boundary-Scan Interactive Analyzer & Toolkit
ScanExpress JTAG Debugger
Analyzer
Test probe access is a luxury—modern electronic system design techniques such as blind and buried vias or ball-grid-array (BGA) devices guarantee limited signal access. Test points quickly reduce precious board real-estate and can even degrade performance. ScanExpress JTAG Debugger overcomes these limitations to provide the control and visibility necessary to quickly debug and test hardware, using a simple JTAG port to interface with IEEE-1149.1 compliant devices.Whether debugging prototype hardware, enhancing production tests with boundary-scan control, or diagnosing a faulty board in the field, ScanExpress Debugger’s easy-to-use and versatile interface helps engineers test and debug systems faster and more efficiently.
-
Product
Embedded Vision
-
In the industrial environment, especially in digitalized, automated production scenarios, more and more so-called embedded systems are being used. Embedded devices are small, with compact dimensions, highly efficient, and generate little waste heat. Therefore, they are also suitable for limited space conditions. Due to often harsh environmental conditions, they must be particularly robust and resistant to external influences like massive dust accumulation, strong vibrations, and high humidity or even direct contact with water. Typically, embedded devices are handhelds, smartphones, tablets, vision sensors, smart cameras, smart sensors and single board computers. If the systems have integrated machine vision software, they can be used for a wide range of image processing applications. This is known as embedded vision.
-
Product
PXI High Density MUX BRIC, 48-Chan, 20-Pole
40-570-316
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
Product
AC-Powered, AC Voltage Monitor, Adjustable
VMA
Voltage Monitor
NAI’s VMA is a field-adjustable, AC-Powered, AC Voltage Monitor used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits.High and low voltage limits, and "pick-up" and "drop-out" time delay are field-adjustable. The VMA voltage monitor is ideally suited for rugged defense and industrial applications.
-
Product
Bypass Diode Tester
BDT
-
Our bypass diode thermal tester is designed to assess the adequacy of the thermal design and long-term reliability of PV modules bypass diodes, which are used to limit the detrimental effects of module hot spot susceptibility.
-
Product
Retroreflector
10704A
Retroreflector
The Keysight 10704A retroreflector (cube corner) is a measurement reflector for single-beam measurements. It is paired with the Keysight 10705A single beam interferometer and is designed for making limited space, single-axis measurements. If mass is critical, the Keysight 10704A is available without housing as the Keysight 10713C, and for extremely critical mass requirements, the Keysight 10713D 1/4-inch base retroreflector can be used.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
FUSION PTR-TOF Instruments
-
Experience our new FUSION-PTR! Performance beyond limits, highest mass resolution and sensitivities, ppqv-level detection limits, Invion source technology and much more.
-
Product
Pitot-Static Tester
PS-425
-
The PS-425 Pitot-Static tester is a low-maintenance, digital tester that is fully portable. The PS-425 is powered by an internal rechargeable 12 volt battery (included in purchase), which enables the test set to be used completely independent of any external power source. A connector is provided for an external 12 volt DC power adapter (included). The PS-425 incorporates the altitude, VSI, and airspeed in one single display. The PS-425 is designed and priced for non-RVSM markets, and includes two quick-connect hoses, 12 VDC power adapter, calibration certificate, and a limited 2-year warranty. This product is ideal for performing simple go/no-go leak tests, as well as for general use as a low-end pitot-static tester.
-
Product
Safe Discharge Rods
-
These instruments will allow you to conduct the safe damp discharge of the residual charge on the cable / equipment by limiting the discharge current.
-
Product
IPS BEACON
-
The Flowserve IPS Beacon is a data acquisition, logging and visual alert device that monitors process pump health. Mounted atop the pump bearing housing, the intrinsically safe Beacon checks power-end vibration (x-y-z axis) and temperature against pre-set limits, logging this data with a time and date stamp when an alert situation occurs.
-
Product
Economy Combo Tester
780
-
The ACL 780 Economy Combo-Tester measures electrical resistance of wrist straps and heel grounders simultaneously and individually. This is a good alternative for companies seeking a personal auditing station but do not need to save data. Adjustable limits add versatility for ESD managers that may need to modify verification plans.
-
Product
ESD Protection
-
Protection against electrostatic discharges (ESD) is part of EMC Immunity (Electro Magnetic Compatibility) requirements. It is the ability for equipment to properly operate in its electromagnetic environment by limiting the reception of electromagnetic energy that may cause physical damage. ESD can be either conducted under the form of a transient voltage or can be radiated due to its fast rising time: powerful harmonics will generate erratic behavior by the application by coupling with other signals. Printed circuit boards must be protected against the effects of electrostatic discharge.
-
Product
Stealth Vertex Metal Detector
-
Stealth Vertex metal detectors are custom manufactured to suit any inline processing application where space is limited. The ultra-slim Vertex detects metal contaminates in free-falling product prior to final packaging. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 46 W, PXI Programmable Power Supply
779647-11
Programmable Power Supply
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
PCIe Smart Bus Extender
PCIeEXT-16HOT
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system. Enabling rapid production testing and engineering debug, the hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
D-Type Flip-Flops
-
Advanced Science and Novel Technology, Co., Inc.
High speed broadband D-Type Flip-Flop for data retiming with full rate clockExhibits low jitter and limited temperature variation over industrial temperature range6.5ps set-up/hold time capability87% clock phase margin for retiming of data input eyeFully differential CML input interfacesFully differential CML output interface with 400mV single-ended swingSingle +3.3V or -3.3V power supplyPower consumption: 415mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Analog Oscilloscope
PS-1005
-
* 100MHz ALT TRIGGER. * 20MHz LIMIT. * 1mV/DIV SENSITIVITY. * 2nS/DIV RESOLUTION. * DELAY SWEEP * CE, TUV GS, UL, CUL, IEC1010
