-
product
6U Mini Chassis
cPCI395
The cPCI395 mini crate series offers hot-swappable, redundant power supplies in 9 slots, compact but modular designed desktop / 19″ chassis. A front-side-plug high performance DC fan is used for cooling with front to rear air flow. One or two redundant operating plug-in 250W cPCI power supplies provide sufficient power for all applications.
-
product
Thermal measuring instrument
High performance heat flow meter with data logger.Up to 16 sensors can be connected at one time.Connectable with all heat flow sensors.
-
product
Renewable Energy Loggers
Data Loggers measure AC & DC circuits for Renewable Energy installations. Record directional flow of current, determine patterns when your system is importing or exporting to the grid.
-
product
Dual Vapor Gravimetric Sorption Analyzer
DVS Resolution
DVS Resolution’s key feature is the combined ability to precisely control and measure temperature and relative humidity while recording the highest resolution changes in mass. DVS Resolution uses a dry carrier gas typically nitrogen or compressed air for its operation. Digital mass flow controllers regulate flows of dry and saturated gases. Relative humidity is generated by precisely mixing dry and saturated gas flows in desired flow ratios which produce expected relative humidity. In a typical experiment a known concentration of water vapor is delivered over a sample placed inside the sample pan connected to the Surface Measurement Systems Ultrabalance™ measuring realtime mass changes caused by sorption or desorption of water molecules. Prior to sorption measurements, the sample can be in-situ preheated/dried at temperatures of up to 300oC.
-
product
Mobile Retroreflectometer
Laserlux® G7
The Laserlux® G7 is the safe, smart and simple solution to meet this challenge. The Laserlux® G7 provides continuous pavement marking assessment and evaluation within the flow of traffic. It is the only commercially available instrument that does not require a dedicated vehicle or vehicle modifications to operate. Not only does the Laserlux® G7 measure pavement marking retroreflectivity, but it is able to provide additional key metrics like stripe width, location on the road, coverage, and presence, performance and location of raised retroreflective pavement markers (RPM’s, cateyes, road studs).
-
product
Power Analyzers
An instrument that measures and quantifies the rate of power flow in electrical systems.
-
product
Surface Water Absorption Tester
TF167
TESTEX Testing Equipment Systems Ltd.
Specimens are placed at an angle on the base of the apparatus. After water flows down the surface of each specimen, the amount of water retained by each specimen is measured. Six specimens are tested, three on the face of the fabric and three on the back of the fabric. The six observations are averaged to determine the surface water absorption of the fabric.
-
product
Calibrated Leak Standards
LeakMaster is a leader in the industry when it comes to the manufacturing of calibrated leak standards (calibrated leak orifices). Each leak standard is meticulously manufactured to a specific leak or flow rate at a predetermined pressure. The purpose of each leak standard is to teach, or calibrate a leak test program, and allow the leak test instrument to memorize the characteristics of a leaking part. These leaks are also introduced into production parts to simulate a “leaking or failed” part condition. LeakMaster supplies a calibrated leak standard with every leak test instrument, and provides recertification services for all of their leak standards
-
product
Level Indicators
4B has a wide range of radio frequency (RF), rotary paddle and capacitance point level indicators for detecting high, intermediate, or low levels of liquids, powders and free flowing granular solids stored in tanks, bins, silos or other containers. Certain units can also be used as plug or choke detectors in chutes, conveyors and elevator legs.
-
product
Electromagnetic Flowmeter for conductive liquids
Picomag
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
product
Diode Lasers
The large spectral coverage of our diode lasers combined with the compact form factor, direct modulation capability (up to 150 MHz), true off during modulation (>70 dB aspect ratio), and integrated spectral clean-up filters make them ideal for applications in high resolution bioimaging, flow cytometry, optogenetics and quantum technologies.
-
product
Semiconductor Functional Verification Tools
Trek5
Breker’s solutions enable test reuse across simulation, emulation, prototyping and actual silicon, eliminating redundant effort across the development flow. The Breker “Trek” suite solves challenges across the functional verification process for large, complex semiconductors.
-
product
Flow And Differential Pressure Sensors
ACEINNA’s flow and differential pressure sensors are designed to serve the need for mass flow and pressure sensing in multiple applications such as gas meters, process control, HVAC, medical, chemical, food and beverage, etc. We offer two newly launched and announced product lines, the MFC2000 family of gas flow modules and the MDP200 differential pressure sensor.
-
product
Flow Computers
Cox FC30 flow computers service both liquid and gas applications. The FC30 features batching, 40-point flow meter linearization tables, and temperature viscosity correction using Strouhal/Roshko advanced linearization methods and multiple flow and control inputs. Relay outputs are independently assignable for alarms and general purpose warnings. The FC30 has serial communications, both RS232 and 485, and isolated analog and pulse outputs.
-
product
Primary Current Injection Testers
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
product
PoE Tester
PE-100
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
product
Volume Flow Rate & Velocity
Lutron Electronic Enterprise Co., Ltd.
Volume Flow Rate & Velocity Testers by Lutron
-
product
Rotational Flow Demonstration Kit
The rotational flow demonstration kit detects the rotational position using the MCU’s on board data transfer controller (DTC) function, a form of state machine, while the MCU’s core is in stop-mode state. This ensures that the average power consumption is kept as low as possible, with IAV (average current) at 4.5 microampere (μA) and a 32 sample burst per second. The flow demonstration kit senses the flow direction and volumetric flow rate of water and gas, and can also detect reverse flow. The demonstration kit is applied using an active inductive method. Two coils are used to sense the rotational position of a part-metalized disk, and a third coil is used to generate a reference signal.
-
product
Wastewater Samplers – Stationary
The ECD Analyzers range of automatic stationary, refrigerated wastewater samplers consists of three models, the AQUAS200, the AQUA-S320 and the rugged outdoor AQUA-S320H. At the heart of each is the well proven AQUA Sampling Module, a robust and reliable unit proven in thousands of applications worldwide and trusted by users as diverse as food manufacturers, water companies and the Environment Agencies. The air pump vacuum sampling system featured within the AQUA Module provides for an extremely accurate, reliable, representative and repeatable sample. Programming set-up and daily operation have been designed to be as simple and intuitive as possible for the user. Sample extraction can be time based or triggered by external sources such as flow meters, level sensors, pH meters, PLC’s etc.
-
product
Loop Testing
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
product
Environmental, Dairy & Agri-Food
Automated analyzers using either direct-read discrete or continuous flow technologies offer a broad range of tests and capacities for beverages and all types of water analysis, including municipal, wastewater, and fresh and ocean sources. For the production of cultured dairy products, unique continuous pH monitoring solutions provide a complete fermentation profile to ensure culture consistency.
-
product
Current Limiting Resistors
Current Limiting Resistors are designed for limiting the flow of current to some predetermined value and are used mainly to to keep flowing current within certain intervals while controlling the circuit.
-
product
Coriolis or Thermal Mass Flow Meters
The RBCM Coriolis or Thermal Mass flow meter is measurable of liquid, gas, liquid-solid and gas-solid two phase fluid mass flow instantaneous rate and cumulative total and realizes display and remote transmitter of all measuring parameters.
-
product
Wet/Wet Differential Pressure Transmitter
647
Monitor differential pressure in air/liquid flow systems, HVAC automation, pneumatic systems and process control with the Series 647 Wet/Wet Differential Pressure Transmitter. Units are temperature compensated and provide a 4 to 20 mA output signal which can be interfaced with chart recorders, data loggers and computerized monitoring and control systems.
-
product
Gas Mixers
Get the right gas mixture and flow rate using our Gas Mixers for Modified Atmosphere Packages. We offer gas mixers for CO2, Oxygen, Nitrogen, and Argon gases.
-
product
Environmental Testers
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
product
Hydraulic Flow Measurement
ND2
The new electronic NDW 2 inclinometer utilises a modern measurement method based on MEMS technology for gravitational inclination measurement (rotational angle measurement).
-
product
RCD Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
product
Multiple-Input Multiple-Output (MIMO) Sine Test
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic.
-
product
Heat Flux Sensors
MF Series
EKO Heat Flow Sensors are applied to measure the heat flow or thermal conductivity in materials and radiative IR flux emitted by body surfaces. The sensors are suitable for indoors applications, some models made for outdoors purposes and are available in different sizes and thickness. All sensors are extremely flat, which is a big advantage considering the minimum interference with the conditions of the testing area the thermal dynamics. Since sensor foils are relatively flexible those can easy be applied on curved surfaces and can be used in different applications to measure the performance of insulating materials in refrigerators, container walls, pipes, building constructions, etc.
