Control
Known value
-
Product
PXI Remote Control Module
Remote Control
PXI Remote Control Modules allow direct control of PXI and PXI Express Systems through PCs and laptops. You can choose between copper (up to 10 m) or fiber-optic (up to 200 m) cable that connects to PXI or PXI Express modules in slot 1 of your PXI system.
-
Product
PXI Remote Control Interface Modules and Kits
Remote Control
Take advantage of the latest high-performance, low-cost desktop PCs for control of your PXI system.
-
Product
PXIe-PCIe8363 1-Port, 208 MB/s PXI Remote Control Bundle
790067-03
Remote Control
The PXIe-PCIe8363 is a bundle that contains a PCIe-8363 Device for PXI Remote Control, a 3 m high-speed MXI-Express copper cable, and a PXIe-8361 PXI Remote Control Module. The PXIe-PCIe8363 helps you establish a connection between a supported device like a PCI Express-equipped desktop PC and a compatible PXI chassis to remotely control PXI and PXI Express systems through a software-transparent link. The included PCI Express device provides up to 208 MB/s of sustained throughput when cabled to a PXI Express chassis.
-
Product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
Remote Control
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
Product
PCI-8361, PCI Host, 100 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
781394-01
Remote Control
The PCI‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8361 card provides a PCI link over a copper cable to the PXI‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
PXIe-8301, Thunderbolt™ 3 PXI Remote Control Module
785679-01
Remote Control
Thunderbolt™ 3 PXI Remote Control Module—The PXIe-8301 enables laptop control of a PXI Express chassis over a Thunderbolt™ 3 connection. Using a Gen 3 x4 PCI Express link, the PXIe-8301 allows up to 2.3 GB/s of sustained data throughput between the chassis and laptop over a Thunderbolt 3 USB Type-C cable. An additional Thunderbolt 3 port allows for connecting additional Thunderbolt or USB-C devices. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
Quality Control
Sandwich Box
-
Housed in a ruggedized box, the VQC Sandwich Box is a field-proven acquisition unit for testing all aspects of vibrator performance, providing real time display of accelerometer and reference signals during the sweep.
-
Product
Control Module
MOC
-
The MOC is our universal control module for a wide variety of tasks, such as controlling relays in the fixture.
-
Product
Generation Control
-
Schweitzer Engineering Laboratories, Inc.
Safely operating a generating facility requires reliable automation solutions that can integrate with relays, SCADA, and plant controls. With a generation control solution, you will realize operational efficiencies and increased reliability.
-
Product
Reactor Instrumentation & Control
-
Capturing the full potential of nuclear power. Our ultra-precise instruments support the safe, optimized operations of nuclear power plants.
-
Product
Motion Control
-
Welcome to Thorlabs; below you will find links to our selection of Motion Control products, a subset of our entire line of photonics products. Thorlabs’ motion control products are separated into manual and motorized linear and rotation stages, multiaxis platforms, actuators, and controllers. The manual and motorized stages can frequently be configured into 1-, 2-, or 3-axis solutions. Since many of the stages are available in either manual or motorized versions, creating a custom system is easy. For nanopositioning applications like waveguide and fiber coupling, our line of multiaxis flexure stages are ideal. Both the motorized stages and the multiaxis platforms are supported by a complete line of controllers for the various motors and piezoelectric actuators. In addition, we support custom and OEM motion control applications with an extensive line of manual, motorized, and piezo actuators as well as threaded adjustment screws.
-
Product
Control Unit
Epec 3720
-
Need to connect 10 propo valve pairs? Epec 3720 control unit is specially optimized for hydraulic actuator control with a high amount of PWM outputs and feedback pins. Epec 3720 I/O interface is compatible with the previous Epec 2020 control unit and gives an easy upgrade possibility. Furthermore, Epec 3720 comes in the same rugged proven-in-use aluminum housing and reliable connectors.
-
Product
PCIe to PXIe Remote Control Interface Cable, 2m
43-921-200
Remote Control Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
Motion Control
-
The ACE products in this segment enhance the quality of any type of movement. Anyone who wants to raise or lower loads, regulate the feed of an object to the precise millimeter or gently decelerate rotating or linear movements will find the right solution here.
-
Product
Electrical Control Panel
-
We hold expertise in offering wide range of Electrical Control Panel. Our entire product range has high tensile strength and is easy in installation. Our range includes Relay Panel, Transformer Panel, DC Panel, AC Panel, PLC PANEL, and industrial panel. We offer them in varied grades and ensure high strength. Moreover, we offer them in well-defined time.
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
-
Product
Control & Monitoring Systems
-
Haliatech Control & Monitoring Systems provides organizations with a comprehensive set of solutions designed to enhance operational efficiency and reliability. Through its centralized control, users can manage and operate all devices and systems from a single dashboard, whether on-site or remotely, ensuring streamlined operations across multiple facilities.
-
Product
Motionnet Motion Control Modules
-
Motionnet comprises of a high-speed serial communication system that involves Master card and Slave modules. ICP DAS USA has two categories of Slave devices: Digital I/O, and Motion Control. Users' actuators/sensors can be easily connected with our Motionnet devices. Motion control modules work together with either a Servo or Stepping motor. Motionnet communication between a Master and the Slaves devices is based on RS-485 technology (Multi-drop, Half-duplex). This technology provides the advantage of simplifying connectivity of devices between remote distances while still offering high speed. Data transfer for the I/O modules is cyclical and time deterministic, so this mean that Motionnet devices can be used for other numerous industrial automation applications.
-
Product
XMC Display Control Card
XM61001
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM61001 is an XMC display control card independently developed by Linghao Intelligent®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
Product
CONTROL TRANSFORMERS
-
Our control transformers are robust, flexible in design and come with short lead time. Basically an ideal solution for control panel builders who need transformers in a hurry.
-
Product
Motor Control Resistors
-
Post Glover specializes in motor control resistors — the most popular use of our resistors — for severe duty applications. Our resistors make it possible to start and stop extremely powerful electric motors — such as those on cranes, compressors, and pumps — with safety and precision.
-
Product
Automatic Welding Control System
-
The system is designed to move the tractor and position the welding head of the machine, which implements the industrial technology of one-sided automatic welding using the "cross-slide" method with obtaining guaranteed high-quality formation of the top and root of the seam.
-
Product
Induction Style Control Relay
1500
-
A floatless liquid level control system from B/W Controls consists of a relay of the proper type, a holder designed to support one or more electrodes or probes in the liquid container, and the corrosion resistant electrodes themselves.
-
-
Product
Motion Control
-
ICP DAS USA provides a wide range of motion solutions for machine automation systems: PC-based, embedded PAC and remote motion solutions using Ethernet, Serial Communication, Motionnet, EtherCAT or CANopen motion control products for distributed motion control systems.
-
Product
MESA Vibration Control
-
MESA tests are specifically required when the unit under test is too heavy or too big and exceeds the capabilities of a single shaker. In a MESA application, multiple shakers provide excitation to the test specimen in a single axis. Different relations like same magnitude and phase for drives, different phase for drives, different magnitude and phase for drives, can be set for this MESA test.
-
Product
BenchMate Passive- Air Vibration Control
2210 Series
-
BenchMate Vibration-Free Platforms enhance the performance of precision tabletop equipment.The 2210 Series features a Passive-Air design requiring periodic manual leveling.
-
Product
Synchro Control Transformer
SCT-RCT
-
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems.
-
Product
XMC Display Control Card
XM26001
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM26001 is a graphics, image processing and computing single-board computer independently developed by Linghao Intelligent®. It uses the AMD G series APU GX-210HA by default, integrating the CPU, GPU, south bridge and north bridge on one silicon chip.
