Fiber Optic Transceivers
-
product
L Band Satellite over Fiber
Transport L Band signals from Satellite Dish to Receiver over Fiber Cable
-
product
Standard In-door Forward Optical Receiver
HR8636
Hangzhou Huatai Optic Tech. Co., Ltd.
HR8636 with standard configuration is a type of high index and universal in-door forward optical receiver. It adopts Philip optical receiving module. End-grade adopts power-doubling module. Optical connectors and RF connector can be installed at the front panel or back panel.
-
product
Transceivers
Macom Technology Solutions Holdings Inc.
At MACOM we offer monolithic and stereo Doppler transceivers for directional motion detection. Our transceivers are used in a variety of applications such as automatic door openers, ground speed recorders and police radars. MACOM’s transceivers are well suited for high volume applications where small size and reliability are required.
-
product
Modular Optical Modulation Analyzer
M8292A
Optimized for the 400G speed class, the M8292A optical modulation analyzer provides a compact, faceless and rack-mountable test instrument that connects to the optical output of coherent transmitters. It leverages the full feature set of Keysight's vector signal analyzer and optical modulation analyzer software ensuring a known-good customer experience for analyzing complex modulated data signals.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-422
The 40/42-860A-422 is a PXI/PXIe dual insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
product
RGB Digital Fiber Optic Amplifier
CZ Series
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
product
Fiber Tester (ST Type)
21-8683-00
The portable design is easy to carry and operation. 2. Low-cost multi-function is more economical. 3. The multiple LEDs display a clear indication. 4. Power saving automatically and Battery low indication.
-
product
Optical Tables with Quad Tuned Dampers for Ultimate Performance
5300 Series
It features quad-tuned dampers in each corner to provide maximum stability and minimum response to vibration disturbances. Coupled with broadband damping throughout, our proprietary epoxy bonded steel and honeycomb tables assure unsurpassed rigidity and stability for demanding applications. To protect against leaks and spills, the SPILLPRUF® configuration provides a safety barrier between the top skin and honeycomb interior.
-
product
Optical Metrology
Complex measurements can be performed quickly and easily with optical measuring solutions from ZEISS. With a high degree of automation and state-of-the-art sensors, they reduce operating errors and guarantee high measuring accuracy.
-
product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
product
Low Power SNMP AGC FTTB Optical Receiver
BGL3000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai BGL3000 product series, is a low power consumption, high index, with SNMP network management, AGC, full function FTTB optical receiver. 3000 series' shells are structure compact aluminum wall hung (without rain-proof), RF interface vertical output , Nixie tube displaying parameters. BGL3000 band have RF overlay interface, is used for IP/QAM and EOC.
-
product
Fiber optic thermometer systems
TS Series
Micronor now offers a complete range of fiber optic temperature sensors, probes and interfaces for temperature measurement in challenging environments. TS series fiber optic temperature probes offer immunity to RF and microwave radiation along with wide temperature range, intrinsic safety and non-invasive use. The fiber optic temperature probes can operate over -200°C to +300°C (-328°F to +572°C), and withstand harsh and corrosive environments. Typical fiber optic temperature monitoring applications include:
-
product
LXI Dual 8:1 Optic MUX SC Loop-Thru
60-851-222
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, SC/PC Connectors
42-852A-218-M62.5
The 40/42-852A-218-M62.5 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
IRDC Transceivers
Vishay is the world’s leading supplier of infrared transceiver products. Vishay remains committed to the supply of high efficiency, robust infrared transceiver products utilizing the latest in-house design technology. Infrared transceiver products support data rates up to 115 kbit/s per the IrDA standard. The products are designed to meet latest industrial, medical and consumer standards.
-
product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
product
47~862MHz & 950~2600MHz Satellite TV & Analog TV PIN Optical Receiver
HRS-26A
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26A optical receiver, adopting high-sensitivity PIN detector, Taking the technology of frequency division multiplexing, it can receive analogue CATV and SAT-IF signal with the frequency of 47~862MHz and 950~2600 Mhz over single fiber. It can be compatible with any FTTx PON to realize triple-play of analog TV, Digital TV (DBS-C, DBS-T), Satellite TV, Internet and FTTH.
-
product
RS422 Mode SI-module With Optical Isolation
MX422-G
RS422 mode SI-module with optical isolation
-
product
HFC 8 Ways Return Path Optical Receiver
HR2080A, HR2080B
Hangzhou Huatai Optic Tech. Co., Ltd.
HR2080 series HFC 8 ways return path receiver can convert upstream optical signal to RF signal at the head-end and remote control center. 8 independent receivers integrated into a 1RU 19” casing to supply service for HFC network terminal. Receiver's low noise design, -22dBm receive sensitivity can provide service to farther place. There are two versions of this receiver. HR2080A with LCD on the front panel, HR2080B without LCD. All receivers are temperature tolerance type can be installed in any network surroundings including out-door type. Both of these two types can adopt SNMP function which can control the front panel to realize optimization work at the head-end and remote installment.
-
product
PXI Single 2 Channel Fibre Optic LC
40-855-412
These PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of five different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Splitters & WDMs
Wuhan Sunma Technology Co., Ltd.
Optical Splitter is used to split the fiber optic light into several parts at a certain ratio. It is an important component used in Passive Optical Network (PON), therefore also called PON Splitter. There are mainly two kinds of PON splitters: one is the traditional fused type splitter known as FBT Coupler or FBT WDM splitter, which features competitive price; the other is the PLC Splitter based on the PLC (Planar Lightwave Circuit) technology, which has a compact size and suits for density applications. SunmaFiber provides both PLC splitters and FBT coupler splitters for EPON/GPON Systems.
-
product
Saluki SE3001 Optical Chopper (1Hz - 10kHz)
SE3001 Optical Chopper is high-precision optical equipment with its chopper frequencies from 1 Hz to 10 kHz. With the advantage of PID technology and high-quality motor, the frequency accuracy of SE3001 is up to 0.5%. SE3001 consists of a console, a chopper head and a control line. The main function of the console is to control the speed of the motor to achieve the target speed. The chopper head is mainly composed of a base and a motor with a blade.
-
product
Single 2 Channel Fibre Optic Mux SC/PC
40-815-212
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-322
The 40/42-860A-322 is a PXI/PXIe dual insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Optical Measurement Methods and Characterization Services
The Fraunhofer IOF develops optical measurement methods and systems to customer requirements. Key areas include the characterization of optical and non-optical surfaces, coatings, components and systems in the micro and sub-nano range as well as 3D shape acquisition.
-
product
Semrock Optical Filters
IDEX Health & Science offers a comprehensive line of Semrock optical filters. We set the standard in performance, quality, and reliability for the life science, point-of-care, clinical diagnostic, and analytical instrumentation industries. We have applied patented design techniques to create some of the most spectrally sophisticated optical filters on the market. Whether you select from our extensive catalog or we design a custom filter to your exact specifications, you can be confident of our uncompromising quality, reliability, and reproducible results.
-
product
Easycheck Fiber Endface Inspector
CA3002
The integrated style design makes the size compact and operation easy. You are no longer to worry about so many cables between monitor and microscope, greatly saving the time for operation and worktable space, thus creating more productivity. Easycheck have a series different model according to different application, it has photo capture function; for transceiver checking; X、Y adjustable; image auto analysis and judgement, etc. The user can choose the desired model per the requirement.
-
product
Optical Spectroscopy Software
Spekwin32
One of this software''s main goals is the consistent display of spectra coming from different sources. At the moment, about 36 different spectral file types from commercially available spectrometer systems can be read. By using Copy&Paste via the clipboard, arbitrary data can also be introduced into Spekwin32 for fast visualization.
-
product
Laser Microdissection and Optical Tweezers
Laser Microdissection is the contamination-free method for separating and collecting cells of interest out of tissue samples or cell cultures. The isolated pure cell populations are the ideal starting point for specific and meaningful results in your molecular analysis. Optical Tweezers are also a contact-free method that uses a highly focused laser beam to manipulate and sort cells in suspension, for example bacteria.
