Fiber Optic Transceivers
-
product
Optical Transceiver
RJ-11
The next generation of optical transceiver has arrived with the introduction of GCI's RJ-11 Optical Transceiver. This fully SEMI compliant and Hokuyo compatible unit is the choice of leading 300mm FABs and equipment manufacturers throughout the world to simplify installation and maintenance of their E84 communications.
-
product
PXIe-5830, 12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
787047-01
12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5830 supports validation and production test into mmWave frequency bands. This vector signal transceiver incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe-5830 helps you test a variety of cellular and wireless standards such as Wi-Fi 6. You can expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
product
SparkFun Transceiver Breakout
RS-485
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
product
Transceivers
Transceivers implement physical layer protocols for various communications and serial bus interface standards. Maxim’s transceivers integrate a wide array of features to increase reliability and simplify designs while providing the highest levels of protection on the market. Click on the following links for more information about each of our transceiver product lines.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Multi-Mode, 62.5/125 Fiber
40-860A-512-M-HI
The 40/42-860A-512-M-HI is a PXI/PXIe single insert/bypass switch with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Optic Modem
VCH-608
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
product
Optical Fiber Ranger
OFR300
Shanghai Tarluz Telecom Tech Co., LTD
OFR300 Optical Fiber Ranger is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the OFR300 fiber ranger detect fiber faults location more accurate and easy.
-
product
Optical Fiber Identifier
OrienTek Optical Technology Ltd.
Optocal Fiber Identifier Economical Solution for Integrated Fiber Preparation Tool Demand● 4 easy-change chucks for:bare fiber, patch cords & ribbon fiber● Identifies 3 common test tones● Identifies dominant traffic direction, audible alarm● Approximate core power reading● Low false detection & insertion loss● Very easy to operate● Battery low indication
-
product
Fiber Stretchers
We offer the most extensive line of fiber stretchers available in today’s market. It begins with a family of 3 stretcher platforms designed to span a fiber stretch range from 0.14 mm to 6.40 mm (standardized to single mode fiber, applying maximum voltage drive).
-
product
CATV 1310nm Fiber Optic Transmitter
MX862T series
The MX862T series direct modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital information for CATV and/or telephony applications.
-
product
Fiber Optic Test Kits & Sets
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) has selected test equipment that is ideal for the field technicians who install and test our products. We offer a wide range of test equipment that meets our customers needs, including the periodic installer to the rugged field requirements for the US Army and USMC deployed or depot maintenance personnel to the advanced requirements of the Navy Shipboard installer requiring Navy approved test sets.
-
product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
product
Fiber Optomechanics
The versatile FiberBench product line includes Single and Multi-Axis FiberBenches as well as a wide variety of compatible components ranging from beamsplitter modules to wave plate units. FiberBenches form the foundation of a nearly infinite array of miniature fiber optic systems that customers have been building for the last decade. When used with the FiberPort Collimators/Couplers, a complete optical circuit can be constructed. The Fiber Launch Platforms are ideal for coupling a free space laser into a single mode, multimode, or polarization-maintaining fiber. Other accessories include fiber mounts, fixed and kinematic collimator adapters, and L-bracket mating sleeves.
-
product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber
40-855A-322-HI
The 40/42-855A-322-HI is a PXI/PXIe dual 2-channel multiplexer with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Optical Cable Testers
Encompasses the processes, tools, and standards used to test fiber optic components, fiber links, and deployed fiber networks.
-
product
Fiber Optic Inspection Microscope
80761
The Miller 400x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment. Includes 2.5mm universal adapter cap and zipper case.
-
product
Fiber Optics
The Neoptix product line includes fiber optic temperature sensors for transformer windings temperature monitoring and for laboratory, industrial, and medical applications.
-
product
Fiber Optic Type Chemical Solution Concentration Monitor
CS-100F1 Series
The CS-100F1 Series is equipped with fiber optics cable based on the CS-100 Series. It offers real-time, in-line measurements by directly integrating the sample cell into the cleaning system piping and by using a fiber optic cable for light signal transmission. A single concentration monitor can take up to four measurements and monitoring of multiple chemical solutions in a single-bath or single-wafer cleaning system is also possible.
-
product
Ethernet To Fiber Optic Converters (Multi-Drop)
Our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire Ethernet network more robust and reliable. These Fast and Gigabit Ethernet to multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors
42-850A-114-M50
The 40/42-850A-114-M50 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Optical Fiber 32×1 Switch
OFSW - 32 × 1
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 32×1 is a 32×1 prism optical switch. It can support 32 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Multi-Mode, 62.5/125 Fiber
40-860A-212-M-HI
The 40/42-860A-212-M-HI is a PXI/PXIe single insert/bypass switch with SC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Transceiver Driver
S-112
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
product
Digital Video/Audio/Data Optical Transceiver
OD3000A
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD3000A digital series optical transceiver, adopts digital video coding technique and WDM technique to satisfied user's multipath digital video, audio, data, ethernet's long distant high quality optical fiber transmission because of its full-found. Product including single fiber one way digital video, single fiber 64 routes video, 128 routes audio and data uni-direction and bi-direction complication. OD3000A can transmit the camera audio/video signal, camera and tripod head control data as well as other control function to central control room from remote end by optical fiber. It can be widely used in the remote monitoring, video conference, video medical ， remote education and other systems of public road, traffic, industrial and mining, community ect.
-
product
High-speed Fiber Stretcher
PZ1
The PZ1 is the high-speed member of our family of fiber stretchers. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, variable optical delay, general purpose fiber interferometry and large angle modulation of interferometric phase.
-
product
Fiber Optic Inspection & Cleaning
One of the most basic and important procedures for the maintenance of fiber optic systems is to clean the fiber optic equipment.
-
product
Handheld Optical Fiber Ranger
X5005
Fiber Ranger X-5005 is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the fiber ranger to detect fiber faults location more accurate and easy.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber
40-850A-514-M62.5-HI
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
