Fiber Optic Transceivers
-
product
2-channel RF Transceiver Module
FMC30RF
Sundance Multiprocessor Technology Ltd.
The FMC30RF is an FMC Daughter Card which is fully compliant with the VITA 57.1-2010 standard. The FMC30RF offers in a small footprint a low power and fully featured Rx / Tx signal path for the development and deployment of advanced RF solutions. With a frequency range coverage from 400MHz to 3.0GHz* and up to 60MHz* bandwidth the FMC30RF provides flexibility and reconfigurability to a host of applications.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
40-860A-412
The 40/42-860A-412 is a PXI/PXIe single insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Optical Power Meter with Optical Head
GM8012 + 2 X GM8300X
The UC8820 + 2 X UC8820X optical power meter with optical head offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume production line application.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, LC Connectors
42-850A-414-M50
The 40/42-850A-414-M50 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
1550nm High Power Fiber Optical Splitter
HPFS-1550-口口-1×N
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HPFS-1550 series high power fiber optical splitter and adopt special process of fused bi-conical taper technology and good heat treatment. It can be applied by divided high performance and high reliability to multi-port optical power distribution of 1550nm high power laser light source. The maximum pass power is 50W(47dBm).The feature of the product is high stability, high uniformity, low polarization dependent loss and low excess loss.
-
product
Optical Fiber 1×32 Switch
OFSW - 1 × 32
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×32 is a 1×32 prism optical switch. It can support 1 optical fibers input and 32 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-118-M62.5-HI
The 40/42-852A-118-M62.5-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Optic Power Meter
The handheld Fiber Optic Power Meter is a user-friendly tool for engineers testing and maintaining fiber optic systems & networks. Both compact and rugged, these devices can be used for absolute optical power measurements, as well as relative loss measurements. In addition, high accuracy and a user self-calibration function result in an excellent overall value.
-
product
Field Fiber Cleaver
HW-09C
Shanghai Fibretool Technology Co.,Ltd.
The Fibretool HW-09C is a single fiber cleaver designed to accommodate either 900µm buffered or 250µm coated fiber. The HW-09C cleaver's quick and easy three-step operation is well suited for mechanical splice and quick termination field connector applications. The leaf spring base is ruled to allow for cleave lengths of 2 to 20mm. The standard carbide blade will perform up to 6000 cleaves before replacement.
-
product
Fiber Optic Power Meter
Fiber optic power meter is a test instrument used for absolute optical fiber power measurement as well as fiber optic loss related measurement .This hand held type fiber optic test equipment features ingenious appearance,wide range of power measurement, high accurate test precision and user automatic self calibration function. Fiber optic power meter is a tool for telecom and CATV network.
-
product
Optical Access
CXR offers a choice of conversion and optical transport Ethernet or TDM streams, and CWDM optical multiplexing.
-
product
Optical Switch
5504
The FOD 5504 Optical Switch is a unique handheld instrument for calibration sets and measurement automation. Routine comparison with Master device procedures in calibration laboratories, can be simply performed with before unachievable repeatability. No more need to move fiber and connect it repeatedly. Fix cables on a table, only once clean and connect patchcords.
-
product
Optical Fiber Tensile Jig
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, MU Connectors, With Interlock
42-850A-314-M62.5-HI
The 40/42-850A-314-M62.5-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Bragg Grating And Optical Filters
Exail is committed to develop and manufacture optical components with excellent performances to support the most diverse industrial applications such as Telecom, sensing, defense, space, fiber laser and harsh environment.
-
product
Optical Inspection
3D AOI
In contemporary electronics manufacturing, automatic optical inspection (3D AOI) is an established component of quality control. A company purchasing a 3D AOI system wants to ensure that it is manufacturing its electronic products in the very best quality and can guarantee they will have a long service life. The Viscom systems feature superlative 3D and software attributes to deliver excellent measurement accuracy and exceptional image quality. Our 3D AOI systems are designed for simple programming and can also be flexibly adapted to new requirements, allowing them to easily accommodate fast product changeovers as well as large production quantities.
-
product
Optical Fiber Cable Testing Equipment
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
product
Fiber Optical Cabling
An optical fiber, or optical fibre in Commonwealth English, is a flexible, transparent fiber made by drawing glass or plastic to a diameter slightly thicker than that of a human hair.
-
product
Optical Fiber Thermal Jacket Remover - TFS-10
Shanghai Fibretool Technology Co.,Ltd.
The TFS10 thermal Jacket Remover is rugged and durable, yet small in size and light weight. Designed to strip the jacket of single fiber and ribbon cable up to 12 fibers (fiber holders sold separately), The TFS-10 provides superior ribbon and field-ribbonized stripping performance. easy to use that anyone can do clear stripping with near zero failure.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-418-M50
The 40/42-852A-418-M50 is a PXI/PXIe 8-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Fiber End-face Interferometer
Anfkom International Co.,Limited
1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement
-
product
Single Fiber Bi-Direction EDFA
HA8000
Hangzhou Huatai Optic Tech. Co., Ltd.
HA8000 series, is a bi-directional fiber amplifier with high-quality. It can transmit and amplify downlink and uplink signal on one fiber. It offers an economical solution to network operators when utilizing the existing fiber source, upgrading networks and providing bi-directional VAD business.
-
product
Erbium Doped Fiber Amplifier
EDFA
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
product
Optical Meters
The Gamma Scientific range of light meters includes handheld and benchtop models. Configuration options include a wide range of sensors and calibrations in units including: Luminous Flux (lumens) or Radiant Flux (Watts), Illuminance (lux, foot-candle) or Irradiance (W/cm2 ), Luminous Intensity (candela) or Radiant Intensity (W/sr), Luminance (cd/m2 , foot-Lambert) or Radiance (W/m2 sr), or Pulse Energy (Joules). Cooled sensors and reference standard detectors are also available.
-
product
Optical Switches
Thorlabs' optical switches are available for fiber-optic circuit integration or construction. We offer optical switches with integrated MEMS technology, optical switch kits, and PRO8 modules. Also available are optical switches for applications requiring an optical shutter in the 1500 - 1600 nm range.
-
product
Bench-top Fiber Test Instruments
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Bench-top Fiber Test Instruments
-
product
Optical to Electrical Converters
High bandwidth, broadband optical to electrical converters available in a range of configurations. Choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
Transceiver Testing
Family of RF test systems designed for transceiver testing. Designed for radio-to-radio testing in a closed mesh network. Step attenuators allow you to dynamically fade up/down the RF signal between radios. These Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted remote commands.
-
product
Digital Fiber Sensor
FX-410
Panasonic Industrial Devices Sales Company of America
This dual display digital Fiber Sensor is unique with its manual threshold value setting. Just "Look" and "Turn" simple, easy-to-use Fiber amplifier. The incident light intensity and threshold values can be checked at the same time with operation needed. In addition, no complex mode settings are needed when the values are adjusted.
-
product
Transceivers
Amphenol Fiber Systems International
*300Gb/s Optical Module*225 Electrical Connector*Customizable Duplex to 24 Channel MT Optical Cables*Solves Faceplate Density and I/O Challenges*Faceplate adapters





























