Headers
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
TB-2676, Ribbon, 100 V, PXI Module Multiplexer Terminal Block
779535-01
Ribbon, 100 V, PXI Module Multiplexer Terminal Block - The TB-2676 features ribbon cable headers that help you access all channels of the PXI-2576 Multiplexer Switch Module. You can use the TB-2676 to configure the 16 banks of 4x1 2-wire multiplexers included with the PXI-2576.
-
product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
product
VME 16-channel Differential to Single-Ended Signal Converter
V1250
The V1250 is a 16 channel differential to single ended signal converter in a 1-unit wide VME 6U form factor. It provides differential inputs (34-pin 2.54 mm header, Zdiff = 100 Ω) and single ended outputs (coaxial LEMO, Rout = 50 Ω).
-
product
Board
Arduino Micro
The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
-
product
Miniature 8-channel photon counter
id150 SERIES
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
product
DIP Header with Coined Contacts
Series 600
DIP Headers with Coined Contacts. Aries offers a full line of DIP headers, available with either coined or screw machine contacts. Consult Data Sheet No. 12035 for screw machine contacts. Snap-on, protective covers are available for all sizes shown below and accommodate .125 [3.18] to .750 [9.05] component heights. Consult Data Sheet No. 12033 for protective covers.
-
product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
CB-50 I/O Connector Block with DIN Rail Mounting without cable
776164-90
50-Pin Male IDA to 50-Pin Female Screw Terminal, DIN Rail, Terminal Block - The CB-50 provides 50 screw terminals for connection to I/O signals from your 50-pin NI data acquisition devices. The CB-50 includes one 50-pin header for direct connection to 50-pin cables. It features a protective plastic base and hardware for mounting on a DIN Rail.
-
product
Emulates Winbond W78ERD2
FE-WRD2
* Emulates Winbond W78ERD2 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
product
Arduino Shield Header Kit
INT-19002
Complete header set for Arduino Uno shields. Contains: 1 1x6, 2 1x8, 1 1x10, and 1 2x3 header. These headers have square pins and fit into standard 0.1" breadboards. Gold plated and RoHS compliant.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
VTAC, Insert Bundle, Receiver/ITA, SIM, Vertical Header and Pass-Thru
610151108
Each kit contains (1) VTAC vertical header insert and (1) VTAC pass-thru insert. VTAC vertical header inserts get press fit into a PCB and by extension of the VTAC pass-thru insert, a VPC receiver connector can be mounted to the PCB. This is especially useful when mounting an i2 MX receiver or 90 Series SIM module to a PCB.
-
product
Tool, Press Kit, i2 PCB Headers
910121199
Tool, Press Kit, i2 PCB HeadersAids in pressing fit pins into the header.
-
product
Header Covers
Series 650
Header Covers. Aries offers a complete line of DIP headers and covers useful for mounting components such as resistors, diodes, etc. Consult Data Sheet 12032 for mating DIP header information. Four cover heights provide mounting of 1/8? [3.18] high to 3/4? [19.05] high components.
-
product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ i7/i5/i3 Processors
AmITX-CF-I
The AmITX-CF-I is a Mini-ITX motherboard supporting the 8th/9th Gen Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor in the LGA1151 package, and the Intel Q370/H310 chipset. The AmITX-CF-I is specifically designed for customers who need high-level processing and graphics performance with a long product life solution. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz non-ECC memory up to 32 GB in two SODIMM slots. The AmITX-CF-I features DVI, DP and HDMI ports, LVDS header, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and audio with Line-out, Line-in and Mic-in connectors. Expansion is provided by one PCIe x16, one M.2, and one mini-PCIe slot. The onboard pin header provides GPIO, USB and RS-232 support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.
-
product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
product
Industrial Data Acquisition Module for embedded systems with PCIe/104 OneBank expansion
PX1-I440-ADC
The PX1-I440-ADC is an industrial data acquisition module for embedded systems with PCIe/104 OneBank expansion. This module features eight differential ADC (analog-to-digital converter) inputs based on the Analog Devices LTC2335-16 ADC. Analog to digital inputs terminate to a single 20-pin box header connector.
-
product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix Topology Without Column Protection Resistors
782385-07
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Connectors, Header - Male
INT-10040
1x40 pin breakaway header. These headers have square pins and fit intostandard 0.1" breadboards. Scoring makes for convenient breaking into smaller headersfor all of your projects. Gold plated and RoHS compliant.
-
product
USB Graphics Adapter, Internal Mount, DB-15 connector
DB-UVGA16
- Mounts in DB9 cutout on chassis or in PCI slot- Uses internal USB pin header- Display resolutions up to: 1600 x 1200 (4:3), 1680 x 1050 (16:10)- Supports multiple display modes: Primary, Extended, Mirr
-
product
MAX31855 T-Type Thermocouple Sensor Breakout
SEN-30001-T
Breakout board for the MAX31855T digital thermocouple interface IC. Measured temperature range is -270C-400C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
product
Interface for Two Dual-Redundant 1760 Channels
EXC-1553PCMCIA/Px-1760
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers. Each channel of the EXC-1553PCMCIA/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.The EXC-1553PCMCIA/Px-1760 card is supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
PCI Card
EXC-8000PCIe104/xx
The EXC-8000PCIe104/xx card for PCI/104-Express systems supports up to four dual redundant 1760 channels using the M8K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A,B). In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
product
1553 to Ethernet Converter
eNet-1553
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
product
SHB12X-H3X24, Male InfiniBand to Differential Flying Leads, Shielded LVDS Cable, 1.5 m
196236-1R5
72-Pin, Female Flying Leads to 48-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable - The SHB12X-H3X24 LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS digital instruments or some NI 658x LVDS Adapter Modules for FlexRIO directly to individual header pins. This cable is intended for use with a custom breakout fixture. The flying-lead cable has three signals per grouping for positive, negative, and ground pin connections designed to plug directly into any 0.1 in. header connector. It is a shielded, 100 ohm cable.
-
product
Arduino CAN Shield
IFB-10003-INP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Universal LightProbe Sensor Six-Pack
S6P
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
product
DIP Program Header
Series 675
DIP Program Headers. Aries DIP programmable headers offer unusual versatility for programming within the header itself. They can be individually programmed using cutters or Aries programming tool, Part No. T-675, available separately, to remove the interconnecting sections. Consult Data Sheet No. 22002 for Aries programming tool.
