-
product
cDAQ-9188, 8‑Slot, Ethernet CompactDAQ Chassis
781424-01
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
Fiber Acceptance Test Kit
23005
The unique design of the splice accommodates either 125um or 140um fiber and any size buffer up to 900um. The precision made splice holder firmly holds the pigtail in position without causing stress on the fiber. The low viscosity index matching liquid has an indefinite shelf life and allows for an easy glide of the bare fiber into the splice. Within seconds, a fiber acceptance reading can be made with an OTDR or test set. Low loss with minimum back reflection can easily be achieved for more accurate signatures. Other applications for this kit: splice training aids, bare fiber adapters, and temporary splicing.
-
product
Incident-based Abnormal Software Behavior Analysis Services
If you have a software problem that no one can analyze, need training to get your developers, support and escalation engineers improve their troubleshooting, debugging, memory dump and software trace analysis skills or just need the expert opinion on an existing analysis report please don't hesitate to contact us.
-
product
High-Power Tunable Filter
CB503
The need for tunable filter technology originates from the fact that high power communication systems and IED Jammer transmitters severely limit the use of tactical radio communication systems on the battlefield.This clash within the radio’s spectrum during tactical missions is often de-conflicted using fixed high Q, high power RF bandpass and bandstop filters installed prior to mission. This can limit operational effectiveness due to the potentially large number of fixed filters required within the allocated radio communication channels, which need be transported, stored in the field, and fitted by trained personnel. Many of these fixed filters centred within the octave wide tuning range could be replaced by a single high-Q tunable filter.
-
product
Discovery Hybrid Rheometers
TA Instruments invites you to experience the latest innovations in rotational shear rheometers, the Discovery Hybrid Rheometer HR 10, HR 20, and HR 30. The Discovery Hybrid Rheometers are designed for scientists who need to obtain better rheological data, under the widest range of measurement conditions, collected by more users, with less training.
-
product
Laser Systems
Laser systems (laser range finders, laser designators, laser receivers, laser trackers, laser pointers) are one of crucial technologies for defense/security sector. Laser systems have also found mass applications outside defense sector. Testing laser systems is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of night vision devices.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
PC-Based Reconfigurable Inner Ship Modeling
PRISM
Textron Systems' PRISM is used to model the user’s platform under training, providing the student the ability to “see” the environment surrounding the equipment. With PRISM, users can script malfunctions, set initial conditions, supply evaluation results, and allow the equipment layout to be tailored to meet training objectives, which more closely matches a real-platform configuration. PRISM can be seamlessly combined with FORTRIS™, which provides the comprehensive physical and electromagnetic environment outside the platform, giving the user a complete end-to-end training experience.
-
product
TDL Network Simulation
Curtiss-Wright Defense Solutions
The need for realistic and effective military training simulations is fundamental to prepare warfighters for the challenges they may face on the field. The TCG portfolio of advanced tactical data link solutions enables the creation of configurable high-fidelity simulations, both real-time or scripted, of the industry’s most prominent data link protocols and standards.
-
product
High-Speed Data Acquisition System
TMX
Astro-Med Recorders Maintain their Position as the Easiest to Use Data Acquisition Systems on the Market. Stop fumbling with those awkward buttons or knobs and complicated configurations! The TMX features an exclusive full-color 17" advanced touch screen technology, as well as pre-defined set up options, eliminating the need for training. With the TMX, you will be an expert in no time!
-
product
NI LabVIEW Development Services
Software development using National Instruments LabVIEW is a core skill of the Simplicity AI which is an NI Alliance Partner and has a technical team with over 60 years of experience in the product. Engineers are accredited with Certified LabVIEW Developer or Certified LabVIEW Architect qualifications, and several are certified by National Instruments to teach LabVIEW training courses.
-
product
Usability Testing
Underwriters Laboratories Inc.
Ascertaining the safety of medical devices obviously includes the human factor – the people who are using the device must be able to do so safely and effectively. UL''''s usability testing services are aimed at achieving compliance with regulatory requirements, reducing medical device use error, helping manufacturers create user-friendly devices, and reducing training costs.
-
product
Fiber Optic Network Simulators
SIM-2FON-25
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
product
Launch Box & Pulse Suppressor
OTDR Sidekick
Intended to eliminate the "dead zone" at the beginning of a fiber cable when using an OTDR, The Sidekick from M2 Optics is a compact, durable solution for both field and laboratory use. Commonly referred to as a launch box, pulse suppressor, or launch cable, this durable test box is also used as a fiber optic delay line and for a variety of other short-distance testing and training applications.
-
product
Trainings, Seminars, Workshops
To make your staff able to face daily tasks and handle with high productivity is in the center of our trainings. Especially when a new test sytems starts to run it is extremely important that the personnel can operate appropriately from the beginning.Our workshops are designed as classroom trainings so everybody can concentrate completely on the workshop contents without being bothered by day-to-day business or other troubles.An alternative is the training in-house so we can look after individual and concrete problems directly on-site at the running test system.No matter if we teach in our rooms or in-house we emphasize to teach concrete practical content. The participants will spend at least 50% of their time with pracitcal questions or problems. Small groups ensure the individual care of each. We offer trainings in english or german language.
-
product
Training Systems
TESCO’s Training Systems are built to your specifications to simulate various field conditions and aid in the training of field personnel in a full range of conditions and faults.
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-01
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
product
Testing Equipment for UN38.3 & UL
We provide complete lab equipment solutions for UN38.3 testing and you are welcomed to visit our lab located in Richmond, CA -- please contact us for an appointment. On-site training available with extra cost.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
WAN Simulator / Emulator
LANforge ICE
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
product
SOP Managemen and Quality Management
arivis BM-Windream
BM-windream is the 21 CFR Part 11 compliant data and document management system for the pharmaceutical industry. It is based on the market leading windream document management system from windream GmbH, Bochum. In addition to our industry-specific modules, we have access to a series of tried and tested windream add-on modules from our partner network, e.g. for e-mail archiving, linking to ERP systems, CRM systems, knowledge management or scanning solutions. BM-windream provides a basis for your data and document management that can be validated at relatively low cost (configurable standard software complying with GAMP5) and is easy to use. Users access your documents using a virtual network drive in Windows Explorer, which means that little training is required. BM-windream provides a standardised user interface over the entire life cycle of a file, from creation to deletion. At all phases in this life cycle, a change history (audit trail) is recorded. BM-windream is suitable for handling all kinds of non-managed documents. BM-Flow integrates directly with BM-windream and provides the document management functions required for SOP management,manufacturing instructions etc. All general employees can then still access the documents using the familiar Windows Explorer, while those responsible for creating documents can also use the workflow interface in BM-Flow.
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
XCITE 1200T Torsional Series
The Xcite 1200T Continuous Torsional Exciters provide high inertial torque in the frequency ranges required to excite steam turbine rotors, deisel engine crankshafts, and ship power drive trains. The speed range of up to 3600 RPM for the 1200T-9 and 7500 RPM for the 1200T-10 system is ideal for testing a broad range of rotating power generation equipment.
-
product
Syringe Pump
65x
The 65x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter to 25 mL/min. Exceptional low-flow stability at up to 20,000 psi (1,390 bar) makes this the ideal pump for high pressure applications from deep well core analysis and polymer extrusions. The 65x pumps to the lowest flow rates with zero pulsation available on the market!The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 65x pump module has a single-ratio drive train with autolubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases. Continuous pumping is available in either single or dual pumping system controlled via air valves, offering zero pulsation for unlimited delivery. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
product
Common Electromechanical Universal Testing Machine
WDW-D series
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing machines (UTM) is designed according to ASTM, ISO, DIN, EN standards etc.. It is computer-controlled and precision. Our electromechanical universal testing machine (UTM) is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycle test. The electromechanical universal testing machine features as high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, our electromechanical universal testing system is widely used in many fields such as industry factories, research and development, test institutes and training centers etc. WDW common series electromechanical universal testing machines (UTM) adopt rigid load frames, accurate load weighting system, advanced PCIE measuring & control system and intuitive modular application software. Configured with wide range of accessories for applications, the materials universal testing machines (UTM) can provide the best testing solutions for your individual application needs. With 20 years’ experience of materials testing industry and based on abundant application knowledge, we are completely capable of configuring the best solutions and more accurately testing systems for the manufacturers involved in load frame, core measuring and control elements, software package, grip/fixture that based on their specified test application and other requirements.
-
product
Ocean Signal RescueME PLB1 (Personal Locator Beacon)
RescueME PLB1
The RescueME PLB1 is the world's smallest 406mhz & GPS enabled PLBOperation of the rescueME PLB could not be simpler. To activate the PLB: Pull the retractable antenna out by its end tab, flip open the spring loaded cover over the activation button, hold the button for 1 second until the lights blink. Visual instructions are clearly printed on the case. When activated, the rescueME PLB1 will transmit accurate position data from its 66 channel GPS for a minimum of 24 hours while the integrated strobe light ensures maximum visibility.Ocean Signal has ensured that rescueME, like all of its other safety products, exceeds statutory requirements. RescueME PLB provides an incredible 7 year battery life, and is covered by a 7 year warranty. Even after more than 24 hours of continuous operation, and when the battery power is insufficient to transmit the satellite signal, the PLB1's homing beacon and strobe light will continue to operate. This high intensity strobe light features a molded lens to enhance the visibility of its efficient LED and it gives a powerful 1 candela light emission.Self-test of the PLB can be carried out with a simple button press with the start of test and results clearly indicated by a green flashing light. The antenna is easily extended like a normal tape measure and can be retracted using the winding mechanism on the top of the unit. This unique feature greatly facilitates user training and familiarization as it is not a one time deployable antenna similar to existing PLBs.rescueME comes with a snap-in mounting bracket and universal rubber mounting strap which can be fitted permanently or with each use. It is also supplied with a detachable flotation lanyard to accommodate all scenarios out of the box.
-
product
Jamming Grapnel
The Jamming Grapnel can be used as part of a longer grapnel train for clearing the route prior to laying a cable or recovering a subsea cable.
-
product
Camera Based Beam Propagation Analyzer: M2
BeamSquared
The BeamSquared® system is a compact and fully automated tool for measuring the propagation characteristics of CW and pulsed laser systems from the UV to NIR to Telecom wavelengths. Users can also measure wavelengths above 1.8 microns, including CO2 and terahertz in manual mode (a bench set-up; without the automated optical train) with a Pyrocam IV or IIIHR. Our longer optical train and patented Ultracal™ Calibration makes BeamSquared the most accurate product on the market and is ISO 11146 compliant. Its operational robustness and reliability ensures continuous use applications in industry, science, research and development.
-
product
Feedback Modules
ECoSDetector
Electronic Solutions ULM GmbH & Co. KG
Our ECoSDetector feedback modules should be used to automate train operations. Beside the usual track occupancy detection, the train specific identification number can be read. It also enables the implementation of an external track control board.
