Isolation
-
product
E & W-Band PIN Diode Waveguide Switches
Fairview Microwave’s single-pole single-throw (SPST) and double-pole double-throw (DPDT) PIN diode waveguide switches feature fully integrated WR-10 and WR-12 waveguide ports and cover popular E-band (60 to 90 GHz) and W-band (75 to 110 GHz) frequencies. Switch circuits integrate low loss Fin-line assemblies with high performance GaAs beam-lead diodes that results in 4 dB insertion loss, greater than 25 dB of Isolation and fast switching speed < 300 nsec.
-
product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
product
PXI Expandable 16x16 RF Matrix 75Ohm Type 43
45-720A-711
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
SIGNAL & POWER ISOLATOR
EE301-ISOL
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
product
10RJ50-DB9M Serial Cable, 10Pos Modular Plug to DB-9, 2 m (non isolated)
182845-02
S8 Serial Cable, 10Pos Modular Plug to DB-9, 2 m (non isolated)
-
product
10RJ50-DB9M Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)
182845-01
S8 Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)






