-
Product
Transmission Performance/Endurance Test System
-
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
-
Product
Tire Durometer
Model 2100
-
Tire hardness can be a critical factor in setting up a race car. A tire that's too hard may sacrifice traction, while a tire that's too soft may give great traction but wear too quickly, and an unmatched set of tires may result in an ill handling car. To properly set up a car, a measure of tire hardness is necessary, and the easiest and most cost-effective way to obtain such a measure is to use a durometer.
-
Product
TPMS Service
-
To warn you that at least one or more tires are significantly under-inflated, possibly creating unsafe driving conditions.
-
Product
Drive-Train/Power-Train Performance/Endurance Test System
-
This system is suitable for engine drive test or transaxle test of HEV/EV in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling a real tires or an engine. The tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
Aircraft and Truck Scale Calibrator
-
Morehouse Instrument Company Inc.
Aircraft and truck scale calibration often requires special adapters to simulate a tire. Scales come in a variety of sizes and have specific tolerances. Many other calibration laboratories do not use the right adapters or consider the impact of the uncertainty of the reference standard used for calibration.
-
Product
Pressure Mapping
TIRESCAN
-
Complete pressure imaging system for conducting tire tread analysis.
-
Product
AWD Dynamometers
-
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under "optimum" operational conditions; whereby torque is distributed to the vehicle's tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency.
-
Product
Durometer for RC Car Tires
52-79980
-
Longacre Racing Products, Inc.
RC car tires are much softer than full size car tires. This special durometer is calibrated to read RC tires correctly. Easy to use, quick and accurate.
-
Product
DIN Abrasion Tester
TF215
-
TESTEX Testing Equipment Systems Ltd.
DIN Abrasion Tester, to determine abrasion of flexible materials, such as rubber, tires, transmission belts, soles, leather etc. The abrasion tester is provided with a wide testing area to meet the most requests. Additional balance is required.
-
Product
Power Circulation Type Flat Road Tire Comprehensive Performance Tester
-
This system has a performance performance system that simulates the force applied from the vehicle side to the tire and the influence exercised from the road side by a high speed transfer unit and a high response torque generator with a power circulation system.
-
Product
Coefficient Of Friction Testers
-
Saicheng coefficient of friction (COF) tester is specialized in measuring the static and kinetic coefficients of friction of plastic film and sheet, rubber, paper, cardboard, woven bag, fabric style, metal material composite belt for communication cable and optical cable, conveyor belt, wood, coating, brake pad, wiper, shoe material, tire and other materials when sliding.
-
Product
Tire Pyrometers
52-50640
-
Longacre Racing Products, Inc.
Accurate, super-fast response electronics.Can hold highest temp reached. Compares one temp to another with the push of a button. Low battery indicator and auto shut-off. 2000 Range (tire probe max 500). F or C switchable. Standard coil cord tire probe and carrying case included.
-
Product
Tire Pressure Monitoring Systems
TPMS
-
With the widespread use of tire pressure monitoring systems (English: Tire Pressure Monitoring System - TPMS) come to new requirements on dealers, garages and tire shops. Since November 2014 every newly registered vehicle must have on board a tire pressure monitoring system as standard. With its carefully designed parts solutions and efficient service devices of VDO They are well equipped for the service!
-
Product
TIRE TREAD DEPTH GAUGE ACCESSORY
MDMAXTPMSTTD
-
*Add-on accessory that allows technician to measure tire tread depth with high accuracy when checking TPMS sensors*In one simple gesture, it can detect worn tires, tire damage and indicate poor alignment with tread depth trigger activation button*Provides a quick vehicle safety check, quickly captures 3 tire measurements (inner, center, outer)
-
Product
AWD Dynamometers
MD-AWD-500-AC/EC-100/250
-
The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
Product
Abrasion Testers
-
Abrasion tester is used to determines the resistance of elastomers by the frictional loss of the rubber in products, such as tires, conveyor belts, hoses, footwear, floor covering etc.
-
Product
550 HP Water Brake Chassis Dynamometer
CM-51S
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
Product
Capacitance Sensor Systems
-
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
Product
Speedometer Calibrator
-
Hypertech’s Speedometer Calibrator can correct the speedometer and odometer for tires up to 54 inches (depending on the application), and/or non-stock rear gear ratios. This new device is engineered for consumers that want the speedometer recalibration functions of the Speedometer Calibrator without the additional expense of the other tuning features. The Speedometer Calibrator comes with a USB cable and a CD containing software to enable quick updates and upgrades over the internet. For an additional charge, the Speedometer Calibrator can be upgraded to a Speedometer Calibrator via the internet to include all the Speedometer Calibrator features available for that vehicle.
-
Product
Pitot Static Tester
ADSE 746
-
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
Product
1100 HP Water Brake Chassis Dynamometer
CM-51
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
Product
Textile Tester
USTER TESTER 6-C800
-
The USTER TESTER 6-C800 is ready for the most demanding technical textiles applications. The amazing diversity of technical textiles applications is matched by the wide variety of quality characteristics needed in the raw material used so filament yarn producers know they must work to the most stringent specifications and standards. Quality failings, especially in the critical parameter of yarn evenness, can be expensive, but the USTER TESTER 6-C800 provides fast, accurate testing to the tightest tolerances, protecting filament producers against customer complaints and claims. Raw materials for technical textiles cover a wide range of end-uses and performance requirements. Viscose fibers, for instance, are found in lightweight blouses as well as in wire cording and high-speed car tires. Polyester, common in low-price clothing, is also transformed in special high-tech versions, for sophisticated sportswear and outdoor clothing. Countless other examples of technical applications for filament yarns span sectors such as medical, industrial, transport, engineering and protective clothing. Despite this variety of products, there is one fundamental requirement which is common to all: the absolute need for yarn evenness, measured to close tolerances, to ensure that the functional and aesthetic properties of the finished article achieve the high quality standards that customers demand.
-
-
Product
Blow Point Tester
EKT-2001BPT
-
The EKT-2001BPT Blow-Point Analyzer is a testing instrument that measures the best curing time of rubber for tire and rubber vibration isolation industry and helps to improve the productivity. By using the special design of wedge mold, it measures the real-time temperature rising during the curing to determine suitable curing time in the curing press.
-
Product
Flexometer
EKT-2002GF
-
By means of applying constant load and compression frequency to the test specimen, this instrument could help the user to understand the history of Heat Built-up and dynamic fatigue poeperties of rubber compounds. For example, while tests the tire compound, it could provide the information of rolling resistance. Pt100 temperature sensor, temperature controller in PID parameters control, and air circulator are adopted to ensure the stable temperature control.
-
Product
Gas Permeability Testers
-
Gas Permeability Tester (Gas Transmission Rate Tester) is based on the differential pressure method and is professionally applicable to the determination of gas transmission rate of plastic films, composite films, high barrier materials, sheeting, metal foils, rubber, tires and permeable membrane.
-
Product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
-
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
Product
In-Line Speedometer Calibrator Module
-
Hypertech’s In-line Speedometer Calibrator Module is an in-line module to correct the speedometer and odometer for non-stock tire sizes and/or rear gear ratios. This module is perfect for vehicles with computers that don’t allow for tire size and/or rear gear ratio correction or re-calibrate for tire sizes and/or rear gear ratios outside the range of programmers.
