Power Monitors
-
Product
RF Power Monitors
-
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
Product
Power Monitors - AC / DC Monitors
-
DARE has a complete line of AC or DC operated power monitors available in numerous package styles including 50 Hz, 60 Hz, and 400 Hz models. In addition, DARE has a series of external aircraft power monitors that continuously monitor the quality of electrical power in aircraft electrical systems, ground power equipment, auxiliary power units (APU?s), and other equipment for pre-determined over / under voltage conditions, over / under frequency conditions, loss of phase, improper phase sequence or phase rotation.
-
Product
RF Power Monitors
-
Bird's RF Power Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-02
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
C Series Current Input Module
Current Input Module
The C Series Current Input Module features programmable input ranges, variable connectivity options, and built-in noise rejection. You can also choose from options with built-in anti-aliasing filters or high-channel density to reduce the number of modules needed. The C Series Current Input Module supports safety features, certifications, input ranges, overvoltage ranges, and connectivity for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs). The C Series Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Monitor Unit For PAV Series 4-Quadrant Power Amplifier Monitor
-
The 4-Quadrant Power amplifier monitor unit is an optional unit of the PAV series of 4-quadrant amplifiers, which can be assembled into the cabinet.
-
Product
Power Monitor
ACScout-NETBB
-
The ACScout-NETBB adds a battery backup to everything ACScout NET already does. Now your monitored power data is logged and backed up using the battery. The ACScout is still a highly reliable, easy-to-use AC power monitor that plugs into an electrical outlet. It records surges, outages and variations in voltage and frequency as well as ambient temperature and can now backup all data logged with help of a new battery.
-
Product
Power Meter (LSPM)
Immunity
-
The LSPM series of RF Power Meters from LUMILOOP provides fast, accurate, and versatile power measurement across a wide frequency range. Designed for high-resolution time-domain analysis, pulse characterisation, and seamless integration with EMC test systems, these meters are ideal for modern labs requiring reliable RF power monitoring across multiple channels and applications.
-
Product
TAP Detectors And Power Monitors
-
The “Premium” jumpers are VZ TPR Certified Cables that provide the highest level of reliability. We also offer the high performance “Standard” jumpers that are Telcordia GR 326 tested and certified. Both the Premium and Standard cables are made in our state of the art manufacturing facility recognized by leading global service providers as one of the best in the industry. We attribute our success to the highly dedicated and skilled production team which starts by selecting only the highest quality fiber and connector components.
-
Product
Multi-Function Transient Fault Recorder
TR-3000
-
The TR-3000 is the only tool you need to capture and diagnose power system anomalies. With multiple recording modes and continuous transient oscillography, you will never miss an event. The TR-3000 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. The TR-3000 takes the place of several devices: • Fault and Disturbance Recorder • Transient Fault Location • Phasor Measurement Unit • Power Quality Monitor • Sequence of Events Recorder.
-
Product
Power Monitor
ACScout-NET
-
The ACScout-NET adds to what ACScout does best. Now monitor your power from anywhere in the world with new networking capabilities. The ACScout is still a highly reliable, easy-to-use AC power monitor that plugs into an electrical outlet. It records surges, outages and variations in voltage and frequency as well as ambient temperature.
-
Product
Variable Optical Attenuator
-
Shenzhen Golight Technology Co.,Ltd
Variable optical attenuator uses high-precision attenuation control components, and combines a selfdeveloped embedded data processing platform and precise calibration process, can be provided with maximum 60dB optical power attenuation and optical power monitoring function. Real-time display of input and output optical power.
-
Product
SFP Based Fiber Optic Test Solution
Eye-BERT Micro
-
The Eye-BERT Micro is a low cost, easy to use, all-in-one SFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, and optical power and temperature monitoring (per SFP capability). Additionally, with a click of a button, the Eye-BERT Micro will automatically test an SFP module based on the information it reads from the module and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
PCI Smart Bus Extenders
PCIEXT-64U - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
Power Monitors
Power Monitor
NAI''s Power Monitors are used to monitor voltage, frequency, phase characteristics, or phase rotation of single- and three-phase power lines. Specifically designed for rugged defense and industrial applications, these Power Monitors meet the most stringent performance and environmental requirements.
-
Product
Monitor / Annunciator
RTP-1
-
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
Product
Live PD Emulation
-
Flexibly Mimic Class 0 to 4 Powered Device Per PSA/PSL-3000 Test Port. Configure up to 192 Simultaneous IEEE 802.3 PD’s. User-Defined Class 0 - 4 Powered Device Modeling with or without Cable Loss. Emulate 802.3at PoE-LLDP Negotiations and Power Adjustments. Monitor Multi-Port Live Emulation Status. Available to PSA-3000 and PSL-3000 Platforms as optional license feature.
-
Product
Dual Wide Range Power Monitor
LTC2992
-
The LTC®2992 is a rail-to-rail system monitor that measures current, voltage, and power of two supplies. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The voltage measurement range of 0V to 100V is independent of the input supply. Two ADCs simultaneously measure each supply’s current. A third ADC monitors the input voltages and four auxiliary external voltages. Each supply’s current and power is added for total system consumption. Minimum and maximum values are stored and an overrange alert with programmable thresholds minimizes the need for software polling. Data is reported via a standard I2C interface. Shutdown mode reduces current consumption to 25μA typically.
-
Product
Intelligent Liquid Level Transmitter
HR8000/K/RK
-
HighReach Measuring & Controlling System Co.,Ltd
HR8000 intelligent liquid level transmitter is an input type liquid level measuring instrument, which realizes full-scale digital linear correction, digital temperature error compensation in full temperature zone, and stores compensation parameters in non-volatile memory, adopting multiple security protection mechanisms. Of the product being unusable due to the loss of the calibration parameters is avoided; the circuit module has the power supply monitoring, the watchdog monitoring function, and the input structure is all stainless steel sealed, which greatly improves the reliability of the product.
-
Product
Power Monitor
ACScout-V3
-
The ACScout-V3 is a highly reliable, easy-to-use AC power monitor that plugs into an electrical outlet. It records surges, outages and variations in voltage and frequency as well as ambient temperature.
-
Product
Wave Quality Analyzer
Nexus 1500
-
From the Industrial Giants, Fortune 100 companies to municipal utilities, an energy management and power monitoring program is critical to their success. The Nexus® 1500, the most advanced monitoring product, provides the global picture of power quality and usage from any metered point within a distribution network, enabling users to make power-related decisions quickly and effectively.
-
Product
Directional Couplers & Bridges
-
A complete line of coaxial single and dual port directional couplers, and bridges for isolating, separating, and combining RF and microwave signals in such applications as power monitoring, source leveling, swept transmission and reflection measurements.
-
Product
Optical Protection System ( Single Fiber Two-Way )
OPS-1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-1000 Optics Protection System product series, mainly applies to optical communication field of single fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-1000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path’s optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
-
Product
High Power AOD Driver
-
The Acousto-Optic Deflector (AOD) RF Driver is a three channel, three phase high power driver amplifier intended to drive devices such as the Harris H-902. The driver accepts a single low level RF input and produces three high power phase shifted outputs. The driver features adjustable gain, power monitoring, and programmable automatic protection features. The exceptional linearity and headroom allow the use of multi-tone and complex waveforms with minimal distortion.
-
Product
Generator Logger
-
Reach Technologies' Generator Monitor is a high performance, DSP enabled, power generation monitor, quality analyzer and event data logger. The Generator Monitor is ideal for monitoring 3-phase power generation installations in support of Smart Grid compliance. Our goal is to help our customers retrofit existing and OEM new installations to improve quality, and maintain stability through the fast detection, recording and notification of power faults.
-
Product
Digital Ethernet Power Meters
FU2200A
-
Beijing GFUVE Electronics Co.,Ltd.
Digital Ethernet power meter with data logger is a three-phase multifunction power and energy meter manufactured by GFUVE. It provides excellent value for monitoring power and energy management systems. It may be used as data gathering devices for intelligent power distribution or plant automation systems. All monitored data is available via a standard digital RS485 communication port, which is based on the Modbus RTU protocol.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40PS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～500A*Current measurements of feeder
-
Product
Power Monitoring Software
-
A digital tool that continuously tracks, analyzes, and manages a facility's electrical system in real-time.
-
Product
Tool and Production Monitoring Systems
Techna-Check
-
The TECHNA-CHECK® Tool Monitoring Systems have been developed to monitor for broken, worn and missing tools through spindle power monitoring or vibration analysis. Various models are available depending on the specific application requirements
