-
product
PXI Vector Component Analyzer, 100 kHz to 44 GHz
M9817AS
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
product
SF30/C High Speed Laser Rangefinder – 100 M
28058
The SF30/C High Speed Laser Rangefinders can output an amazing 18317 readings per second. Lightweight and compact, this 0–100 meter rangefinder is designed to detect terrain and obstacles or create maps from moving vehicles and UAVs. It uses a time-of-flight system to make accurate distance measurements that are not affected by surface texture, speed, wind, changes in barometric pressure, noise, ambient light, terrain, or air temperature.
-
product
Data / Ethernet
Multiplex and transport MULTIPLE GigE, 10 Gigabit ethernet streams over 110km on a single fiber, our add-on ethernet transport to any fiber transport solution we offer, such as video or digital video.
-
product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
DC Power Supply, 100 V, 0.4 A, 40 W
E36106B
The Keysight E36106B is an accurate, 100 V, 0.4 A, 40 W compact power supply for your bench or system.
-
product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
product
GN Range Broadband Power Amplifiers 100 KHZ - 200 MHZ
GN Series
Class A solid stateBroadband (instantaneous single band): 100 kHz 200 MHzTypical output power : 500 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 450 W and H < -20 dBc up to 100 MHz andP1dB > 180 W and H < -20 dBc from 100 MHz to 200Air cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
product
Advanced Ethernet Tester
LinkRunner® 10G
Quickly test, verify, and troubleshoot 1Gig, Multi-Gig and 10Gig Ethernet (copper, fiber) including line-rate performance testing and packet captureLayer 1-7 AutoTest enables any technician to find network problemsMonitor networks for intermittent issues, every minute for up to 24 hours AllyCare-enables in-depth network discovery features and web remote controlLANBERT™ Media Qualification app tests the capability of premise cabling and media components for carrying Multi-Gig and 10Gig EthernetTwo LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites
-
product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB
40-727A-101
The 40-727A-101 (PXI) and 42-727A-101 (PXIe) are 16x4 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
19" Breakout Panel for Ethernet, USB & DisplayPort
Cabinet CP-101 & CP-102
The CP-101 & CP102 are breakout panels which are used to provide a clear connection interface for 19” racks. They are equipped with the most common interfaces found on industrial computers. Both variants feature the same connectors, but distinguish in cable length (1m for CP-101 and 2m for CP-102).
-
product
Active Differential Probe, 100 kHz to 7 GHz
U1818A
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Active Differential Probe, 100 kHz to 12 GHz
U1818B
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Strain Gauge and RTD via Ethernet
2612
Simultaneous measurement of four strain gauges or RTDs6 or 4-wire measurement with 200 nV resolution at a 6 Hz rateAuto-calibration cycle measures excitation at remote strain gaugeCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
product
2 Meter Long SCSI Cable with 100 Pin Connector
U2904A
The Keysight U2904A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2904A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
product
MIL-STD-1553 Data Acquisition Module for Ethernet Networks
eDAQ-1553
Avionics Interface Technologies
One or two dual redundant MIL-STD-1553 bus interfaces - Transformer and Direct bus coupling supported - Two 10/100/1000 Mbit/s Ethernet LAN Interfaces - Streams MIL-STD-1553 bus data in standard IRIG 106 Chapter 10 format. - Compatible with 3rd party recorders and telemetry tools - All captured MIL-STD-1553 bus data provided with timestamps - Full error injection & detection capabilities - Works with AIT’s Flight Simulyzer™ GUI Analyzer/Simulator software
-
product
Dual-Port 10GBASE-T pcie Ethernet NIC
P210TP
The P210TP 2x10GBASE-T PCIe NIC builds upon the success of the widely-deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly-optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
product
NI-9149, 8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783376-01
8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9149 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9149, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
product
(100×130×19mm) C-Band DWDM Booster EDFA Module
WBA4100-FM04
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM04 series used 100 x 130 x 19mm compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
product
Power Over Ethernet For Commercial Solutions
Powerful Network Solutions for Commercial Applications
-
product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
product
100 Ampere Micro OHM Meters
Introduction: Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 100 is a direct reading tester, and uses a test current of 100A DC, resulting in true v alue and accur ate measurements. Model HL- 100 adopts digital circuit technique and is used for measuring contact resistance of switch control equipments at test current of 100A DC. The measurements are accurate as the test is highly stable.HL- 100 is a new, fully automatic micro controlled tester that measures contact resistance at 100A DC with built in printer. The advantages of HL-100
-
product
3U CompactPCI Serial 4-slot SSL w/ RTM w/ Ethernet
1CPCIS-304-L210
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 2 to 4, Ethernet full mesh
-
product
Streamline Vector Network Analyzer, 100 KHz To 32 GHz, 2-port
P5006B
Compact, faceless, vector network analyzer (VNA). Flexible two-port VNA dramatically reduces your size of test. Up to 32 GHz.
-
product
AC / DC Current Probe, 100 MHz, 30 Arms
N2783B
The N2783B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
product
Ethernet to Wi-Fi Bridge
BR-500AC
BR-500AC is the first commercially available 802.11ac wave2 2x2 MU-MIMO dual-band Ethernet to Wi-Fi bridge supporting WPA3-Enterprise Wi-Fi security. Leveraging advanced features of 802.11ac wave2 standard, BR-500AC securely, reliably, and efficiently connects any Ethernet device to your wireless network enabled by a recent Wi-Fi access point.
-
product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
product
8 Channel 100 MS/s 16-bit ADC
SIS3302
The SIS3302 is the 16-bit extension to our 100 MS/s digitizer family. It is the 2nd DDR2 memory based digitizer unit in the SIS33xx family. The board is used for the readout of high resolution detectors, accelerator controls and other applications.
-
product
100 Watt Dynamic Measurement DC Source, 20V, 5A
66332A
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66332A Dynamic Measurement dc Source provides dynamic measurement and analysis of voltage and current waveforms. It is ideal for testing digital wireless communications products/components because it not only provides the power for testing, but also performs the peak current measurements required to characterize the pulsed current demands of these products.
