UDP
-
Product
UDP Test Tool, Flood Generator, VoIP Readiness Test Tool
-
The Multiprotocol Network Tester is a freeware, open source tool which enables you to measure quality of your IP network. It can also be used to generate UDP flood or to simulate UDP DoS attack. SIP call is usually established using a SIP session with a bidirectional RTP stream. SIP and RTP protocols are based on UDP transport protocol. UDP uses a simple transmission model without implicit reliability, ordering and data integrity. Each single UDP packet is transferred independently. The quality of a SIP call depends on delays and loss of IP packets in a network. Long delays lead to large RTP jitter and bad sound quality of a SIP call.
-
Product
Multi-Channel PCM Processing and Recording System with UDP Streaming
LS-68-M
-
The Lumistar LS-68-M Modular Multi-Channel processing and recording Telemetry Processing System offers an ultra-small, low-cost, high-performance, multi-channel COTS solution for PCM data synchronization, decommutation and simulation applications. Building on the legacy of the Lumistar LS-45, LS-50, LS-55 and LS70 series of products, the LS-68-M enhances the feature sets of each of these product lines and supplies them in a format requiring no hardware drivers in an “OS-less” environment. The LS-68-M utilizes a highspeed Gigabit Ethernet interface for primary controls and data streaming.
-
Product
UDP Test Suite
-
Design engineers, quality assurance engineers and testers use the IWL UDP Test Suite to find and fix bugs in their UDP implementation. The tests help ensure that the UDP implementation is sufficiently robust so that it is not vulnerable to the wide range of attacks in today's Internet. The tests make use of the Maxwell Pro network emulation environment, so that each test sequence can intelligently impair all aspects of the UDP protocol.
-
Product
FPGA UDP Packet Interface Connnecting 3-4 Channels of MIL-STD-1553 to Ethernet in Real-Time
ENETX-1553
-
ENETX-1553™ is an innovative product that provides “remoting” of 1553 operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENETX-1553 is a small, low-power, rugged device that provides real-time Ethernet connectivity to for three or four dual redundant 1553 (A/B) buses (channels). Ideal for remoting 1553 connections for in-field applications or point-point lab usage. AltaAPI provides and highly portable BSD SDK and National Instruments LabVIEW and LabWindows. ENET products are unique in the market as they have a hardware, FPGA real-time UDP engine – no OS or IP stacks – provides maximum throughput and ultimate virus protection.
-
Product
Multi-Band Dual-Channel Receiver/Combiner, 4U Rack Mount System with Integral Tracking Receivers and Bit Syncs
LS-28-DRS Series
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SOSA Aligned 3U VPX
Model 5553
-
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- 10 GigE Interface- 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 49, VITA 46, VITA 48, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8256 3U VPX SOSA Aligned Development Chassis- Model 6003 unique QuartzXM eXpress module enables migration to other form factors- Video: Model 8256 3U VPX SOSA Aligned Development Chassis- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Avionics Interfaces & Test Instruments
ARINC 664
-
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
Product
Network Interface Card
NIC10G
-
Featuring the Intel 82599ES dual 10GbE controller, the NIC10G supports flow control, integrated IPsec security engines, optimized queues, IPv6 offloading, advanced filtering capabilities, and Tx/Rx IP, TCP and UDP checksum offloading capability. Also has integrated a PCI Express Gen 2 interface supporting up to 8 lanes.
-
Product
TamoSoft® Throughput Test
-
TamoSoft Throughput Test is a utility for testing the performance of a wireless or wired network. This utility continuously sends TCP and UDP data streams across your network and computes important metrics, such as upstream and downstream throughput values, packet loss, and round-trip time, and displays the results in both numeric and chart formats. TamoSoft Throughput Test supports both IPv4 and IPv6 connections and allows the user to evaluate network performance depending on the Quality of Service (QoS) settings.
-
Product
AFDX® / ARINC 664 Test And Simulation PCIe Module
PCIe-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Multi-Band Quad-Channel Receiver/Combiner, 4U Rack Mount System with Integral Tracking Receivers and Bit Syncs
LS-28-QRS
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
Receiver/Combiners
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Ethernet
-
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards (only 64 bit versions). The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.The receive channels allow for the storage of all packets to all MAC and IP addresses with status and Time Tag information appended to each packet. The receivers allow for filtering based on MAC address, IP address and UDP port. The transmit channels enable the user to define a Bus list which controls timing and order of packets without host intervention or immediate mode which enables the host to transmit packets at will.
-
Product
Multi-Channel, Multi-Protocol ARINC Ethernet Appliance
ENET-MA4
-
eNet-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNet-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 8 ARINC channels.
-
Product
IP Video Stream Monitoring Probe
TSM Probe
-
The Mividi TSM Probe is a compact system that runs Mividi TSM100 video streaming monitoring software and TSM Web remote management software on an Intel NUC PC. It receives data via IP interface and supports most common streaming protocols including TS over UDP, RTP, HTTP, HLS, RTMP, RTSP and MMS. The size of the device is only 4.5 x 1.9 x 4.4 inches, and it can be used for remote monitoring of IPTV and OTT video services in the proximity of customers.
-
Product
Audio Loudness Monitoring And Logging System
-
The Mividi® Audio Loudness Monitoring and Logging System (Loudness Logger) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that supports audio decoding, loudness monitoring and logging, log file management and playback. It takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous monitoring and recording over 50 channels simultaneously.
-
Product
Virtex UltraScale+ HBM FPGA Processor - SOSA Aligned 3U VPX
Model 5586
-
- Jade 5585 and 5586 FAQ- Co-processor for distributed FPGA processing tasks- High-Bandwidth Memory (HBM) delivers 20x more memory bandwidth than traditional DDR4 solutions- Board interfaces: 1 GigE, 10 GigE, 40 GigE, dual 100 GigE and PCIe- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX proessing powerhouse- Features Xilinx Virtex UltraScale+ HBM FPGAs- 10 GigE Interface and 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled- Navigation Design Suite for software and custom IP development
-
Product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
HPx-346 Analogue to Network Radar Converter
-
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
Product
I2C Adapter MS
LAN
-
*No driver necessary*Integration of communication via DLL and TCP / IP & UDP protocol possible*Open interface description enables communication without a DLL*Supports TCP / IP, UDP and DHCP
-
Product
cRIO-9805, 4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO
786993-01
-
4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO - The cRIO-9805 is a 4-port Ethernet switch that provides additional ports with 802.1AS network synchronization capability over the 1000 Base-TX network interface. This module supports TCP/IP and UDP network protocols in DHCP + link-local, DHCP, static, and link-local network IP configurations. The cRIO-9805 auto-negotiates communication rates of 10, 100, or 1000 Mbps with its four internally switched ports.
-
Product
Ultra Low Power Radios
IoT
-
IEEE 802.11b/g/n-compliant Wi-Fi Radio (2.4 GHz)Ultra-low-power hostless Wi-Fi IoT Module features QCA4010 RadioSingle Stream System (1x1), 20 MHzIntegrated RF front end and PCB trace antennaHostless IoT application development platform with large internal memoryUART AT command set for optional external MCU hostAllJoyn supportWi-Fi Protected Setup SupportIPv4 / iPv6, TCP and UDP Protocol Supported on Chip, Offloading the Host ControllerIdeal for cost effective Internet of Things (IoT) Applications
-
Product
Portable Multi-band Dual Channel Receiver/Combiner
LS-84-EC-DRS Series
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - 3U VPX
Model 5950
-
- Now available in RFSoC Gen 3 with the Model 5953- Multi-board synchronization with Quartz RFSoC video- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional VITA-66.4 optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA-46, VITA-48, VITA-66.4, VITA-57.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products- Model 4801 Carrier Design Kit for designing custom carrier for the Model 6001 QuartzXM- Model 6001 unique QuartzXM eXpress module enables migration to other form factors- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX
-
Product
Serial to Ethernet Connector
-
With Serial to Ethernet Connector you can share up to 255 serial devices over network turning your computer into a terminal server. With this serial over network solution any device connected to a COM port can be accessed and used from any spot on the globe as if it were physically connected to the local machine. The data sent by serial port device is transmitted over a TCP/IP network. This is achieved thanks to our virtual serial port technology that emulates standard COM ports behavior and Windows OS treats the virtual ports as the real ones. Although the ports are treated as physical you are not limited to the quantity of physical COM ports and can create COM port connections without occupying real serial ports. With Serial to Ethernet Connector you can: share serial port for incoming connections, connect the port to remote host, or share port using UDP connection. Starting from version 7.0 Serial to Ethernet Connector got absolutely new user interface for even easier creation and management of connections with latter conveniently visualized and more.
-
Product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
-
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
