Gages
See Also: Gauges, Pressure Gauges, Height Gauges, Pressure Gages
-
product
Optical Gaging Products
Quality Vision International Inc.
OGP® pioneered multisensor measurement with vision, touch probe and laser sensors. For over 75 years, OGP has consistently led with a succession of innovative systems and sensors to tackle the most difficult measurement challenges, especially as it pertains to the medical industry. Multisensor metrology is a preferred quality control technology for manufacturers to develop, maintain, and improve the quality of medical devices.
-
product
Automated Gage Measurement System
AGMS
Our Automated Gage Measurement System for Sand Screen (AGMS) provides accurate and repeatable optical measurements for all wire-wrapped gaps along the full screenlength. This inspection machine enables oil field sand screen manufacturers to meet the measurement requirements of API Spec 19S1 and ISO 17824:2009.
-
product
Low Profile Universal Tension or Compression Load Cell
LPU SERIES
Our LPU Series are low profile, universal tension or compression "pancake" type load cells. They are available in 14 ranges from 100 lb through 50,000 lb Hold down bolt holes are provided through the outer diameter and a threaded hole provided through the center for pushing or pulling from either end. The ALB load buttons located in our accessories section, are ideal for compression applications. The LPU Series are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Mini-Photohelic Differential Pressure Switch/Gage
MP
The Series MP Mini-Photohelic differential pressure switch/gage combines the time proven Minihelic II differential pressure gage with two SPDT switching setpoints. The Mini-Photohelic switch/gage is designed to measure and control positive, negative, or differential pressures consisting of non-combustible and non-corrosive gases.
-
product
Digital Indicating Pressure Transmitter
DSGT
Series DSGT Digital Indicating Transmitter is a versatile multi-function process gage that features an excellent 0.25% full scale accuracy.
-
product
Digital Signal Processing
Digital signal processing routines can be conducted on raw signal data acquired by GaGe high-speed digitizers either directly on the onboard FPGA of the digitizer card via our eXpert FPGA firmware features or can be optionally conducted on GPU cards receiving real-time streaming of raw signal data acquired by GaGe high-speed digitizers via the PCIe interface.
-
product
Electronics For Signal Processing
PCB Piezotronics manufactures a wide variety of electronics to power ICP®, PE (Charge Mode), MEMS, strain gage and other types of sensors. All of these products provide conditioning of sensor signals for transmission to data acquisition systems.
-
product
PCIe Octopus Express 14-Bit Digitizer
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
product
*Coordinate Measuring Machine
PRISMO ultra
PRISMO ultra uses uncompromising precision technology and was developed for measurements that require extremely high accuracy. PRISMO ultra incorporates a well-balanced combination of cutting-edge accuracy, speed, rigidity, and cost performance. This 3D coordinate measuring machine is best suited for research and development of high-precision parts and calibration inspection of reference gages.
-
product
Automatic Transmission & Engine Oil Pressure Tester
34500
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Gage calibrated from 0-600 PSI (0-4,000 kPa & 0-7.0 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a durable vinyl pouch.
-
product
Coordinate Measuring Machines
FlatScope
Perfect for the measurement of larger 2D profiles (e.g.),films, circuit boards, laser cut and stamped parts large and smallMachine design with the image processing sensor under the glass plate, eliminates time-consuming focusing as the workpiece is always in the correct distance to the opticsIn raster scanning mode the machine also quickly captures the selected measurement range completelyAll geometric features are then evaluated automatically in the imageQuick dimensional measurements in the scanned image and automatic gaging with ToleranceFit® comparisons
-
product
Solid Plastic Stationary Gage
200/300
Dwyer solid plastic stationary gages - or draft gages - are offered in inclined and vertical (well-type) styles for highly accurate laboratory or general industrial service, for measurement of low range gas and air pressures, positive, negative or differential.
-
product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
785994-01
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
product
Static Soil Tester
GEO-probe
The complex is implemented on the basis of a portable computer and the CompactRIO control and measuring system. The software for recording and displaying measured signals and control of measuring equipment is developed on LabVIEW. The second modification of the measuring system includes, developed by our company, a miniature digital measuring module of a strain gage with a built-in ADC and inclinometer and a USB interface for connecting the digital measuring module of the probe to the computer.
-
product
Strain Gauge Measuring Instruments
It is a Strain Gage Indicator and also function as a Strain Gage Transducer Indicator.As a Strain Gage Indicator, it can support 10 types of bridges and dummies. While if used as a Strain Gage Transducer Indicator, there are 24 bits A/D converts to make the measurement.
-
product
Precision Line Gage
PLG100
The PLG100 Precision Line Gage system is specially designed for desktop use in order to measure conductor line widths, conductor line spaces, arcs, circles and other patterns on the PCB. It can measure a conductor line width less than 1 mil. The PLG100 system is unbelievably light weighing only 0.73 kg and providing easy mobility
-
-
product
Full Bridge Thin Beam Force Sensors
TBS SERIES
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
product
Precipitation Sensors
Campbell Scientific offers several types of sensors to measure precipitation: tipping bucket rain gages, siphoning tipping bucket rain gages, heated rain gages, and snowfall adapters. Users often select their precipitation sensors based on the type of precipitation to be measured (rain or snow), as well as the needed orifice diameter, measurement range, and accuracy level.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
EHC-09 Ultrasonic Corrosion Thickness Gage - Monochrome
EHC-09
Danatronics most popular thickness gages are those in our EHC-09 series. With thousands of units in the field, our durable, custom molded case with raise rubber keypad is IP54 rated and has proven it can handle your toughest jobs (this is bad help fix). The EHC-09 series is available in 6 models to suit every budget and application. What’s best is our simple upgrade path where all gages are capable of quickly and easily (directly from the keypad) adding any software options. Features include a graphic display with multiple languages, vibrate on alarm, fast minimum, echo to echo to ignore coatings, 100K reading Datalogger with export to excel, B-scan and live A-scan with waveform adjust.
-
product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
product
14-Bit Digitizer For PCIe Gen-2, 4 Channels 125 MS/s Up To 8 GS Memory
Octave-14 Express / CompuScope 8349
The GaGe Octave Express 83XX CompuScope PCIe digitizer card features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11.1-bits with 10 MHz input. Onboard digitizer sample memory is expandable up to 8 GS (16 GB) and up to 8 Octave Express digitizers can be combined for up to 32 channels in a single system.
-
product
ECHO 7 Ultrasonic Precision Thickness Gage
ECHO 7
ECHO 7 represents our most advanced thickness gage ever. ECHO 7 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of contact, delay line and immersion probes from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD card memory and interface to Microsoft excel. The ECHO 7 is available in 4 models including the ECHO 7, ECHO 7DL, ECHO 7W and ECHO 7DLW.
-
product
Solid Plastic Portable Gage
100
Dwyer solid plastic portable manometers are precision instruments in inclined and vertical (well-type) styles for the measurement of static pressure, vacuum or differential pressure. To assure the accuracy required in instruments of this type, all machining of bores and wells is to the highest standards of precision backed by Dwyer's years of experience in the fabrication of acrylic instruments.
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Gage EXpert FPGA Realtime Data Streaming
eXpert Stream-to-Analysis
All Gage PCI Express CompuScopes are able to Stream waveform data through the PCI Express bus directly to PC RAM. By contrast, older Memory Mode operation required storage of data in dedicated digitizer memory prior to data transfer. Streaming provides two distinct advantages over Memory Mode. First, Streaming may overcome the acquisition time limit imposed by the volume of dedicated digitizer memory. Second, in Streaming Mode, the user does not need to await completion of waveform acquisition before accessing the resulting waveform data, which is necessary in Memory Mode.
-
product
16-Bit PCIe Gen-2 Digitizer / Oszilloscope 4 Channel 25 MS/s Up To 8 GS Memory
Octave-16 Express / CompuScope 8442
The GaGe Octave Express 84XX CompuScope PCIe digitizer card features 16-bit resolution with sampling rates up to 25 MS/s with true Effective Number of Bits (ENOB) of 12-bits with 10 MHz input. Onboard digitizer sample memory is expandable up to 8 GS (16 GB) and up to 8 Octave Express digitizers can be combined for up to 32 channels in a single system.
-
product
Hall Effect Thickness Gage
Magna-Mike 8600
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
product
Through Hole/ Donut Load Cell Compression Only
THA SERIES
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
