Conductance
See Also: Battery Conductance Testers
-
Product
Panel Mounting Conductivity Transmitter
DO9786T-R1
-
output of a conductivity electrode with temperature compensation into a 4÷20 mA signal.
-
Product
Artificial Power Network
KH3765
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
Product
Software Packages
GLUON
-
The software uses notched specimens (CT specimens) to evaluate the material elasto-plastic fracture toughness value (JIC). The test is conducted at constant loading rate under test-force control or CTOD control and the load is removed to calculate the crack length. The software plots graphs of the crack length increase (Δa) and crack growth resistance (J value) from the acquired data, calculates the JIC value, and evaluates its validity.
-
Product
Hardy Shaker
HI-903
-
This is our top of the line Hardy Shaker. It provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting vibration tests easier. Tests can be conducted on multiple vibration transducers, and then the saved data can be transferred via USB Flash Drive to be displayed in an automated and customizable report using an Excel template on your computer. In manual mode, the vibration test level and test frequency can be set from 7 Hz to 10,000 Hz. The high accuracy instrument can display the vibration level in terms of g’s peak, velocity peak (in/sec or mm/s) or displacement peak-to-peak (mils or µm). The unit can support payloads up to 800 grams (see frequency limits in the manual). A built-in display reads the output sensitivity, which can be stored in memory. Complete testing sequences and data can be stored in memory for each tested sensor, the unit logs the data on the spot or stores it for later use. For testing of heavy transducers or at high frequencies, the HI-903 automatically corrects the sensitivity calculation for the effects of transducer mass loading. A built-in self-test program checks for accuracy of all calculations. The HI-903 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
Product
Benchtop Multi-Parameter Water Quality Meters
-
Labodam benchtop multi-parameter water quality meters come with different measurement modes for quality and testing of water on different parameters such as pH, conductivity, TDS, salinity, and resistivity content from the test sample.
-
Product
CARB Testing
-
Underwriters Laboratories Inc.
The ASTM D6007 (small chamber) and ASTM E1333 (large chamber) test methods are used by the composite wood products industry to measure emissions of formaldehyde from plywood, particle board and medium-density fiberboard (MDF), commonly known as CARB testing. Testing is conducted in environmental chambers operated at defined product loading, temperature and relative humidity.
-
Product
PRO Waterproof 3-in-1 Conductivity / TDS & Temperature Tester
EC59
-
The Milwaukee EC59 PRO Conductivity (EC) & Total Dissolved Solids (TDS) Tester is designed for aquaculture, food, wine, laboratory, water treament and many other applications. It is the ideal meter to help make sure that your EC/TDS/Temp. needs are being met and are reliable results for your analysis. Keep EC/TDS/TEMP. in your target range to help your achieve best results.
-
Product
Oscilloscope Probe
-
Oscilloscope Probes can conduct signals up to 2.5 GHz, 300 V, or 500 Arms, even in extreme environments. They offer fixed attenuation of 10X or 100X or switchable attenuation between 1X and 10X. Oscilloscope Probes are offered in several types, including single-ended and differential, active and passive, voltage and current.
-
Product
Capacitive Sensors
-
Capacitive proximity switches detect conductive and non-conductive materials that can be in a solid or liquid state. They serve the purpose of monitoring product levels in containers, checking contents in filling and packaging systems as well as detecting, positioning, monitoring and counting objects, e.g. in sequence control systems, conveyor belts.
-
Product
Level Switches
-
Omega can meet your level measurement requirements by offering switches of various technologies including capacitance and conductivity, tuning fork, ultrasonic, optical, and rotating paddle switches.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
PCB Systems Vibration and Acceleration Simulation Solution
Xpedition
-
As the industry’s market share leader in PCB design software, the Mentor Graphics® Xpedition product augments mechanical analysis and physical testing by introducing virtual accelerated lifecycle testing much earlier in the design process. This is the industry’s first PCB-design-specific vibration and acceleration simulation solution targeting products where harsh environments can compromise product performance and reliability, including the military, aerospace, automotive and industrial markets. Traditional, physical HALT (highly accelerated lifecycle testing) is conducted just before volume manufacturing, and requires expert technicians, which can result in costly schedule delays. Bridging mechanical and electronic design disciplines, the Xpedition product provides vibration simulation significantly faster than any existing method. This results in increased test coverage and shortened design cycles to ensure product reliability and faster time to market. The Xpedition component modeling library is the most extensive in the industry, comprised of over 4,000 unique 3D solid models which are used to create highly defined parts for simulation. The 3D library allows users to easily match geometries to their 2D cell database. Designers can assemble the parts models on board and automatically mesh them for performance analysis, including stiffeners and mechanical parts. The system modeling tool is ultra-fast since it can model over 1,000 components per minute.
-
Product
Dopant
-
In semiconductor manufacturing, electrical performance starts with atomic-level control. Dopant technologies make that possible by introducing carefully measured doping constituents that help devices conduct, switch and perform reliably. For precise control of fluxes for Molecular Beam Epitaxy (MBE) dopant constituents, or for gases that do not require thermal cracking, Veeco’s Dopant products are ideal.
-
Product
Circulators
-
To protect a power amplifier in case of bad antenna matching the use of a circulator is recommended. This item conducts the reflected power into an external terminating resistor where it is absorbed. Therefore the power amplifier is protected well because the output stage is always matched correctly.
-
Product
Eddy Current Scanners
-
United Western Technologies Corp
a non-destructive testing (NDT) device that uses electromagnetic induction to detect surface and near-surface flaws in conductive materials.
-
Product
Type 12R1 Family of 19" Rackmount Chassis Platforms, Reduced Weight, Rugged
12R1
-
The Type 12R1 family is a 19" rackmount chassis platform that is rugged yet lighter weight than the sturdier Type 12R2 platform. The chemical conversion coating provides corrosion protection and electrical conductivity. The rear evacuation cooling system uses high CFM blowers to remove the heat generated by the board payloads.
-
Product
IsoPods: Streaming Meters For Recording Temperature, PH, Conductivity And Dissolved Oxygen
-
eDAQ isoPods™ are portable streaming data recorders. These electrically-isolated meters can be used for recording data in situations where signal noise and crosstalk would otherwise be an issue.
-
Product
Liquid Thermal Shock Baths
TSB Series
-
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
Product
VPX Extender 3U All Differential - Conduction / Convection
119EXT3024-37XXR
-
VPX Test Extender 3U x 240mm for conduction cooled boards in convection chassis.
-
Product
Transmitter
5081
-
The Model 5081 family of transmitters can be used to measure pH, ORP, conductivity (using either contacting or toroidal sensors), resistivity, oxygen (ppm and ppb level), free chlorine, total chlorine, and ozone in a variety of process liquids.
-
Product
Water Source Measurements You Can Count On
TechPro™ II (TP1, TPH1)
-
Obtain reliable and accurate measurements of your water source with the value-priced TechPro II™. Ideal for water treatment testing as well as other industrial and commercial applications, these instruments reflect Myron L®’s 55-plus years experience designing and building quality conductivity, TDS and pH measuring instrumentation.
-
Product
CT Polarity Tester
DIR CT
-
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
-
Product
CS/ONH-Analysis
G6 LEONARDO
-
The high-end thermal conductivity detector used for hydrogen and nitrogen analysis allows detection limits in a sub-ppm range (based on 1g sample mass)
-
Product
PXI 3A Power MUX BRIC, 20-Channel, 12-Pole
40-571-305
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Cryogenic Probe Station
FWPX
-
Lake Shore’s FWPX probe station is designed for researchers who require large-size wafer probing. The FWPX accommodates wafers up to 102 mm (4 in) in diameter and can be modified to accept up to 152 mm (6 in) wafers. This general-purpose probe station is designed for researchers or engineers conducting material characterization tests over large samples. It is also an effective unit for measuring organic materials.
-
Product
Weatherometer with Air Cooling System, 80 Liters, 175 Liters, 225 Liters
-
Wewon Environmental Chambers Co, Ltd.
Weatherometer test is important to bring out the defects in something and to ensure its durability. The weatherometer result will make us identify those areas which need immediate improvements. But, there are areas where basic testing is not enough and does not do the job perfectly. To meet the high quality requirement, there is a need to perform extensive weatherometer testing on some materials. A place where such kind of testing is conducted is the xenon weatherometer.
-
Product
Force Tensiometers
Sigma 703D
-
Sigma 703D is a simple and robust digital force tensiometer for accurate measurement of surface and interfacial tension (Platinum Du Noüy ring, Platinum Wilhelmy Plate), and density. Manual measurement of Critical Micelle Concentration (CMC) can also be conducted.
-
Product
Universal Cable/Harness Tester
LX-680
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The maximum test spot is 256.
-
Product
Performance Testing & Engineering Services
-
At ImpactQA, Performance Testing & Engineering services are focused at providing end-to-end testing and reporting solutions to global clients. Our performance team makes use of a holistic approach to deliver quality software applications. We manage performance testing services for a broad range of applications such as web, mobile, client-server, and cloud systems. ImpactQA with its extensive performance test & engineering lab help clients launch trustworthy applications by conducting effective load testing supported by volume testing, stress testing, etc.
-
Product
300 Mm Semiconductor Processes
-
With the Center Nanoelectronic Technologies (CNT), the Fraunhofer IPMS conducts applied research on 300 mm wafers for microchip producers, suppliers, equipment manufacturers and R&D partners. In the field of FEoL and BEoL we offer the following technology developments and services at Ultra Large Scale Integration level (ULSI):
