Line Impedance
See Also: Line Impedance Stabilization Network
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
Manual Tuners / Impedance Tuners
-
Maury manual tuners are based on precision slide screw technology that utilizes broadband slab line transmission structure and passive probes to create impedances for devices. The probes are designed to be very close to onequarter wavelength in the linear dimension at the mid-band of each range. Since each tuner has two probes, this results in improved matching characteristics for each unit. Another key feature of this series of tuners is the inclusion of a LCD position readout of the carriage position on those units operating below 18 GHz. Higher frequency tuners utilize a micrometer carriage drive. The positional repeatability and high matching range of these tuners make them ideally suited for use as a variable impedance source in applications like device characterization. Such measurements depend upon the ability of the tuner to establish impedances out near the edge of the Smith chart and to reproduce the electrical characteristics as a function of mechanical position. The tuners in this series are also easy to use due to the nearly independent electrical results of the mechanical motions. The depth of penetration of the probe into the transmission line determines the magnitude of the reflection, while the position of the probe along the line determines the phase. While there is some interaction, the effects are almost independent of each other. https://www.maurymw.com/images/mw-rf/mst982e35.jpg
-
Product
Precision Line Gage
PLG100
-
The PLG100 Precision Line Gage system is specially designed for desktop use in order to measure conductor line widths, conductor line spaces, arcs, circles and other patterns on the PCB. It can measure a conductor line width less than 1 mil. The PLG100 system is unbelievably light weighing only 0.73 kg and providing easy mobility
-
Product
15T Standard Running Line Monitor
RLM15T-3.0-S
-
The DLM 15T Running Line Monitor measures the tension on a rope passing through its three wheels. Typically used in cable laying and winch operations to measure and record line tension the robust design has become an industry standard. The monitor can be supplied as a separate item for integration with customers existing PLC’s or with a DLM digital display/HMI touch screen display.
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
Central Office Line Simulator
AI-7280
-
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Product
Line Monitor
LE-170SA
-
LE-170SA is a compact hand-held size line monitor for CAN/LIN. It has a touch screen and can be control as for smartfones. It has 1 CAN channel and 1 LIN channel and it can monitor both CAN and LIN communication thus monitoring of the network which has both CAN and LIN is available. The monitor function can diplay the communication data in real-time while saving it. The simulation function can send/receive the test data instead of the original communication partner. The ID filtering and trigger function make your development/evaluation more efficient. It also can measure 4 external signals as degital signals or analog signals while monitoring the communication data.It is light (300g) and convenient for field testing. The line monitor is useful for not only development but also maintenance.
-
Product
Impedance Analyzers
HTF-1100.
-
A laboratory furnace used specifically for the electrical characterization of materials and also for heat treatment between ambient temperature and 1100 °C.
-
Product
Single-in-Line (SIL / SIP) Reed Relays
-
The SIL / SIP reed relay is the industry standard when high reliability and consistent performance are desired in a compact package. Pickering Electronics Series 100 - 110 SIL / SIP reed relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications.
-
Product
Test Line • Equipment For Testing For Function
-
The test equipment is used for qualitative functional testing of discharge power supply units and / or ionization units from the static line and air line (discharge). The devices are usually operated with a single button and indicate via LED, whether the device under review functions properly.
-
Product
Precision Impedance Analyzer (10Hz to 130MHz)
ST2851
-
ST2851 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. It is based on Windows10 operating system, which realizes a fully computerized operation interface, making the measurement more intelligent and easier.ST2851 series impedance analyzer surpasses the 120MHz frequency bottleneck of similar foreign instruments, and solves the defect that it can only be analyzed but cannot be tested independently. At the same time, it adopts two interfaces of single test and analysis to make the test easier.
-
Product
End-to-End Flight Line Confidence Test Set
MEON™
-
MEON™ is an end-to-end flight line confidence test set for directional infrared (IR) countermeasures (DIRCM) and ultraviolet (UV) missile warning systems. It also incorporates an IR beacon and an IR detector to provide complete, end-to-end testing, alignment checks and calibrated radiometric measurement of DIRCM.
-
Product
Broadband Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-32Gbps / DC-17GHz) tunable clock/data phase shifterDelay adjustment range of 265psExhibits low jitter and limited temperature variation over industrial temperature range1GHz of bandwidth for the phase adjustment tuning portFully differential CML input interfaceFully differential CML output interface with 600mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 1WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
16 Port Analog Phone Line (FXS)
SIM-16FXS
-
This unit has 16 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
End of Line Noise Test System
-
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Product
10 Gb/s Programmable Digital Delay Line
PDDL10
-
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
Product
USB Line Camera
-
The USB Line Camera is an easy-to-use cost-effective board-level line scan camera. It consists of two circuit boards, the main circuit board and the sensor circuit board.
-
Product
Programmable Delay Line Instrument
XS-100
-
The XS-100 is designed for those who need faster switching speeds and measurements without interruptions
-
Product
Line Injector
J2120A
-
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
Product
Line Splitters
-
Precision Mastech Enterprises Co.
Allow for safe, accurate current measurements using a clamp-on ammeter without damaging or stripping the appliance's power cord.
-
Product
Dual Output AWGN Generator Line Module
458-AWGN2
-
The Model 458-AWGN2 is the ideal solution for injecting Additive White Gaussian Noise (AWGN) for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing applications.
-
Product
Inrush Current Generators for Zno Production Line
-
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
High Impedance Transformers
-
Osborne high impedance transformers are used to step-up, step-down and isolate voltages in single phase and three phase circuits. A properly designed high impedance transformer can be used an an equivalent to an isolation transformer connected in series with an inductor. The high impedance characteristic may be employed as a current limiting feature in both the primary and secondary circuity.
-
Product
Very Compact Linear Line Array Loudspeaker
LINA
-
Easily the smallest and lightest in the series, LINA and its companion control element 750‑LFC bring the inherent linearity, low distortion, and exceptional power-to-size ratio of LEO Family technology to a wider range of applications and venues.
-
Product
High Line Pressure Transducer
P365
-
The P365D transducer is designed to make low differential pressure measurements at high static line pressures. Operating from unregulated 9 to 55Vdc, the P365D is available with 4-20mA, 5Vdc or isolated 5Vdc output over full scale pressure ranges from 8 to 10,000 psid. The output shift due to static pressure will not exceed 3% of full scale, up to a line pressure of 10,000 psig.
-
Product
FC Impedance Meters
-
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
Product
Xi Series Compact Line Infrared Camera
-
The Optris Xi Compact Line is a revolutionary series of infrared cameras that usher in a new era of affordable, high-quality, and precise non-contact thermal imaging. In infrared imaging, the Optris Xi Compact Line shines with its capacity for non-contact temperature measurement. Operating within a broad infrared wavelength range, this forward-looking infrared imager captures data beyond the visible spectrum, allowing for accurate surface temperature measurements.
-
-
Product
LCR Meters & Impedance Measurement Products
-
Hewlett Packard, Agilent and Keysight have contributed innovations and product excellence in impedance analysis for over half a century. Whether your application is in R&D, production, quality assurance, or incoming inspection, we take pride in contributing to your success. We strive to deliver complete solutions to meet your needs, from impedance analyzers to a wide variety of test accessories. Achieve success with Keysight’s impedance measurement solutions.
-
Product
Impedance Analysis
S96041B
-
Make impedance analysis measurements of Surface Mount Device (SMD) components on the E5080B vector network analyzer with 16198A-010 10 GHz SMD test fixture.
