Wire
See Also: Contacts, Harness, Connectors
-
Product
32 Channel Analog Comparator Module
DP-VXI-5106
-
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Screwlocks
A068SMR-T-6B100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Gauge Type T Thermocouple Wire
W-TW-30
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 1m, HV
40-972-009-1m-FU-HV
Cable Assembly
A range of 9 Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Cable Assy 9-Pin D-Type, F/F, 0.5m
40-970-009-0.5m-FF
Cable Assembly
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Test Equipment
ST9020
-
Shenzhen Star Instrument Co., Ltd.
The ST9020 single-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.1 and 0.05. As divided by structure there are combined type, integrated type and auto wiring type. The meter test equipment is controlled via PC-based software. Choices of meter position are 6, 12, 24, 30, 48 and 60.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Tinned Ends
A078HF4-T-0A050
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
779517-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
DIP-ER™ Logic Jumper
Series 115, 116, & 117
-
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
Product
Cable Assy 9-Pin D-Type, M/M, 2m
40-970-009-2m-MM
Cable Assembly
A 9 Pin Cable Assembly suitable for general use and constructed from PFA insulated wire. The connector assembly can be sured to the product by screwlocks.
-
Product
10A DIGITAL MICRO-OHMMETER
MPK-2000e
-
The MPK-2000e digital very low resistance ohmmeter is a portable, microprocessor controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10A. It uses the Kelvin-type, four-terminals measurement principle, thus eliminating errors caused by lead and contact resistances.
-
Product
Wire Gauge Calculator
-
Calculate The Optimal Wire Gauge for Your DC Microgrid or Distributed Switch
-
Product
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth
410112712
Enclosure
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth Includes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With the cable clamps open- stiffener bar can be removed allowing installation or removal of cables without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Tinned Ends, Spring Latches, 2m
A096SFR-T-5B200
-
The 96-Pin 1.27mm pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
I/O Wiring Terminal Boards
ADAM-3900 & PCLD Series
Terminal Board
ADAM-3000 series consists of cost-effective, configurable, isolated signal conditioning modules. They are able to operate in harsh environments.
-
Product
Terminal Block For The 34939A 64-Channel Form A Switch
34939T
Terminal Block
This terminal block is used for discrete wiring. A fully loaded terminal blocks supports up to 20 AWG wire size typical and 18 AWG max. This terminal block has screw terminal connections.
-
Product
9VT Neon Tube Tester
-
West Coast Custom Designs, LLC
When the antenna and/or the Disc are touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate.
-
Product
Terminal Block For 34951A And L4451A D / A Converter
34951T
Terminal Block
Provides a flexible method for connecting discrete external wiring; detachable with screw-type connections.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
Programmable Resistor Modules
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Stress Relaxation Testing Machine
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Model SXW Series Computer Control Electronic Relaxation Testing Machine is designed for the relaxation tests of steel wires, indented wire, and galvanized steel wire etc. This machine adopts vertical load frame with great rigidity, AC servomotor with zero clearance & great torque precise reducer to drive the screw to carry out the adjustment of the test space. the tension of specimen and keeping of the load force. to complete the relaxation test. the machine is equipped with especially designed industry PC. The control and data processing system of IPC has very high reliability, which can meet the requirements of data processing, displaying, storage and data analyzing demanded by the relaxation test that over 1000 hours.
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
Serial Interface
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Strain Relief Plate, Receiver, I2 Micro ICon
310113559
Strain Relief
The i2 Micro iCon strain relief plate attaches to the wiring side of the receiver and can be secured before receiver installation. The strain relief plate is made of aluminum and is black powder coated. It includes 4 wire ties.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 2m, 90º
A1604FT-1604FT-0A200
Cable Assembly
For applications where a 90 degree down cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Ferrules, 0.5m
A003PM5-F-5A050
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Complete Field Meter Site Testing Solution
7 Series
-
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
Product
Micro Vickers Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ MicVision main use in testing materials allows for the measurement of the hardness of small or thin specimens and small areas of larger specimens, MicVision testing is commonly used to determine characteristics of thin sheets, foils, fine wire, epoxies, paints, etc. and is often employed in R&D applications .◆ MicrVision hardness is especially useful in determining hardness variations, caused by hardening, quenching, plating, fabrication, welding or annealing, bonding, etc. Micro hardness testing can be accurately employed using loads as slight as 10 gram, somewhat less and considerably more in certain situation.
-
Product
Cable, 96-Pin Female, Screwlocks To 100-Pin Male, Screwlocks, 1.27mm Pitch, 2m
A096SFR-100SMR-5A200
Cable Assembly
The 96-Pin to 100-Pin 1.27mm pitch Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. M2.5 screwlocks are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
Chassis - up to 8 8x1 Modules, 16 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration for up to 64 Relay Drives
CXM/64-MF
Chassis
These Chassis controls up to 8 8x1 modules, 16 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 64 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
MS-M 26-Pin RF Cable Assembly 0.5m
40-979-526-0.5m-FU
Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
