Additive White Gaussian Noise
-
Product
Dual Output AWGN Generator Line Module
458-AWGN2
-
The Model 458-AWGN2 is the ideal solution for injecting Additive White Gaussian Noise (AWGN) for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing applications.
-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
-
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
-
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
-
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
Product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
-
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
-
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Noise Source, 1 GHz up to 50 GHz
346CK01
-
The Keysight 346CK01 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 50 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 20 dB at 1 GHz, decreasing to typically 7 dB at 50 GHz.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
-
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 3.6 GHz
N8973B
-
The N8973B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8973B.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 26.5 GHz
N8975B
-
The N8975B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8975B.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 7 GHz
N8974B
-
The N8974B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8974B.
-
Product
Phase Noise Test System
N5511A
-
The Keysight N5511A phase noise test system (PNTS) lets you measure at the limits of physics with readings down to kT (-177 dBm/Hz). The N5511A PNTS is a replacement for the gold-standard Keysight E5500 phase noise measurement system and is designed to meet the needs of phase noise power users.
-
Product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 15 dB)
N4001A
-
The SNS series N4001A noise source is ideal for general purpose use with a low reflection coefficent and a nominal ENR of 15 dB from 10 MHz to 18 GHz.
-
Product
Noise Source Test Set, 10 MHz to 26.5 GHz
N2002A
-
The N2002A noise source test set is a low cost, stand-alone instrument that, as part of a calibration system, enables fast, repeatable calibrations with minimal levels of uncertainty.
-
Product
Low-Noise Filter, 210 V / 3 A
N1298C
-
The N1298 Series power source accessories are a collection of low noise filters for the Keysight B2960 Series precision source / measure units (SMUs).
-
Product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
-
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
-
Product
Noise Source, 1 GHz up to 40 GHz
346CK40
-
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
Product
Whiteness Meter
-
Guangzhou Amittari Instruments Co.Ltd
AMITTARI l Whiteness Meter is mainly used to directly measure the whiteness value of object or powder with flat surface. It can be widely used in whiteness measurement of textile printing and dyeing, paint, chemical building materials, paper board, plastic products, white cement, ceramics, enamel, talc powder, starch, flour, salt, detergent, cosmetics and other substances. The instrument pass strict inspection and testing, conforms to the JJG 512-2002 Whiteness Meter Verification Regulation. Also conforms to GB3978、GB3979、GB7973、GB7974、ISO2470、GB8904.2、QB1840、GB2913、GB13025.2、GB1543、ISO2471、GB10339、GB5950、GB12911、GB2409 and other standards.
-
Product
Noise Dosemeters
-
Noise Dosemeters are a type of sound meter designed to measure the levels of noise exposure to an individual over a period of time. All of our dosemeters are compliant to IEC 61252: 1993 / BS EN 61262:1997 and offer high quality and reliable personal noise monitoring solutions.
-
Product
Noise Generator
UFX7000
-
The UFX7000A Series instruments provide Broadband Gaussian noise with superior flatness. The output power can be attenuated up to 127 dB in 1 dB steps, and several connector types are available.
-
Product
Noise Sources
-
This power amplifier ensures that you get the maximum sound pressure level out of the Norsonic range of speakers.
-
Product
Noise Dosimeters
Spark Family
-
Spark® series dosimeters are compact, affordable and tamper-proof personal Noise Dosimeter that measures the following to applicable IEC and ANSI standards:*Noise Exposure: Multiple Dose; Projected Dose; Time Weighted Average; (all with 4 user selectable combinations of Exchange Rate, Threshold, Criterion Level and Criterion Time); Sound Exposure Level*Sound Levels:; Leq; Lmax; Lmin; Lpeak/Luwpk, SEL and more*Time and number of events above Ceiling Level (115 dB) and Peak Level (140dB)
-
Product
Noise Dosimeter
doseBadge5
-
The doseBadge5 is the next generation doseBadge noise dosimeter from Cirrus. It provides all of the unique features of the original doseBadge such as no controls, cables or displays with a range of new functions and features allowing it to be used for compliance with any occupational noise standard. Wireless communication to the dBLink App (for Android and iOS) or the doseBadge5 Wand allows the instrument to be configured and controlled without user intervention. Measurements can be scheduled to start, pause and stop automatically with the timer functions allowing the doseBadge5 to be deployed quickly and easily.
-
Product
Noise Location Package
Type HFDF
-
National RF’s Type HFDF high frequency location system is a proven noise hunting and location directional antenna system that allows you, in many cases, to walk right up to the source of High Frequency (HF) noise! Used by several power companies around the United States, professional noise hunters, and other communications specialists, the HFDF has located noise sources that emanated from pole power transformers, arcing electric fences, CATV in-line amplifiers, plasma TV screens, and even Marijuana grower’s heating lamps! The system incorporates several plug-in, tunable magnetic loop sensors of a proprietary National RF design, that cover the frequency range between 1.8 MHz and 55 MHz. The unit is packaged in a hand-held, lightweight metallic enclosure, with a pistol grip and a magnetic compass mounted on top. The compass is used to get magnetic bearings to the noise source, which may be plotted on a map to triangulate, and ultimately pin-point, the location of the noise source. In certain cases, our customers tell us that they have been able to walk right up to the interfering noise source and correct the situation on the spot!
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
Product
Noise Monitoring Kit
LxT NMS SoundExpert
-
In addition to the SoundExpert LxT meter, this kit includes the EPS042 protection case and D-cell battery pack, the EPS2116 microphone protection shroud, and EXC010 10 ft. cable. Using D-cell alkaline batteries, allows the noise monitor to be smaller and lighter; avoid the expense of shipping heavy lead acid batteries and the hassle of recharging. You can transport it easily to your site, deploy it, measure data, retrieve your system, download the data, and issue your report.
-
Product
Noise and Vibration Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's unique Noise & Vibration Test Systems come fully equipped with the latest industry features. The on-screen operator display in our testers make it easy to set-up, read, track and record your noise or vibration information. We work directly with you to determine the best solution that will work for your application. Our data logging make sure that important data is stored and available for download for future reference. ESW's design engineers work to make sure the testing interface is easy for your operators to use. We work closely with our customers to make sure that your unique testing needs are met. Please see the slideshow below to see some of our Noise & Vibration Testers.
-
Product
Noise Source Generators
-
Noise Sources supply white gaussian electronic noise. The output is a flat instantaneous broadband electronic random noise. The noise source converts a DC input to noise. Units are available in bands between 10MHz thru 26.5 Ghz.
-
Product
Noise Test
-
Noise testing is conducted to determine if materials can withstand external noises generated by various sources. It also includes air-borne and structure-borne noise measurements.
