Strain Gage Amplifiers
See Also: Strain Gages, Strain Gauges, Strain Gage Signal Conditioners
-
Product
Saluki SE2031 DSP Lock-In Amplifier
-
SE2031 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 10 MHz. With the advantage of the latest digital signal processing technology and high-speed 16-bit ADC, SE2031 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noise. The performance of SE2031 is as good as other lock-in amplifier brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE2031 integrates some special functions like multiple harmonic measurement, which meets the needs of scientific research and industrial application well.
-
Product
Suitable For Strain Gauge / Load Cell Sensors
SEM1600B -
-
Suitable For Strain Gauge / Load Cell Sensors
-
Product
Low-noise High-voltage Amplifier For Tube-scanners -
HV200/5
-
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
Product
Bench-Top Type Amplifiers
-
– A variety of wavelength bands– Most models have the RS232C / IEEE488.2(GP-IB) interface as default– customization is available– Development of next-generation optical communication systems– Amplification for evaluation of transmitted signals– Detection of faint signals in optical measurements & sensors
-
Product
PXI Amplifier And Attenuator Modules
-
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
Product
Solid State Power Amplifiers
-
Skylink SSPAs incorporate state-of-art DPD and well-done Heat Dissipation technologies with available LDMOS, GaN & GaAs Chips. Solutions of SSPA frequency range from 9kHz to 50GHz and output power up to kilowatts and includes basic PA modules to integrated chassis with embedded software for local and remote control and monitoring.
-
Product
Broadband Power Amplifier
PAS-00210-60
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 51.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
Product
Strain Sensors
-
Columbia Research Laboratories
Columbia's foil strain sensors monitor the fatigue loading experienced by tactical aircraft under various conditions of speed, weight and missions configuration. Critical undercarriage structures and control surfaces may be monitored for fatigue damage induced by high-G maneuvers and high stress landings. These sensors are self-temperatures compensating, environmental resistant, have a high output, two active arms and are easily installed. Developed for the demanding requirements associated with tactical military aircraft, they are equally useful performing many of the more common strain measurements encountered in the material testing laboratory. Columbia's foil strain sensors are considered the standard for the industry.
-
Product
Low Power Op Amplifiers (< 1mA/amp)
-
Analog Devices low power op amps offer a variety of benefits in many applications such as prolonging battery life, easing waste heat management in end equipment, reducing self heating to minimize thermally induced offset shift, and reducing total system power consumption and cost. Offering power efficient devices without compromising speed, noise, and precision has been a key focus on developing products at ADI.
-
Product
Strain Measurements and Experimental Stress Analysis
-
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
Amplifiers
-
CAES manufactures custom amplifiers in a wide variety of configurations from LNA (Low Noise Amplifiers), Medium and High Power, and wideband solutions.
-
Product
Broadband Power Amplifier
PAS-00260-10
-
* Solid State Power Amplifier* Gain : 49 dB typ.* High IP3, 50.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Type N Connectors
-
Product
RF Amplifiers up to 2500 MHz
-
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
Product
Solid-State RF amplifier module for High Power Testing
-
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 844
-
- Auto Switch over from Fiber to RF & Vice versa- Works as Transmitter & Fiber Amplifier- AGC / MGC - Automatic & Manual Gain Control- Very High MER / BER- High Quality DFB Lasers with Isolators- RF Input : 78dB ~ 90dB- Optical Input : -8dBm ~ +2dBm- Optical Wavelength : 1310nm- Power : 110VAC ~ 240VAC, 50HzSpecifications:- Bandwidth: 47 ~ 860 MHz- Input RF Level: 75 ~ 85dBuV- Input Optical Level:- -8dBm ~ +3dBm- SMPS Power Supply:- 110V AC ~ 265V AC- Power Consumption: 50Watt- AGC Range: 0 ~ -8dBm
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
Product
RF Power Amplifiers
-
Specially selected products to complement our ultrasound measurement equipment.
-
Product
Erbium Doped Fiber Amplifier
S-102
-
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
Height Gages - Electronic
-
A measuring device used for determining the height of objects, and for marking of items to be worked on with an electronic display.
-
Product
The SoundCheck Amplifier
SCAmp Audio Test Amplifier
-
SC Amp is the world’s only dedicated audio test amplifier. Specifically designed for the audio test market, it incorporates several features unique to the needs of audio test and measurement, and unnecessary features found in regular audio amplifiers have been eliminated to keep production line operation simple and error-proof.
-
Product
Solid Plastic Portable Gage
100
-
Dwyer solid plastic portable manometers are precision instruments in inclined and vertical (well-type) styles for the measurement of static pressure, vacuum or differential pressure. To assure the accuracy required in instruments of this type, all machining of bores and wells is to the highest standards of precision backed by Dwyer's years of experience in the fabrication of acrylic instruments.
-
Product
Broadband Amplifiers
-
R&S broadband amplifiers are innovative solid-state solutions with exceptional RF performance for generating RF power up to 13 kW in the frequency range of 4 kHz to 6 GHz. Designed as very compact amplifiers, at highest power density, they are robust against severest output mismatch while featuring high availability. Applications range from amplitude, frequency, phase, pulse to OFDM modulation.
-
Product
Composite 1×6 Video Distribution Amplifier
VDA106
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
High Speed Amplifier
-
TI offers the industry's most comprehensive high speed amplifier portfolio with the widest bandwidth and best in class distortion, precision and power consumption across a broad range of supply voltages. Our industry leading FDA's, DVGA's, TIA's and General purpose amplifiers coupled with the reliability and longevity of our parts makes TI the ideal supplier of high speed amplifiers.
-
Product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
