Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
product
HUM DETECTOR (DEMODULATOR)
HD-500
Matrix Test Equipment Incorporated
The MATRIX Model HD-500 is a detector-amplifier designed to demodulate the low frequency amplitude modulations on any RF carrier over the range of 5 to 1500 MHz. These modulations are usually the undesirable result of the 50 or 60 Hz power source and are not necessarily sinusoidal. The unit is calibrated to the SCTE definition of hum modulation, which is the ratio of the peak-to-peak hum modulation to the peak of the carrier.
-
product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
product
Satellite Interception system
Shoghi has designed and developed various solutions to passively intercept traffic (Voice, Fax and Data) from Global Mobile Personal Communications by Satellite (GMPCS) and point to point satellite communication networks.All solutions are fully integrated monitoring and analysis platform which enables acquisition, processing, storing and analysis of Voice, Fax, Data and High speed IP traffic.To challenge the various monitoring scenarios Shoghi has designed both tactical and strategic solutions equipped with automatic post processing, decoding demodulation and decryption of intercepted Voice, Fax, Data and High speed IP traffic.Our GMPCS Satellite monitoring solutions are capable of intercepting Voice, SMS, Fax and Data traffic along with Call Related Information and Geo-location from Thuraya-2, Thuraya-3, ISAT Phone Pro, Iridium satellite networks.The point to point satellite communication monitoring systems are capable of intercepting traffic including Voice, Fax and Data from C and Ku-band satellite carriers from Intelsat, Eutelsat, Arabsat, Turksat etc. The Satellite Monitoring system can also process and decode GSM traffic on satellite and decode high speed IP traffic online.1.Satellite Monitoring Solutions:2.Satellite Carrier Analysis System3.C/Ku Band Satellite Monitoring4.DCME Analysis System5.GSM Abis Link Monitoring Module6.IP Link over Satellite Monitoring7.Satellite Carrier Reconnaissance and Analysis System8.VSAT Monitoring System9.Satellite Terminal Geolocation System
-
product
Pack (IP) Modules
IP & MM
Industry Pack (IP) modules are international standards as per ANSI-VITA 4.These are mezzanine modules of approximately the size of a business card (99mm x 45mm). Featuring a 16 or 32 bit wide I/O interface and 50 user defined I/O pins, these modules are ideal for providing the capability for high density I/O.IP carriers provide multiple slots on a single carrier. This allows multiple IP modules to be provided on a single slot in a Compact PCI / VME / VXI / PCI card cage.Industry Pack modules provide some unique advantages in system integration. These include:
-
product
OTN: Framer/Mapper/FEC
Macom Technology Solutions Holdings Inc.
MACOM’s OTN Framer/Mapper/FEC family products offer complete portfolio of solutions for 10G, 40G and 100G optical transport networks. They are ideal for high-capacity Carrier Ethernet router/switches, Packet Optical Transport systems and DWDM Transport systems. The OTN framer devices integrate high performance Serdes I/O to allow seamless connection to optical and copper modules. The provisional Tri-FEC integration supports G.709 standard RS-FEC as well as high coding gain G.975.1 I.4 EFEC and I.7 UFEC to improve optical link performance, achieve longer reach and offer interoperability flexibility.
-
product
Dual M.2 Card SSD Mezzanine Module
C48-1-M2
C48-M2 connects to the mezzanine expansion connector HSE of the CompactPCI® CPU carrier. 4HP envelope of the CPU carrier board, but can also be used on some mezzanine side cards, for an 8HP or 12HP total front panel width assembly.
-
product
PCIe Adapter for PMC
PCIe4LBPCI
Now you can use your PCI with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. PCIe4LBPCI ( PCIe Bridge PCI 1 position) adapter / carrier converter card provides the ability to install one PCI card into a standard PCIe (Express) 4 lane slot. Suitable for PCI or PCI-X operation with the PCI; 32 bit or 64 bit data and PCI (25, 33, 50, 66) or PCI-X (50,66,100,133) MHz. clock. Auto selected or switch programmable speeds. The bridge can operate with 1, 2, 3 or 4 lanes active, and can be installed into slots with more than 4 lanes if desired.
-
product
4 Channel ADC FMC Module
ADCFN04 – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
product
96-Pin Micro-D Connector Block, Male With Screwlocks
44-965-096-M
This connector block provides a simple method of connecting to high density 96-Pin SCSI Style Micro-D connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
6U VME Carrier for PMCs and PrPMCs
Ti4400
The Ti4400 is a 6U PMC/PrPMC carrier for VME systems and forms the basis of a flexible I/O system. The user can integrate two single PMC modules or one double-wide PMC.
-
product
Compact PCI Express (3U) Generic Carrier Card
ACCx-1
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
Ethernet Module
M4K-ETH
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
product
PCI to PMC Adapter/Carrier
PCIBPMC
1/2 Length Bridge Based PCI Adapter Carrier Card with PMC Mounting Slot. The PCIBPMC ( PCI Bridge PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCIBPMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit bus operation. The PMC user IO connector Pn4 is brought out to one of two connectors for access (DIN IDC or SCSI II). The signals corresponding to the PrPMC standard Ethernet and Serial lines can optionally be connected to the Ehternet and Serial port connectors at the top edge of the board.
-
product
IDE Controller PMC with 40-pin Interface Connector
5251
The IDE Controller PMC, when mated to a host or carrier card, provides an interface between the PCI bus and as many as four IDE/ ATA devices, via two independent channels.
-
product
Bi-Phase Modulators
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
product
Microwave Transfer Switch Plug-In
1260-162AH/BH
The Astronics 1260-162AH/BH is a 2-slot microwave switch plug-in. It can be used in either the Astronics 1256 switching mainframe or the Astronics 1260-100 Adapt-a-Switch™ VXI carrier.
-
product
Transition Module for 3U cPCI IP Carrier
TCP010-TM
The TCP010-TM is a Transition Module to be used with 3U cPCI IP carrier, providing easy access to the IP I/O lines of cPCI IP carrier with back I/O.
-
product
Interface
RCNIC-A2PA3
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
product
Automated Distortion Characterization and Information System
ADCS
Matrix Test Equipment Incorporated
The Automated Distortion Characterization and Information System (ADCS) is an extension of the Matrix equipment control software that automatically makes RF measurements selected from the following: Cross Modulation (XMOD), Composite Triple Beat (CTB), Composite Second Order (CSO), Carrier to Noise (C/N), Discrete Second Order, Discrete Third Order Distortion. Measurements are made, and the test results and a profile describing the test conditions are saved in a database for later retrieval or reporting.
-
product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
product
Modulator
SFT9264
Hangzhou Softel Optic Co., Ltd.
- 2U chassis, high density to save shipping cost- Support OSD (Logo and Caption) insertion for each channel, easy operation- Suport CC/Subtitle/Teletext- Support BISS De-scrambling (Under developing)- Support program info modify, multiple audio select l - 4 GE ports (max 64 IP input over MPTS/SPTS), Max 840Mbps for each GE input- Support HEVC/H.265, H.264/AVC, MPEG-2 TS Decoding- Processing of up to 64 IP multicast groups of a Gigabit Ethernet MPEG TS into up to 64 standard PAL or NTSC or SECAM TV programs- 64 non-adjacent or adjacent carriers output, each 32 carriers within 400MHz - Support Web-based Network management
-
product
Ethernet
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards (only 64 bit versions). The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.The receive channels allow for the storage of all packets to all MAC and IP addresses with status and Time Tag information appended to each packet. The receivers allow for filtering based on MAC address, IP address and UDP port. The transmit channels enable the user to define a Bus list which controls timing and order of packets without host intervention or immediate mode which enables the host to transmit packets at will.
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
product
CPCI-S.0 Standard Compliant Peripheral Carrier Board
MIC-3810
The carrier board provides a PCIe x16 connector for standard PCIe x8, PCIe x4, PCIe x1 PCIExpress® cards supporting PCIe Gen3 speeds. The carrier board can accommodate cards with maximum dimensions of 176 x 68.9 mm (6.9" x 2.7" inches).
-
product
Vapor Source Mass Flow Controller With Viscous Choked Flow
The 1150C Vapor Source Mass Flow Controllers are pressure based measurement and control systems designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas using viscous flow through a choked orifice.
-
product
Hall Effect Measurement system
HMS-3000
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
product
MPLS-TP networks and TDM / SDH / PDH
CXR offers a full range of multi-service equipment for TDM / SDH / PDH and their evolution over Ethernet and IP networks via gateways TDM over IP.MPLS-TP Carrier Ethernet solutions and provide CE2.0 modes connected on packet transport rsaux guaranteeing quality of service similar to TDM technologies.
-
product
RF Wideband Downconverter Solution From 100 KHz To 27 GHz
DC27G100
GaGe wideband downconverters are wide frequency coverage receivers that feature a single RF input and 3 standard software selectable IF bandwidths, from 10 MHz to 100 MHz, or 3 optional software selectable IF bandwidths, from10 MHz to 160 MHz. The carrier center frequencies can be tuned from 50 MHz to 27 GHz, using direct digitization below 50 MHz.
