Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
Product
PCIe Carrier Boards
-
These non-intelligent carrier cards interface XMC and PMC mezzanine modules and Industry Pack Modules to a PCI Express bus in a PC-based embedded computer.
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
I/O Signal Marshalling
-
We offer you a variety of solutions for I/O signal marshalling in process automation:The flexible VIP I/O marshalling signal marshalling system makes I/O signal marshalling for universal I/O consistent, from the field to the controller. Our Termination Carriers provide you with a Plug and Play solution for standard I/O system signal marshalling enabling you to connect classic DIN rail devices to the standard I/O cards of your automation system.
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
-
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
-
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
Dual DSP Module Quad Industry Pack Carrier
CPCI-DUALIPC-6U
-
The CPCI-2IPC-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring high performance, high density I/O or unique combinations, the CPCI-2IPC-6U is theperfect solution.
-
Product
UNO Carrier Stack Supports MXM GPU Module Aims For Image Processing And AI Inference
UNO-MXM-CB01
-
1 x PCIe x4 expansion kit support 35W MXM GPUBundle compact Din-rail embedded PC form factor, UNO-148 series, with Intel® Core™ processors (13th/11th Gen)Expansion modules to accommodate MXM GPU module for powerful computing capabilitiesSupport 4 independent display outputs (3 x DP, 1 x HDMI)Standalone heatsink and fan for GPU stable performanceSupport up to 8GB GDDR6 with ECC (depends on MXM module option)Industrial design with longevity support (5 years life cycle compared to commercial GPU card 1 year)
-
Product
Mezzanine Cards
-
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
Product
Automated Thermal Stress System
ATSS Series
-
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
Product
MTCA.3 Conduction Cooled MicroTCA Carrier Hub (MCH)
UTC041
-
The VadaTech UTC041 is the most feature-rich conduction cooled MicroTCA Carrier Hub (MCH) on the market. Its management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 AMCs within the chassis. It also manages PCIe Gen3 or 10GbE XAUI fabric switch as well as the standard GbE with 10GbE uplink Base Channel switch.
-
Product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
-
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
Product
96-Pin Micro-D Connector Block, Female With Backshell
44-965-096-F
-
This connector block provides a simple method of connecting to high density 96-Pin SCSI Style Micro-D BRIC connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
4G Router
BB-SR30910120-SWH
-
SmartFlex, Korea, 5x Ethernet, Wi-Fi, Metal, Without Accessories. LTE cat.4, 3G/HSPA+, GPRS/EDGE, Korea, 2x SIM - SKT carrier only (KT and LG U+ are not supported). LTE B1, B3, B5, B7, B8, B20, B38, B40, B41. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
USB4-To-MXM GPU Carrier Card
MIOe-UMXM
-
USB4 Type-C interfaced MXM GPU expansion cardMXM 3.1 Type A, B, B+ compatible (PCIE Gen3 x4)Supports NVIDIA® Quadro® & Intel® Arc™ embedded MXM GPUs, up to 115W TGP MXM modulesSupport dual power input: 12~24V or direct 12V DC input4 x DP1.4 support up to 4 display outputsSupport MXM GPU Cooler Smart Fan Control
-
Product
High Density SPDT Plug-In Switch Card
1260-116
-
The Astronics 1260-116 is a 24-channel, Form C, single-pole double-throw (SPDT) switch card for use in either the 1260-100 VXI Carrier or the 1256 GPIB/RS-232 Switching Mainframe.
-
Product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
-
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
Product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
-
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Recorder Carrier Device
RCD
-
The RCD is a carrier signal demodulator for SCADA and Fault Data Recording. the RCD demodulates the carrier to indicate the presence of a relative level of a singal
-
Product
1x4 Multiplexer Plug-In
1260-134
-
The Astronics1260-134 is a sixteen 1x4 multiplexer plug-in card for the Adapt-a-Switch® platform. It installs, easily and directly from the front panel, into the Adapt-a-Switch VXI Carrier, 1260-100.
-
Product
FMC Quad ADC 16-bit @ 1 GSPS and Quad DAC 16-bit @ 2.8 GSPS
FMC231
-
The FMC231 is an FPGA Mezzanine Carrier (FMC) per VITA 57 specification. The board has quad ADC (the ADC chips are dual channels) and quad DAC (the DAC chip is quad channel). The FMC231 utilizes TI ADS54J60 (option for ADS54J69) providing 16-bit conversion rates of up to 1.0 GSPS and a DAC DAC39J84 providing 16-bit conversion rates of up to 2.8 GSPS.
-
Product
Single-Channel DC Powered Carrier Demodulator
CD16
-
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
Product
CATV Multi-Carrier Generator
1685
-
The Model 1685 is a headend / hubsite RF eight carrier generator. Each CW carrier can be activated individually or simultaneously. The RF carriers generated are extremely clean and stable, thus making the 1685 an ideal instrument for testing/aligning the CATV forward band.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for two M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-32e
-
This Squid PCIe Carrier board can support up to two M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2230, 2242, 2260,2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
Squid Carrier Board™ Family PCI Express Gen 2 Carrier Board for 4 PCIe M.2 SSD Modules
SKU-086-01
-
The Squid PCI Express Carrier board for M.2 SSD modules is the second product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 4 M.2 PCI Express SSD modules. This product is recommended for use in Mac Pro Desktop computers.
-
Product
PXIe Module Carrier
HMPXI AXIe-1
-
The PXIe module carrier, HMPXI AXIe-1 Gen3 x4, is specifically designed to support PXIe modules in AXIe systems, allowing you to maximize the best of both standards in a single system. The HMPXI AXIe-1 carrier is designed as a single-slot AXIe-1 module and allows you to simultaneously install two single-slot PXIe modules.
-
Product
Automated Control System
TermoPress
-
Create a system for controlling and regulating the temperature of hydraulic press plates, as well as recording the current temperature and pressure values. Solution The system has the following basic functionality:configuring and setting the working parameters of presses;start and stop the technological process of the individual press;temperature control and pressure control;forming a timetable for the work of presses;registration of process parameters on an electronic carrier;archiving and viewing of archived data;construction of reports on the technological process in text and graphic form;Turn on and off the power of the press groups.
-
Product
VSAT Interception System
VSAT
-
VSAT Monitoring system is a state-of-the-art Automated Passive VSAT Interception capability designed to meet the aspirations of our customers, to enable them to intercept and process various VSAT networks and their terminals in an interactive and automated manner. The system is conceptualized in such a manner that it can be used for both searchings for new VSAT networks as well as monitoring the content of target VSAT networks, with real-time decoding/decryption and reconstruction of Intercepted traffic. The Satellite Carrier Reconnaissance and Analysis System module come pre-integrated with the VSAT Interception system, to provide the capability to search for new VSAT networks on the selected satellite and offers a snapshot of the captured carriers and its payload. The Analysis tool can provide payload information, based on which the selected carrier can be chosen for the interception.
-
Product
FPGA/FMC Carriers
-
Our AMC FPGA modules feature Altera Stratix IV, Altera Stratix V, Xilinx Virtex-5, Xilinx Virtex-6, Xilinx Zynq, Xilinx Artix, Xilinx Virtex-7 and Xilinx Kintex-7 FPGAs. We also offer a range of carriers that can accommodate standard FMCs featuring FPGAs from Altera and Xilinx, including the new Xilinx UltraScale family.
-
Product
60 GHz WR-15 Waveguide Tx Module
PEM010
-
The PEM010 is a highly integrated millimeter wave transmitter that covers the 60 GHz global unlicensed spectrum allocations packaged in a standard waveguide module. Transmitter architecture is a double conversion, sliding IF with wide bandwidth capability through the up-conversion chain from baseband to carrier. The I/Q interface accepts analog baseband signals which provides for flexibility in design and applications. The baseband input optionally supports FSK/MSK modulation for non-coherent applications. The transmitter incorporates a complete waveguide interface with low-loss transition between the chip and the WR15 waveguide port. The integrated package is small and lightweight, with a simple to use multi-pin ST4 connector for power, reference clock, digital control port and baseband signals. Either of two reference clocks can be used for setting 540 MHz or 500 MHz channel spacing.
