Masters
See Also: Slave, Master Jumpers
-
product
Monochromator Gratings - Type IV
HORIBA Scientific produces a wide range of holographic master gratings from which high precision replicas are manufactured.Using Type IV aberration-corrected monochromator gratings, a single concave grating disperses, collimates, and refocuses the light from the entrance slit onto the exit slit. Wavelength scanning is obtained through a simple rotation of the grating.The groove spacing of these gratings is computer-optimized to produce high quality images with a minimum of astigmatism and coma, even at large numerical apertures. Compared with Czerny-Turner monochromators (equipped with one plane grating, one collimating mirror and one focusing mirror), Type IV aberration-corrected monochromator gratings provide much better light collection efficiency and signal-to-noise ratio.
-
product
VXI PCI Express Crate Controller
V124
The V124 is a VXI bus master crate controller, usable as a crate slot 0 arbiter or as a secondary controller. Each PCI Express cable driver board, in a PC backplane, can drive one to four V124s over standard, flexible PCI Express cable assemblies up to 7 meters long.
-
product
Engine Control
StepGenerator4
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
Hydraulic Power Supply
The Hydraulic Power Supply furnishes the Exciter Head with its hydraulic pressure, flow and filtration requirements. Xcite Hydraulic Power Supplies present a unique approach to meeting the fluid power requirements of the exciter heads. Each unit is transportable and self-contained to permit use at virtually any test site, yet its low noise characteristics make it equally suited for laboratory use. Power supply control is located on the Master Controller for ease of use. All Xcite power supplies furnish 3,000 PSI of pressure and are available in models ranging from 1 GPM to 30 GPM.
-
product
Fully Automatic Colorimeter
DRK103C
Shandong Drick Instruments Co., Ltd.
(1)5 inch TFT color LCD touch screen, the operation is more humanized, new users can be mastered in a short period of time using the method.(2)Simulation of D65 lighting lighting, using CIE1964 complementary color system and CIE1976 (L*a*b*) color space color difference formula.(3)The motherboard brand new design, using the latest technology, CPU uses 32 bits ARM processor,improve the processing speed, the calculated data is more accurate and rapid electromechanical integration design, abandon cumbersome testing process of the artificial hand wheel is rotated, the real implementation of the test program, a determination of the accurate and efficient.(4)Using d/o lighting and observation geometry, diffuse ball diameter 150mm, diameter of the testing hole is 25mm.(5) A light absorber, eliminate the effect of specular reflection.(6)Add printer and imported thermal printer, without the use of ink and color, no noise when working, fast printing speed.(7) Reference sample can be physical, but also for data,? Can store up to ten only memory reference information.(8) Has the memory function, even if the long-term shutdown loss of power, memory zeroing, calibration, standard sample and a reference sample values of the useful information is not lost.(9) Equipped with a standard RS232 interface, can communicate with computer software.
-
product
Compare Color Measurement Instrument
DRK8636
Shandong Drick Instruments Co., Ltd.
WSL-2 Comparison of color measurement instrument (tint meter) is a visual color measuring instrument, which uses a special color internationally recognized a Lovibond color scale to measure a variety of liquids, gels, solids, and powder samples of color. The instrument has a simple structure, convenient operation characteristics, commonly used in color measurement grease, paint, plastics, jam, textiles, food, and other different substances. Lovibond color scale is a special color units, it is a very simple and quite perfect digital color language. Therefore, it can be easy and intuitive to measure a variety of colors, easy to master. Lovibond color measurement instrument has been accepted by many countries in the world,the increasingly widespread application.
-
product
Master Oscillator Multiplexer
MOX Series
*Low phase noise OXCO *Interface between VSAT Modems and Frequency Converters *Robust housing is gasket sealed for weather resistance *OCXO iwth low G-sensitivity available *Single or dual multiplexer *Single or dual bias tee *Available in various OCXO frequencies: 10, 50, 100, 120 MHz
-
product
8-Channel VME Delay Generator for Facility Timing Systems
V880
The V880 is a VME-based system timing module, used to distribute picosecond-precision timing pulses across physically distributed facilities. The V880 receives a 155.52 MHz (OC3 rate) fiberoptic master timing signal and outputs eight local triggers.
-
product
Gratings for Scientific Research
HORIBA Scientific’s diffraction gratings are found in cutting-edge scientific applications including ultrafast and highenergy lasers, space flight instruments, astronomy, and synchrotron spectrometers.HORIBA’s scientific gratings are either masters or replicas, depending on the application. HORIBA Scientific also produces custom diffraction gratings, which can be specified according to our customers’ unique technical requirements.
-
product
Diode Pumped Actively Q-switched Lasers
NL120 Series
NL120 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 10 J per pulse with excellent stability. The innovative, diode‑pumped, self‑seeded master oscillator design results in Single Longitudinal Mode (SLM) output without the use of expensive narrow linewidth seed diodes and cavity‑locking electronics.
-
product
Copy Tools
DemiPG520
Main unit weight is approx. 650g, A5 size ultra compact design Results in superior portability, perfect for on-site data deletion, copy and backup.Clip (specified capacity) function installed Capacity of target HDD is identical to master HDD. This function can be disabled.Compatible with SATA II (3Gbps) Realizes high speed data transfer at 8.5GB per minute (*1).(*1 Transfer speed varies according to performance of connected devices.)Used area analysis and copy functions Used area analysis, copy & compare only for used area available.Compatible with MBR and GPT. FAT, FAT32, NTFS, EXT2, EXT3Deletion and quick diagnostic functions installed. Deletion: One-time, NSA, DoD, Quick diagnosis: SMART self diagnostic function
-
product
Motor Drive Control
Four motor speed drive control models ranging from a simple speed dial/display to complex machine/process synchronizers. Capable of many motor/machine control schemes, from open-loop master to closed-loop pulse-locked speed/event synchronized follower. Compatible with all motor speed drives of any size/power rating with an analog input (AC, AC Vector, DC and Servo)
-
product
DC Resistive Load Banks
LB-Series
Eagle Eye offers multiple DC Load Banks ranging from 10 480 VDC at 1 amp or 5 amp Resolution. These load banks offer a simplistic solution to UPS Battery Load Testing. Each load bank is easy-to-use with an LCD display operator control panel and user-friendly fan switches, load step switches, and master load switches. UPS load testing stimulates a real-world performance demand of a critical power
-
product
Multi-Channel Clock Generator
XCLK1
Curtiss-Wright Defense Solutions
High-speed analog IO acquisition systems need a high quality master reference sample clock.Accurate synchronization in the 100MHz and up frequency domains is not easy and it’s a critical performance limiting factor if not done well. The XCLK1 multi-channel clock generator solves these problems.
-
product
Interface Adapter. USB Solution
U2C-11
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
780575-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
product
XCITE 1100 Field Test Series
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
-
product
High Performance High Power DC Electronic Load
IT8900A/E Series
IT8900A/E series high performance high power DC electronic load provides three voltage ranges 150V/600V/1200V, stand-alone power from 2kW to 54kW. IT8900A/E series, with ultra-wide voltage and current range, controlled by an independent master unit.
-
product
GPS- Based Video Sync Generator
A multiple output SD RS-170A analog composite video blackburst and video sync signal generator that is genlocked to the atomic clocks in the Global Positioning System. The GPS-MSG quartz crystal master clock is continuously phase controlled to accurately track the time from the GPS satellites.
-
product
NI-9145, 8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis
784756-01
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
product
Ethernet-based Distributed Systems
DMC-3425
The DMC-3425 is the first product in Galil's new E-Series line designed specifically for Ethernet-based distributed systems. The DMC-3425 provides a highly versatile and powerful form of distributed control where multiple DMC-3425 controllers are linked together. When linked, one DMC-3425 is designated as the master over the other DMC-3425 controllers in the distributed system.
-
product
Fieldbus Components
The range of fieldbus components offered by ifm includes gateways, IO-Link masters, RFID evaluation units and encoders. Gateways establish the connection between AS-i and common fieldbus systems such as EtherNet/IP, Profibus, Profinet or EtherCAT. They control the data exchange to the sensor/actuator level and communicate rapidly with the superior control level. Variants with PLC functionality or fail-safe PLC are available.
-
product
Sand And Dust Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
product
Gauge Blocks
Practical master gage for dimensional measurement Two types of steel and ceramic gauge blocks are available. Four classes of Class K‚ Class 0‚ Class1‚ and Class 2
-
product
Camera Master
CM-1V
The Camera Master is a digital, hand-held, battery operated meter that measures five different characteristics of the video signal from a CCTV camera or other video sources.
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
Wire Harness Tester
Panther4HT Master- Slave DSU
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
product
Analysis Tool
CANalarm
The CANalarm is a low priced analysis tool that can be installed in the bus permanently. It makes it possible to build up a separate and redundant monitor without change of configuration and program of the master controller. It works passive and is therefore non reactive
