Filter / Amplifiers
See Also: Filters, EMI Filters, Low Pass Filters, Programmable Filters
-
product
High-Voltage Amplifiers
Power amplifiers are a must in applications requiring both complex signals as well as high voltage throughput. However, this is uncommon in high performance instrumentation, therefore an external amplification device must be used. In these cases, a high voltage amplifier is used to increase the size of a signal by some factor.
-
product
Isolation Amplifiers
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
product
Components - Power Amplifiers (FPA)
FPA Series
FPA series driver amplifiers and power amplifiers are discrete and/or MMIC pHEMT device-based amplifiers that operate over the frequency range 18 to 110 GHz for high output power applications. The amplifiers are offered in two categories, standard and custom built up to 250 GHz.The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration. The optional input and output integrated isolators are available to further improve the port return loss.
-
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
product
RF Amplifier
SA1012
Hangzhou Softel Optic Co., Ltd.
*Forward path use import low noise push pull amplify module or GaAs push pull module,2 Power-Double module or GaAs amplify module are used as output stage, Output level is stable and nonlinear index is good, import high index amplify module are used on return path, It's distortion is little and SNR is high.*It is more convenient to debug because of plug-in(or adjustable) duplex filters, plug -in fixed(or adjustable)equalizers, plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
product
Low-Noise Filter, 210 V / 3 A
N1298C
The N1298 Series power source accessories are a collection of low noise filters for the Keysight B2960 Series precision source / measure units (SMUs).
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Low Noise Amplifiers
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
product
Amplifier Module
LNAM-FBX
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
Analog Summing Amplifier
SIM980
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
product
Capacitor for DC Filtering
FIL2
Lifasa - International Capacitors, SA
FIL condensers are specially designed for use in direct current sources and their functions are to filter the alternating output ripple as well as protect the line from momentary spikes and sudden power surges.
-
product
RF Amplifiers up to 1000 MHz
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
product
RF Amplifiers
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
product
Low Noise Amplifier
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
product
RF & Microwave Broadband Amplifiers
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
product
RF Filters
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
-
product
Broadband Power Amplifier
PAS-08042-60
* Solid State Power Amplifier* Small Signal Gain: 60 dB typ.* Rack Mount Case* Internal Cooling Fans*Type N Connectors* Over-voltage, over-current protections
-
product
Fully Differential Amplifiers
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
product
Low Noise Amplifier
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
-
product
PXI Bus Signal Amplifier
3222
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
General Purpose Op Amplifiers
When your design requires general purpose op amps, Analog Devices broad portfolio of high speed op amps, precision op amps, and instrumentation amplifiers deliver the unmatched performance and exceptional value that you’re looking for. Explore our selection of op amps by your necessary parameters and find expert, system-level advice to address your design issues by consulting with ADI resources such as EngineerZone.
-
product
Polarization Maintaining Band Pass Filter
Zhongke Rayzer Optical Technology Co.,Ltd
Selects the thin film filter withgood performance to ensure the high quality opticalperformance, stability and reliability. It is uses to shieldnoise signal in EDFA and fiber laser system. It has thecharacteristics of high isolation, low insertion loss, highreturn loss and high power.
-
product
Programmable Oscillator Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
product
Broadband Power Amplifier
PAS-00023-25
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
product
RF Bidirectional Amplifiers
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
product
Wi-Fi Network Equipment Amplifiers
We offer discrete and integrated amplifier solutions for Wi-Fi network equipment. Our integrated Wi-Fi modules can include multiple power amplifiers, low noise amplifiers (LNAs), switch solutions, filters (band-edge, cellular coexistence, harmonic and out-of-band rejection), diplexers, power management and device matching.
