Bus Interfaces
Enable bus interoperability.
See Also: Interfaces, Serial Interfaces, Parallel Interface, UI, MIPI, Interface Adapters, Bus
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Desktop Test Interface Station
2210
-
TESCO’s new Desktop Test Interface Station (Catalog No. 2210) provides metering professionals with exceptional testing flexibility. The Test Interface Station is ergonomically designed for meter technicians working in a lab or a desktop, yet still rugged for field use. The Test Interface Station includes a zero insertion force (ZIF) meter socket, voltage selection, form selection, open/closed-link selection and bi-directional cabling to power a load box/test kit & connect test standard potentials. When combined with a test kit/test standard and powered via 120 VAC, the Test Interface Station creates a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state).
-
Product
cPCI Intelligent Interface Card
IIB-1553-CPC
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
Product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
-
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
Product
DMX to Analog Interfaces
-
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
Product
PXIe-SMN Interface Card
-
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
Product
Audio Analyzer and Digital Audio Bus Module
DP-cPCI-5667
-
DP-cPCI-5667 is a 6U cPCI Audio Analyzer and Digital Audio Bus Module. This card implements low speed digital audio bus, high speed digital audio bus and audio analyzer features. It is used for general purpose analogue audio analysis and supports low speed digital audio bus and high speed digital audio bus protocols.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Au Truck / Bus Fleet Management System (FMS) Simulators
-
The Au Truck / Bus Fleet Management System (FMS) simulator can generate Controller Area Network (CAN) signal per Truck FMS Standard (Vers. 02.00) and Bus FMS Standard (Vers. 00.02). Au FMS simulators are designed very easy to use. All editions can run independently (without personal computer). Au FMS Simulators are widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration, to product development and product validation.
-
Product
Hall Sensor Board with I2C Interface
046-322
-
Version: +5V/15A +12V/5A -5V/15A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Mini Munitions Store Interface
MMSI
-
Mini Munitions Store Interface (MMSI) (EBR 1553) modules support up to 8 MMSI hub ports and composite Bus Monitor output using the M4KMMSI module. Each module can operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor, and Bus Monitor.
-
Product
44U (77") Insulated Bus Bar
BB-77-I
-
44U (77") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
Parallel Interface Voltage Output D/A Converters
-
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
Product
Interface Adapter
U2C-12
-
Dimax U2C-12, all-in-one USB-I2C, USB-SPI and USB-GPIO Bridge device, converts PC USB transactions to the I2C Master, SPI Master transactions and GPIO functions. U2C-12 turns your PC running Windows, Linux or MacOS into comprehensive I2C/SPI Bus master.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
GPP-95-2 Test System Interface Probe
GPP-95-2
-
Overall Length (mil): 375Overall Length (mm): 9.53Rec. Mounting Hole Size (mil): 85Rec. Mounting Hole Size (mm): 2.15Recommended Drill Size: #44 or 2.15 mm
-
Product
Digital/Pattern/PE Card
PEMU32
-
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on the proven architecture of the PE32, the PEMU32 offers high voltage PMU/DPS and pin electronics in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PEMU32 also supports deep pattern memory by offering 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 10 MHz.
-
Product
Interface Measurement
-
Interfaces, that is, boundaries between separation layers, can be found everywhere in the process industry, e.g. in the chemical or oil & gas industry. An interface arises when two media with different densities are filled into a container: for example, water and oil. To separate the two media from one another, it is necessary to determine where the transition from one medium to the other is located. VEGA sensors can be used to measure both the total level and the interface reliably.
-
Product
850 Universal Interface
UI-5000
-
The most powerful educational lab interface in the world features numerous ports, a rapid sampling rate, and unmatched functionality.
-
Product
Single Port Serial Interface
APCI-7300-3
-
*PCI interface to the 32-bit data bus. *Asynchronous communication adapter, 1-port serial interface*1 socket for SI modules*Modular structure through SI modules*Configurable as: RS232, RS422, RS485, with or without isolation, or 20 mA Current Loop (active, passive) with isolation*Addressing through software
-
Product
ARINC PC/104-Plus Interface Card
PC104P-A429
-
Alta Data Technologies’ PC104P-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
I2C High Speed Interface for USB
Tracii XL 2.0
-
telos EDV Systementwicklung GmbH
Tracii XL 2.0 is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 3.33 Mbit/s. Additionally Tracii XL 2.0 can work as an I2C monitor.
-
Product
INTERFACE TEST FIXTURE KITS
GENRAD 2270
-
Test-X GR Series CAM/TRAC® kits offer the same "Z" axis motion as the standard CT Series with the advantage of interface compatibility.Standard features include locking handle assembly, 3/8" FR4 probe plate, and 12 position I/O block interface..
-
Product
PCI Bus Analyzer / Exerciser
PCI650
-
Silicon Control introduces an economical analyzer and exerciser for PCI systems. This 3rd generation PCI analyzer combines high performance hardware with a sophisticated and intuitive software interface. The result is a powerful diagnostic tool for bus analysis all on a single plug-in card.
-
Product
VME Display And Bus Analyzer Module
VM-DBA
-
VM-DBA is a new test and diagnostic module for VME-bus systems which visualizes activities on all VME bus lines on the set of front-panel LEDs, but also allows one to digitize individual waveforms of all these lines into 2kBit -long storage memories, for a subsequent readout via VME or USB interfaces.
-
Product
Professional Technician Interface
d-briDGe Pro
-
The d-briDGe PRO is DG Technologies’ newest product and is used in conjunction with software applications to provide reprogramming and diagnostics to essentially all J2534 compliant domestic, Asian and European vehicles.
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
PMC Basic Protocol Tx and Bus Monitor
Sy629PMC-BPM
-
The Sy629PMC-BPM card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory.
-
Product
Interface conversion adaptor
IA-Series
-
"IA-series" is an adapter BOX for converting LVDS, PANELLINK output from a video generator to either LVDS, PANELLINK or analog signals. There are five types of adapters. Conversion adapter ON/OFF power function allows connecting or disconnecting hot line without turning PC power off when using a type VG PCI board.
-
Product
Network Sensor Interface for USB Pressure Transducers
SI314
-
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
