Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-114-M50
The 40/42-850A-114-M50 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781116-01
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
-
product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-JDP
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
product
PXI Dual 2x2 Insert/Bypass Switch SC
40-860-222-M
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Series Low Frequency Vibration Sensors
AC136
Low Frequency Accelerometer, Side Exit Connector / Cable, 500 mV/g
-
product
Azure Data Factory
A fully managed, serverless data integration solution for ingesting, preparing, and transforming all your data at scale. Integrate all your data with Azure Data Factory—a fully managed, serverless data integration service. Visually integrate data sources with more than 90 built-in, maintenance-free connectors at no added cost. Easily construct ETL and ELT processes code-free in an intuitive environment or write your own code. Then deliver integrated data to Azure Synapse Analytics to unlock business insights.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 2m
A068SFR-F-5A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Standard Voltage 9 Pin D-Type Cables - Connector to Unterminated for Pickering
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 9-pin D-type connector.
-
product
Cable Tester
LW3310
Dongguan Longwei Electronic Technology Co., Ltd.
LW3310 wire tester is designed for all kinds of electronic wire, electric wire and connector design, due to the various types of wire and connectors used in every field, this applies only to the commonly used wire detection instrument. Widely used in computer, communication, medical, electrical appliances, motor, automobile and other wiring test.
-
product
Coaxial Short
85140B
The Keysight 85140B coaxial short is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm female connector.
-
product
Low to Medium Test
KI-TK035
1310/1550 nm & 850/1300 nm source & power meter, inspection microscope, cleaning materials. Interchangeable MPO, MPO/APC, SC, LC connectors (EAR99 Restricted)
-
product
EBIRST 200-pin LFH To 160-pin DIN Adapter
93-002-410
eBIRST adapters allow extension to other switching system connectors, including SMB
-
product
Ultra Compact, Uncooled Thermal Imaging Core
Dione 640 OEM Series
The Dione 640 OEM series is based on an uncooled 12 μm pitch microbolometer detector with a 640 × 480 resolution. The NETD is less than 40 mK (available upon request) or 50 mK. The cores are optimized for low SWaP (Size, Weight and Power). The overall size of the OEM core is 25 x 25 x 10 mm3 and weight is 6 gr. It utilizes Xenics image enhancement for advanced image processing while keeping power consumption low. All Dione 640 versions have the same SAMTEC ST5 connector and are GenICam compliant.The ultra-compact Dione 640 OEM series find application in safety and security systems, as well as in industrial thermal imaging systems.
-
product
Standard RF Fixture
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
product
SIMRC - 16-Channel 2-Pole Multiplexer
1020-R-16-2-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
78-Pin D-Type Block Without Backshell
92-965-078-F
This connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
PXI I/O Adapter For M983xA, M980xA, And P50xxA VNAs
Y1731A
Access control signals of the M983xA and M980xA PXI VNAs or the P50xxA/B and P93xxB Streamline Series VNAs with twelve SMB connectors.
-
product
PXI Single 36 Channel MUX, SMB Connectors
40-735-912-S4
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
Cable Assembly 15-Pin D-Type, Male to Male, 2m
40-970-015-2m-MM
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
22-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 1m
A022KMR-C-HA100
This is a 1m long male to unterminated 22-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
product
Single Port RS232 Serial Communications Compact Flash Card With Ruggedized Connector
CF232-R
The CF232 is a tiny Type I format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters). The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Tinned Ends, 1m
A009DM5-T-0A100
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
product
PXI 20 Banks of 8 Channel 1 Pole MUX
40-615-022-20/8/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 2m, HV
A009DM5-T-HA200
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
15-Pin D-Type Connectors & Cable Accessories
Our 15-Pin D-Type connector is used on PXI switching products to provide a medium density user connector solution.
-
product
3.5" Embedded SBC With Intel® Atom® Processor E3845/E3827, LVDS/VGA/HDMI, Dual LANs, Audio And ZIO
CAPA840
The CAPA840, a fanless 3.5-inch embedded single board computer, is based on the latest generation of Intel® Atom® processor E3845 or E3827 featuring 1.91/1.75GHz clock speed. Two DDR3L SO-DIMM slots support system memory up to 8 GB. Moreover, the fanless embedded board delivers better level of processing and graphics performance than previous generation Intel® Atom™ SBCs, while consuming less power. In addition to rich onboard I/Os, the CAPA840 adopts an ZIO connector on the rear-side that integrates PCIe x1, USB, LPC and SMbus expansion. With excellent thermal design, the 3.5” embedded board is able to run fanless and works smooth between -20°C to 70°C environments.
-
product
Cable Assembly 44-Pin D-Type Female to Unterminated With Tinned Ends, 2m
A044HF4-T-0A200
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
PXI 12xSPST High Voltage Power Relay Module
40-330-003
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
product
Cable Assembly, 200-Pin LFH, Male Bottom Exit (Male Screwlocks) to 4x50-Pin D-type, Female, 2m
A200LMB-04F050D5B200
This 200-pin male to 50-pin female D-type 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by screwlocks. This cable assembly can be used with Pickering 50-Pin D-Type connector blocks (refer to 90-005D).
