Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
PXI 2 Amp MUX, Single 32-Channel 1-Pole
40-635-101
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
LXI Microwave Multiplexer, SP6T, 1-Bank, 67GHz, 50Ω, SMA-1.85
60-800-801
Our 60-800-801 is a 1 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Split type AC Current Sensor
CTF-50A
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
product
PS/PT ADAPTOR KIT
PSAT
PSAT UNIVERSAL Ps is a static adaptor for virtually ANY KIND OF AIRCRAFT.PSATUNIVERSAL Ps is very easy to use on the plane: power ON the Succion Unit place the Universal adapter on the aircraft and adjust the Ps port release the Security Valve (blue): You are ready to test your static port !Pneumatic insulation is made with rubber tube. PSAT UNIVERSAL Ps is fittedwith a quick connector, which allows to use the adaptor as a cap for special tests.
-
product
8-Channel Relay Output Board With Housing for Mounting on a DIN Rail
PX8500-G
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
product
8 Connector-Hole Back Extension
9401-BE
Semi-enclosed version of the cabling "doghouse" for the Hawk/PC chassis with rear panel punched to accommodate 8 50/37 pin d-sub connectors. Space is provided to mount the standard DG-style 100 pin edge connector paddles.
-
product
Couplers & Power Dividers
*High power handling 750W Ultra-broadband devices support from 555 to 3800 MHz*Very low PIM <-160 dBc with low insertion loss*Outdoor rated unit with support for 7-16 and 4.3-10 connectors*Designed and produced to ISO 9001:2008 centrfication standards for reliability and quality
-
product
Dual 2 Channel Fibre Optic Mux FC/APC
40-815-022
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
Power Amplifier
2734
The 2734 is a compact class D power amplifier, intended for acoustical measurements in the field or laboratory. All controls and connectors are placed on the front panel, enabling you to set up the 2734 very quickly, and to operate it in horizontal or vertical position. The 2734 is built into a robust flight case making it safe and easy to carry along.
-
product
QuadPOD Conditioning Interface
JT 2147/VPC
The JT 2147/VPC is a variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within Virginia Panel Corporation’s mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry, two independent, programmable TAP modules (of type JT 2149) and two TAP modules with I/O (of type JT 2149/MPV) on a single board that interfaces via the VPC QuadraPaddle connectors type G20x or G14x.
-
product
68-Pin SCSI Micro-D Connector, Female
40-961-068-F
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
COM-HPC Mini Type Modules
The COM-HPC specification add mini type at dimension of 95mm x 70mm in Rev 1.2. It addresses a need seen for a smaller form factor, lower power envelope and lower cost at single 400-pin connector. A single power rail input with 8 to 20-volt range deliver up to 107 watts of power and there are 16x lanes PCIe Gen5 in total.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 0.5m, 250 Port
A500RMR-T-5C050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Ferrite Devices
Ducommun's products include very broad ferrite device selections to cover 100 MHz to 110 GHz operation frequency range. These devices include narrow band drop-in (FID and FCD), connectorized (FIC and FCC), junction (FIW and FCW) isolators and circulators and iso-adapters (FII and FCI). The broad bandwidth versions are offered as full band junction isolators and circulators (FIF and FCF) and Faraday isolators (FFF). These devices feature low insertion loss, high isolation and wide operating temperature range. Low cost and volume production versions of these ferrite devices are available per customers’ request.
-
product
LXI Microwave Multiplexer, SP6T, 14-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-514
Our 60-800-514 is a 14 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
12" Cable
CONA615-2
A 12" cable transitions from an ARINC 615 Data Loader Cable Connector (JT01RE-18A-53S) to an ARINC 603 Airborne Computer Connector (MS24266R-18B-31P)
-
product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
product
PXI Resistor Module Dual 16 Bit With 16XSPDT Relays
40-290-121
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 0.5m, 250 Port
A500RMR-F-5C050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB
42-727A-101
The 40-727A-101 (PXI) and 42-727A-101 (PXIe) are 16x4 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 2m, HV
A037DM5-T-HA200
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
product
37-Pin D-Type Male Solder Bucket
92-960-037-M
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Fast Timing Analysis
Zero-Time Box
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Cut Ends, 0.5m, HV
A009DF4-C-HA050
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
3-Pin Power D-Type Connector, 40A, Female Without Backshell
92-960-003-F
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a direct termination with soldered connections.
-
product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 10A, 1m
A020GMR-C-0C100
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
PC/104 OneBank Board
EMC2-SoM3-100
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-SoM3-100 to be added to robust and rugged installations for various commercial, medical, industrial and military uses and to enable more versatility the EMC²-SoM3-100 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
Microohmmeter
AD-7100
4 Connectors measurement method, Max measurement time 10 sec Indicator of right connect test cables, Lock of test current connectors, Graphical backlight LCD display (240 x 128), True test current indicator, Temperature control of test current stability system,
